Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.

Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.

We really should point out a big deal here and that’s the SawStop. It’s hard to put a price on safety and while the SawStop costs more than 3 times what the Hitachi costs it does offer safety that no other saw in test can offer. For those that can afford the additional cost that feature alone may tip the scales for you. Regardless of price SawStop came in 5th place for the categories we evaluated.
I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.

This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.


Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today. 
The blade is a 24 tooth carbide tipped blade that is durable and long lasting. You can even adjust it to a 45 degree angle for those more difficult bevel cuts. If you’re working on uneven ground, you’ll love the rear feet that are fully adjustable so you can level you work space. You’ll get a lot of use out of the onboard storage that will give you easy access to the push stick and guarding components. Weighing only 45 pounds, you can move the table saw from work site to home with ease.
As for extensions, I have added the TS1002 and TS1003 outfeeds (rear and left side respectively) – They do a great job supporting the workpieces without making the saw the least bit tippy. For my use, I don’t get much use from the left side support, but the rear outfeed is great. Much nicer than setting up an outfeed stand and trying to dial it in.
As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.

Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.
A table saw can be classified in many ways, and I’ve come across terms like contractor, folding, featherboard, hobby, induction, sliding and zero clearance. However, I will conform to the most basic and clear classification and range the tables accordingly. That means I’ll order them by benchtop table saws, jobsite table saws, cabinet saws and hybrid table saws.
If you’re looking to use a wheeled base, you’ll want a standard rectangular unit, not a cabinet with multi-directional extension tables. Double check to make sure the model is compatible with wheeled bases, and make sure you buy your base from the same manufacturer, so you have a guarantee that they’ll work together. No matter what, don’t skimp on your base! Remember that the frame and wheels have to hold up a machine that weighs 1/4 ton or more, so it needs to be incredibly sturdy.
From dust collection and onboard storage through to on/off switches and table extensions, most reputable table saws come equipped with everything you’ll need to rip up the wood of your choice. Whether it’s making your life easier with wheels enabling height and tilt adjustment or a safety feature like the magnetic switch, the functionality of table saws is impressive. You can upgrade the blades, get various jigs or dado blades and generally enhance the way your saw performs.
We absolutely love the guard on this model. Like the Grizzly, the Jet is equipped with a riving knife or splitter, a blade guard, and kickback awls. The Jet’s our favorite of the two to use, because the whole system is modular: you can take it apart or put it back together without using any tools! The splitter (or riving knife) attaches to the same arbor component as the blade, so no matter how you bevel, and no matter what size blade you use, the splitter always lines up without needing any adjustments.
Different types of table saw rely on different motors. With the smaller and more portable saws, 120V direct drive motors can deliver up to 2HP. This is more than enough power if you’re working with less substantial sheets of material. The larger saws have belt drive motors running on 240V. These produce 3-5HP. Think carefully about the materials you’ll be working with. Get the right sized motor for your cutting needs.
Jet also gives you different choices when it comes to the extension wings. Some customers prefer the cast iron wings because they add more weight and keep the table from shifting, but others prefer the stainless steel wings that are durable and easier to use. No matter which wings you choose, you’ll find that you can quickly and easily attach them to the table’s surface to extend the total amount of workspace you have.
We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.
The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
But with top quality saws come features that some people may find well worth the extra investment, substantial though it may be, and thus our discussion starts with pricier models. At the top price range for table saws, you can often get a saw with safety technology that will automatically halt its blade the instant it encounters human flesh. (The process literally takes but a few milliseconds.) The knowledge that your fingers and hands are safe from major injury caused by a rapidly rotating, razor sharp blade is more than convincing enough for many people to invest in these technologically marvelous table saws.
Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.

One important aspect to consider when buying a new table saw or looking for a new blade is axis adjustment. Being able to adjust the vertical height of the blade allows you to control the depth of the cut, it’s also useful when you don’t need to cut all the way through the wood, especially useful with thick pieces of wood. To help making bevel cuts and joints you can adjust the blade to certain angles that you require.
The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.
Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.
If you’re a professional looking for a great table saw for the worksite, you’ll love the features and performance of the DEWALT DWE7480. Equipped with the Site-Pro Modular Guarding System has a rack and pinion telescoping fence rail that will allow you to make fast, smooth and accurate adjustments. This is the perfect table saw for cutting larger shelving and trim easily. With a 15 AMP 4800 rpm motor, you will go through all types of wood, even hardwood, with ease.

Stands are one of those features where the ends really do justify the means. Some made us wish the manual writers would take a cue from Lego—just make the *@#$! things easy enough for a 7 year old to understand. That aside, SawStop set itself aside brilliantly, taking just 10 minutes to setup. All we had to do was install the wheels and two handles. Even the packaging is designed to make the process easier and the instructions were super-easy to understand. Makita was nearly as simple only requiring us to install the handle and bolt the saw to the stand.

The price is okay. SawStop is a well-known manufacturer, and they have a pretty good quality control department. In simpler words, it may seem expensive to some, but it’s well-worth the money, especially if you’re a professional. A vast majority of DIY enthusiasts don’t want to make a huge investment in order to tackle a few minor projects; therefore, most of them tend to skip on buying a professional cabinet saw.


Cabinet saws are the prime choice for professional woodworkers. A more powerful induction motor, usually 3 to 5 HP, is enclosed in a cabinet, as part of a super-sturdy overall construction. This type of table saw is ideal for making smooth, straight cuts through hardwoods without worrying about excessive vibration. All that power and stability comes at a price, though. Low-end cabinet saws start around $2,300 and can go past $5,000 for industrial table saws.
Overall, the Dewalt's combination blade leaves a slightly smoother finish, but both brands' general purpose construction blades are good enough to start off with. Cross and rip-cut edges were fairly smooth, but users who plan to cut down a lot of plywood will definitely want to invest in a more suitable saw blade. Both saws provided ample cutting power without a noticeable difference in cutting speeds, so we're calling this one a tie.
It’s more compact than the Grizzly, and it uses its space efficiently. The Jet only has one extension table, but it makes the most of it. This one gets nearly the same rip capacity as the much larger Grizzly–to within 2 inches! There’s also a closed-off drawer in the bottom of the cabinet, which is ideal for storing all your smaller table saw accessories.
The blades are categorized according to number of teeth, diameter, arbor size, kerf size, application and speed. They can also be divided by material. Regular commercial table saws are 10-inch or 12-inch. Teeth usually number from 24-80. Many blades are tipped with diamond, carbon or carbide. This lets you cut through more than just wood. You will also need to think about the tilt of the blade. They are available in left tilt or right tilt. With a left-tilting hybrid or cabinet saw, the motor cover can get in the way of the sliding table. Router table extensions don’t work well on left-tilting saws. 
Located right next to the hand wheel on the front is a panel that features both a power button and a stop switch. The power button helps the motor come to life quickly without requiring that it heat up first, and you can press down on this button to turn the saw off at the end of the day. The emergency stop switch helps you stop the blade in the middle of a project to prevent accidents caused by clothing or skin coming into contact with the blade.
Bosch 10” table saw has it all in terms of precision and accuracy. It has a riving knife system for high material controls and visibility in cutting. The blade is designed with anti-kickback pawls to ensure once you start cutting, you will get accurate results to the end. The entire unit is designed with heavy-duty material for durability. The square lock rip fence has adjustable style to guarantee continued accuracy and precision in all your work. Additionally, the table saw has an easy to transport design with additional tabletops handles for portability. You can also regulate the cutting speed of the table saw to the place you are comfortable.
×