Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.

If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.


This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.
The throat plate is the removable piece surrounding the blade that sits flush with the table. Removing it gives you the ability to access the blade for removal or riving knife adjustments. The narrower the blade clearance the better for two reasons. First, it helps keep material from falling into the blade area or lodging between the blade and throat plate. Second, it gives you material support very close to the cut to help reduce tearout as the blade exits the cut.
Contractor saws are a perfect balance between functionality, manoeuvrability and price. These sorts of saws are perfect if you have bigger projects that you’re working on and will stay on site for a few months. This is due to the fact that they are a lot less portable, but that being said they are a great in-between saw as they still have great rip capacity and overall cutting power.

The DEWALT Table Saw is designed with a The DEWALT Table Saw is designed with a 15 Amp 4800 RPM motor that quickly rips through hardwoods with ease. With 24-1/2 in. of rip capacity this saw easily cuts a variety of larger shelving and trim materials. Rack and pinion telescoping fence rails make fence adjustments fast smooth and ...  More + Product Details Close
That’s one major safety hazard which you can completely eliminate with one simple feature. In addition to the magnetic switch, be sure to look for thermal overload protection on the motor. You shouldn’t have any problems with burnout on motors this powerful, but it’s an important safety feature to have just in case, especially for folks who work with thicker hardwood stock. Thermal overload protection shuts the motor off automatically if it’s getting dangerously bogged down.
The blades are the primary factor to consider when shopping for a saw as they hugely determine the performance of your table saw. The blades will only be effective if they are set at a correct depth of cut. The table saw will also perform best if only the correct blade for the cut is fitted, as a proper blade will enable you to achieve a precise and smooth cut. When purchasing a blade, go for the one with a correct setting blade. Consider the cutting depth also as this will determine its suitability for the job. You should also ensure that the table saw is equipped with splinter guard as this will help in minimizing splintering of the board’s top surface. Splinter guard also enhances accuracy because when it is lined up at the start and finish mark the saw will cut with precision. A suitable table saw should also have a 20mm arbor as this guarantees the stability of the blade and hence, safety in the workplace.
In terms of size, the table height from floor measures thirty four inches, with extension it measures twenty seven by forty inches and overall dimensions are 62 by 41 by 40 inches (LWH). This is simply an amazing saw and not only will you use it for many years to come, but it’s going to help you get the professional results you’re looking for in any project.
The 708494K JPS-10TS from Jet Proshop is a high end cabinet table saw which delivers on all your expectations. Available in either a thirty inch or a fifty two inch rip capacity, this model is built from cast iron and is extremely rugged in order to withstand a lot of abuse and still deliver the excellent results you’re expecting from it. Regardless if you’re a professional or if this is the first cabinet table saw you’re planning to get, the 708494K JPS-10TS won’t disappoint. Its rugged build quality and ease of use are going to make it one of the best table saws currently available.
The frame is also improved. Instead of the basic roll-cage on the Dewalt, this one neatens things up with an integrated sub-base. It’s a rugged rubber-like pad which serves as a bumper between the main frame and your truck bed or worksite table. Both the table and the sub base are joined to the main frame, and they provide strength at both ends of the design. As with the Dewalt, you can store your tools and accessories inside, an on hooks outside the Bosch.
The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
Setting up or taking down Craftsman’s spring-assisted stand is a six-step process, involving various release latches. It’s not intuitive like that of Bosch or RIDGID. And, once the stand is folded down, don’t lift the handles up too far when rolling the saw around, or the stand drags against the floor. A shorter woodworker might find this less of a problem than this 6′ 3″ tester did. I also found that the stand’s narrow stance and light weight couldn’t prevent it from skittering on the floor as I pushed heavy lumber across the top. A word to the wise: weigh the base down for heavy-duty work or for cutting large sheet goods.
The body of the blade is made from hardened steel, helping to extend the lifespan and keep up with the tooth quality. The kerf is a crazy-thin 0.098 inch—narrow to keep the cuts fast by reducing the amount of material that needs to be removed. Like most Diablo blades, you’ll pay a bit of a premium up front, but the blade lasts so much longer than others on the market that the cost per cut is much lower.
Editor and "serious woodworker" Chris Marshall tests five "premium" portable table saws. After equipping each saw with a new Freud thin-kerf blade, he uses them to rip lengths of medium-density fiberboard (MDF) and yellow pine, as well as making long dado cuts in MDF. Marshall considers the saws' stability, cutting accuracy, efficiency, dust collection, and general ease of use to choose his top picks. Unfortunately, two of his three favorites are discontinued.
We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.
Just used this saw for the first time today and I love it. Instructions for putting the stand together were not very clear. There's a lot of very detailed reviews here, so there isn't much I can add that hasn't already been said; but one thing I didn't know until using it is that the rear legs are angled further back than the front ones to provide more stability when pushing stock through the saw. Only used it a few times today, but it was a pleasure to use.
Besides that, materials are expensive, and when you ruin even a couple of pricey work pieces with a saw that doesn’t provide accurate cut you will end up paying far more for that cheap saw than you anticipated. Having a good saw that you can depend on for accuracy and efficiency is a solid business move for any contractor. Both the DW745 and the Bosch 4100 have a true riving knife, anti-kickback pawls, and a blade guard to prevent kickback and possible injury.
Due to the position of the motor, dust collection is often an issue with these units, especially in comparison to the cabinet type. However, an industrial vacuum is usually a small and worthy investment which should solve the issue effectively. The main advantage of this type is the fact that it’s much cheaper than its nearest equivalent – the cabinet type.

These are the best choice for long jobs where you’ll get yourself set up at a job site, and need a saw that enables you to make all your big, long cuts without traveling back and forth between the site and your shop. While you won’t want to move these units around frequently, they’re great for seeing a contract through to the end from the worksite.

From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.

I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?


Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.

Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.
The DEWALT DW745 and the Bosch 4100 are pretty evenly matched in having plenty of power and not-so-hot dust collection. I you’re looking for a light weight saw, the DEWALT comes in ahead since it weighs almost half as much as the Bosch. It is also the less expensive choice by far. The large work table, expanded cutting capability, and its Gravity Rise feature (with solid rubber wheels that make it easy to be rolling across rugged terrain at a jobsite) make the Bosch a Cadillac among Pintos, but, of course, that luxury comes with a price tag.
×