This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
It is not a cabinet saw, so judging it by those standards would be unfair. As a portable job site saw this is amazing. Loud and dusty, sure, but that is expected. Easy to use and store, yes. The fence is square to the blade, and is rock solid, as long as you make sure the nut at the back of the fence is set right. The fence is not quite square to the table top, and I can't tweak it, but for construction I wouldn't care. I do other fussier things on the saw, so I will shim out an auxiliary fence. I made a cross-cut sled, which I recommend, and get thin kerf blades. I got a rip, general, and fine finish blades, and I get great results.

That’s why we’ve created this handy guide! As usual, our trusty team have taken a comprehensive look at all the options out there. We’ve looked for portable units that don’t sacrifice power or accuracy for their small size. You’ll find our Top Three recommendations below, along with a few additional choices for new woodworkers and demanding professionals.


The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. There is tool-less assembly of the riving knife and anti-kickback pawls. It has a large easy to access ...  More + Product Details Close

Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
Plus, the machined aluminum table is our favorite on the market right now. It also has a smarter motor system than either of the Dewalt’s, thanks to a soft start and automatic speed control to ensure smooth cuts. However, it’s the slowest of the pack, and it doesn’t have quite as good a fence as the yellow competition. We think it’s a great choice for pros who are concerned about accuracy, but can’t spend lots of money on their unit.
Measuring in at 19.9" x 23.4" x 13.4", the SPT70WT-01 is compact enough to fit into any aspiring handyman’s garage, but powerful enough to tackle anything you throw at it on the job site, meaning it’s an ideal entry-level table saw for the amateur hoping to turn his hobby into a career. Sturdiness, durability, and anti-kickback technology make the world’s first worm drive table saw a revolutionary machine. Satisfied buyers can’t get enough of this balanced wood-devouring behemoth.
Being concentrated is extremely important. A big percentage of injuries happen due to the lack of focus at any given moment. Remember, if anything happens, it will happen in under a second. Naturally, you won’t have any time to react properly. Music is something that can be dangerous and relaxing at the same time. Some people love working while listening to their favorite tracks, but it significantly lowers your concentration level. Therefore, you should avoid listening to music while operating a heavy-duty piece of equipment.

After cutting a bunch of wood with this saw, we really liked the balance of power and portability of Bosch GTS1031 – and I think that’s what this saw is all about. For raw Performance, the unflappable motor-blade combo earned a stiff 8/10 in our tests, while its affordable $399 price tag put it at a solid 9/10 in our Value scale. Sure, you can get cheaper portable table saws, but you’ll find it a challenge to track down the combination of power and portability the Bosch GTS1031 offers. Bosch’s gravity rise-equipped 4100-09 remains a compelling alternative or those wanting an integrated stand. It occupies an additional 15″ in width and 8″ in length and is a full 3.5″ taller. But it only tacks on 8 pounds in weight. If you’re cutting larger pieces of wood or need a saw with a stand, the 4100-09 may be your baby, but the new Bosch GTS1031, with its “toss it in the truck” form factor is our new sweetheart tool. While it has an available GTA500 folding table stand accessory, the real advantage of this saw is it’s stand-free portability – so don’t make it into something it’s not. After using this tool, we think you’ll want to take it with you, as-is, just about everywhere!
One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.
That’s why we’ve created this handy guide! As usual, our trusty team have taken a comprehensive look at all the options out there. We’ve looked for portable units that don’t sacrifice power or accuracy for their small size. You’ll find our Top Three recommendations below, along with a few additional choices for new woodworkers and demanding professionals.
The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.
To adjust blade height you simply operate the elevation wheel located on the front of the saw, and the angle of the blade can be set through a switch which is behind the wheel in case you want to make bevel cuts. The angle can be set anywhere between 0 and 45 degrees, and once you’ve adjusted the bevel angle it can be locked into place using the handle.
The safety brake feature is a real step forward in engineering, but it does have a few downsides. The aluminum brake works with single-use cartridges, so you’ll have to replace the cartridge if you trip the sensor. Likewise, the impact of the brake, stopping the blade in milliseconds, will destroy your blade, so you’ll have to replace that as well. It’s a small price to pay for keeping your fingers or limbs, but it’s probably a good idea to stock up on cartridges and blades

For ideal usage, the on/off switch needs to be mounted on the front of the saw and should be easy to turn off with your knee or a swat without having to look at it to locate it. Most table saw models have a safety feature that is a plastic key that has to be inserted before the table saw can be turned on. Some may even have a way to padlock the switch.
Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.
Cabinet saws are the prime choice for professional woodworkers. A more powerful induction motor, usually 3 to 5 HP, is enclosed in a cabinet, as part of a super-sturdy overall construction. This type of table saw is ideal for making smooth, straight cuts through hardwoods without worrying about excessive vibration. All that power and stability comes at a price, though. Low-end cabinet saws start around $2,300 and can go past $5,000 for industrial table saws.

It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.


Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
I’m trying to replace some lost tools for a doctor inflicted, lawyer cowardice sustained injury. I’ve been a woodworker for more years than I might imagine I am comfortable with saying simply for it seems to have been bestowed upon me from birth. The only comment I have is a general comment. As I’ve noticed from about 20 years ago being introduced do officially being educated at a local community college, everyone there had prestige rights attached to it, a couple of cabinet makers I worked for did also that Porter Cable was the Cadilac of woodworking tools. Well, China… Read more »
You can opt to extend the warranty coverage to 3 years, all through an external provider. We actually prefer these third-party warranties for power tools because they allow you to deal with people who are on your side, as opposed to company representatives, who can be frustrating to say the least. We think add-on coverage is a great safeguard for any cabinet table saw, and it’s a very reasonable proposition on this model.
The price is acceptable. One cannot say it’s a cheap piece of equipment because it’s not. But, the high quality of production and a great deal of precision justify the somewhat premium price. If you’re a devoted professional, the price shouldn’t be much of an issue for you. The only downside many people reported is the quality control within the company. Many models came with broken or missing parts.
One important aspect to consider when buying a new table saw or looking for a new blade is axis adjustment. Being able to adjust the vertical height of the blade allows you to control the depth of the cut, it’s also useful when you don’t need to cut all the way through the wood, especially useful with thick pieces of wood. To help making bevel cuts and joints you can adjust the blade to certain angles that you require.
The Bosch 4100-10 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand is a portable table saw with outstanding capacity and capability. The powerful 15-Amp saw delivers 4.0 max HP, with a large machined aluminum tabletop and a wide 25 In. ripping capacity. The Gravity-Rise Stand provides easy setup and take down. The SquareLock rip fence is engineered for trueness. The 4100 table saw also comes equipped with advanced electronics, such as soft start, constant response circuitry and overload protection.
Dust collection can seem like an afterthought for jobsite table saws. The fact that you’re outside, often on an unoccupied site, negates the need to collect your dust. But breathing that stuff doesn’t do your lungs any favors. That’s why dust collection is so important. Of course, if you’re working inside or in an occupied structure, collecting all that dust will make the cleanup part of your day easier to deal with. Since we’re not talking about concrete dust regulations, even a standard shop vac will be a good bet to help contain the mess.

Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
×