Table saws can pose a serious risk of injury, since part of the spinning blade comes up above the surface of the table where it can come into contact with the user's hand as it guides the wood. Thanks to voluntary safety standards introduced by Underwriters Laboratories (UL) in 2007, pretty much all table saws now come with blade guards that minimize the risk. Modern guard systems are easier to remove and replace as needed – an important feature because inconvenient blade guards are apt to be left off the saw.
Setting up or taking down Craftsman’s spring-assisted stand is a six-step process, involving various release latches. It’s not intuitive like that of Bosch or RIDGID. And, once the stand is folded down, don’t lift the handles up too far when rolling the saw around, or the stand drags against the floor. A shorter woodworker might find this less of a problem than this 6′ 3″ tester did. I also found that the stand’s narrow stance and light weight couldn’t prevent it from skittering on the floor as I pushed heavy lumber across the top. A word to the wise: weigh the base down for heavy-duty work or for cutting large sheet goods.
The safety brake feature is a real step forward in engineering, but it does have a few downsides. The aluminum brake works with single-use cartridges, so you’ll have to replace the cartridge if you trip the sensor. Likewise, the impact of the brake, stopping the blade in milliseconds, will destroy your blade, so you’ll have to replace that as well. It’s a small price to pay for keeping your fingers or limbs, but it’s probably a good idea to stock up on cartridges and blades
If you want to increase your safety, get a saw that has a flesh sensor. Doing so though will increase the price quite a bit, so only get it if you can afford it or care very much about your safety. A flesh sensor will stop the saw in as little as 0.01s after it comes in contact with your skin. While the blade will be damaged beyond repair, you’ll be safe.Now that you know a bit more about the factors to consider when getting a cabinet table saw, let’s take a better look below at some of the best models you can currently buy.
The table measures up at 29 inches by 21.5 inches. The 4100-09 is not suitable for dealing with large stock or sheets of wood. Made from aluminum, you’ll meet with no resistance as you slide the timber toward the blade. The only negative with the table is the way it’s finished with an anodized coating. This is fine to start with but tends to wear over time, something that doesn’t just look unsightly but can ultimately affect accuracy. This is a surprising oversight from Bosch and one we hope they rectify in future iterations of this fine table saw.
At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.
Buying a table saw is one of the biggest and most important purchases you will ever make when it comes to power tools. It is an integral part of most job site equipment, as well as an essential item for most do it yourself projects. Choosing a table saw that fits your particular needs and budget can mean the difference in both profitability and frustration level.
The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.

At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.
One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
The Bosch 4100-09 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker.. It includes Constant Response circuitry to help maintain speed under load, and overload protection. The Square Lock rip fence is engineered for maximum trueness and great ease-of-use, with the fence able to easily glide along the rail for one-handed operation. The lighter GTA47W Gravity-Rise Wheeled Stand has 8 In. treaded rubber-composite tires and a single-action design for easy set-up and transport. It is jobsite-ready with heavy-duty construction. The Smart Guard System is the first modular table saw blade guard, featuring a three-position adjustable riving knife, anti-kickback pawls and non-obstructed-view barrier guard assembly. The table saw provides a 29 In. x 21-1/2 In. square tabletop with a 25 In. rip capacity for ripping 4 Ft. wide sheets goods in half.
6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
If you’re a professional looking for a great table saw for the worksite, you’ll love the features and performance of the DEWALT DWE7480. Equipped with the Site-Pro Modular Guarding System has a rack and pinion telescoping fence rail that will allow you to make fast, smooth and accurate adjustments. This is the perfect table saw for cutting larger shelving and trim easily. With a 15 AMP 4800 rpm motor, you will go through all types of wood, even hardwood, with ease.

We’re impressed with how much thought SawStop have put into all the features on this model. It has an extra-large bevel gauge ruler on the side of the cabinet, tool-free, modular guard system, and compatibility with innovative wheelbases which don’t add noticeably to the SawStop’s height or footprint. It also has beveled edges to protect your materials, a very nice touch that our other recommendations don’t have. All in all, it feels like a tool designed by people who use one of these units on a regular basis.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
The Grizzly is our top choice for folks who need lots of room to work, plain and simple. Thanks to its dual extension tables, this one has the widest rip and fence capacity of the three units we’ve reviewed here. We also love that it makes full use of the space under the worktops, so you’ll get plenty of storage room to make up for its larger footprint.
Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.

Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.
Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
This type requires a heavy-duty circuit because it’s driven by a powerful 3 to 5HP motor. The blade is driven by three parallel V-belts which ensure a smooth operation and an efficient transfer of energy. Needless to say, if you have big plans, you might want to consider investing in a high-quality cabinet saw. Prompted, it’s going to cost you a significant amount of money, but it pays out relatively quickly.

TBB used the same iGauging 35-125-4 digital dial indicator to measure the accuracy of the as-delivered factory fence to the table miter slot. We started by placing the fence in a locked position about 1” away from the blade on the opposite side from the miter slot. We adjusted the throw of the dial indicator so that we took the readings on the indicator, as before, in the middle of the indicator’s range of movement.


Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.
The JET ProShop Table Saw offers features you The JET ProShop Table Saw offers features you expect from a high-end cabinet saw in the compact design of a contactor-style machine. The transparent blade guard has independent leaves and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts.  More + Product Details Close

We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.
When using the side extension, a tape moves along so you won’t have to remember what measurement to lock the fence on or read a double marked measurement guide. It’s an innovation we like, but there are questions as to the long term durability of the tape itself. Like Ryobi, Ridgid uses a magnetic throat plate to secure it while leaving access simple.

Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.
The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.

Plus, the machined aluminum table is our favorite on the market right now. It also has a smarter motor system than either of the Dewalt’s, thanks to a soft start and automatic speed control to ensure smooth cuts. However, it’s the slowest of the pack, and it doesn’t have quite as good a fence as the yellow competition. We think it’s a great choice for pros who are concerned about accuracy, but can’t spend lots of money on their unit.
As with anything, it’s easy to get overwhelmed with the variety of types, sizes, features, colors, weights, what, when, why, where, who…(let me catch my breath). For now, let’s focus on what’s right for you with our Best Portable Table Saw Guide. We’ll start by identifying quality brands that align with your needs. Besides, who wants to buy something that won’t work?
Optional portable table saw stands are available for both saws. (Bosch's stand is called the GTA500; DeWalt's is the DW7450.) The Bosch features tool-less connection (after initial assembly), while the DeWalt requires the attachment and tightening of four bolts through the DW745's bottom roll cage— though it's nothing a few after-market knobs couldn't fix.
Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.

In recent years, there has been a cloud of controversy surrounding the inherent safety issues surrounding the table saw. SawStop developed a flesh detection technology that pulls the blade below the table surface 3 milliseconds after coming into contact with skin. It really created a new class of table saw that, as of June 1st, finally has some competition in the form of Bosch’s REAXX.


The most critical safety feature on a table saw is the blade guard. It’s all that separates your fingers from the rapidly rotating blade. You need this to be transparent or it will make measuring awkward. The last thing you want is to be tempted to remove an unfit guard. Check closely for a clear, flexible blade guard. Safety is paramount when operating a table saw.
Cabinet table saws are the best choice for full-time professional woodworkers with a dedicated workshop. If you have a spacious shop, these are some of the most efficient, versatile cutting tools you can buy, especially for larger stock. With 3+ HP motors, they’re by far the most powerful machines you can get your hands on. Plus, their heavy, machined build quality gives you a precision and smoothness in your work that really compliments the professional. They have the most effective dust collection systems of any table saw, and durability that can last more than a lifetime.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
We spent 42 hours on research, videography, and editing, to review the top options for this wiki. Regardless of whether you're a construction professional, a precision woodworker, or a DIY hobbyist tackling your next home-based shelving project, one of these handy table saws will help you get the job done fast. Our selections include models with durable cabinets, powerful motors, integrated fence rails, and even patented safety systems to protect you from on-the-job injuries. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best table saw on Amazon.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
×