In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
To avoid such scenario, you can take a moment and check our full reviews out. We offer more than enough insight into the capabilities of particular models we consider are worth checking out. Therefore, if you’re in a dilemma about which table saw to buy; don’t hesitate to refer to this article. The more you know about a certain unit, the fewer problems you’ll have when the moment of purchase comes.
Compared to some of the other miter saws we’ve used – predating the new riving knife requirement, the Bosch GTS1031 guard system is much easier to install and remove when necessary (and to put the saw back into portable mode). We timed ourselves and assembled and tore down the saw in just over 2 minutes – and we were confident that our time would get better with more practice. The table is made of machined cast aluminum and is texture-coated to make it fairly slick – something that really helped when cutting larger pieces of 3/4″ plywood for a workbench surface. As for extending the table – that was super-easy. You just lift the table extension handle upwards and slide the table to the right. This gives you a full 18″ of rip width to the rip fence with your material to the right of the blade. Collapsed, you get up to 10″. Motion of the rip fence and the table extension were smooth. While the fence had some wobble in it at the far end – this completely disappeared when you locked it down – and the shape of the rear of the fence locked it straight every time. It’s a good system and more than adequate for a low-cost portable saw like this. We’ve seen more robust fence systems. But typically the trade-off has been in weight as well as cost.
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
The price is acceptable. One cannot say it’s a cheap piece of equipment because it’s not. But, the high quality of production and a great deal of precision justify the somewhat premium price. If you’re a devoted professional, the price shouldn’t be much of an issue for you. The only downside many people reported is the quality control within the company. Many models came with broken or missing parts.

Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.


Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
The blades are categorized according to number of teeth, diameter, arbor size, kerf size, application and speed. They can also be divided by material. Regular commercial table saws are 10-inch or 12-inch. Teeth usually number from 24-80. Many blades are tipped with diamond, carbon or carbide. This lets you cut through more than just wood. You will also need to think about the tilt of the blade. They are available in left tilt or right tilt. With a left-tilting hybrid or cabinet saw, the motor cover can get in the way of the sliding table. Router table extensions don’t work well on left-tilting saws. 

We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.


If you’re going to be transporting your unit regularly, you should aim to keep weight to a minimum. Look for something lightweight, with convenient carrying handles, or a stand that can be wheeled around dolly-style at the worksite. Conversely, if you’re only going to be using your portable saw occasionally, you can probably stand a bit more weight.
Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.
The Craftsman table saw is one of the most compact of the bunch when it’s folded up. And if you can get it for the sale price of $260, it’s also the cheapest of the best table saw options. The blade guard and anti-kickback pawls are identical to the Porter-Cable and are the hardest of any of the saws to install. And they are the only two blade guards that don’t have a feature to hold them out of the way when you’re adjusting the blade or setting up the cut.
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
×