Unlike a lot of competing models, this one is updated regularly. Previous buyers appreciated the thoughtful tweaks, which made it clear that Dewalt listened to feedback from folks who used the first versions. Recent buyers noted the improved rack and pinion teeth, which help the fence lock into position with less play. They also appreciated the reinforced rails, which felt a lot less flimsy than the old version.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.

I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
We absolutely love the guard on this model. Like the Grizzly, the Jet is equipped with a riving knife or splitter, a blade guard, and kickback awls. The Jet’s our favorite of the two to use, because the whole system is modular: you can take it apart or put it back together without using any tools! The splitter (or riving knife) attaches to the same arbor component as the blade, so no matter how you bevel, and no matter what size blade you use, the splitter always lines up without needing any adjustments.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. We ranked the quietest 3 saws as a 2, and the remaining saws as a 3 and felt none should rank a 1 due to the need for hearing protection.

Welcome to the heart of this website – my selection of the best table saws for several specific needs. You see, it’s impossible to select only ONE as the best for all purposes because a table saw should be carefully tailored to your needs. There’s no point in buying a complex cabinet saw if you’re a beginner, you’re probably better off with a solid benchtop saw. The same goes if you’re a professional, only the other way around.
The stand is collapsible and wheeled like others, but it’s not the gravity-rise style. You’ll have to use a foot to stabilize it while you pivot it up or lower it down. The lower locks are released with your feet and there’s some question about the long term durability of the releases. An open housing design has two major results – motor cooling should be more efficient but it trades off storage for an extra blade. There’s really way too much to talk about here, so check out our full review of this model.
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:

Cabinet table saws are the best choice for full-time professional woodworkers with a dedicated workshop. If you have a spacious shop, these are some of the most efficient, versatile cutting tools you can buy, especially for larger stock. With 3+ HP motors, they’re by far the most powerful machines you can get your hands on. Plus, their heavy, machined build quality gives you a precision and smoothness in your work that really compliments the professional. They have the most effective dust collection systems of any table saw, and durability that can last more than a lifetime.


The Delta Unisaw is a heavyweight in woodworking circles. It’s been on the market for years, and it’s a stalwart through and through. It has a super-powerful 5 HP motor which can blast through the toughest hardwoods and composite materials quickly. It also features one of the most precise bevel adjustments on the market, down to 1/4 degrees! It has a solid, single-cast trunnion which provides excellent vibration dampening, and an extra-heavy case iron base. In short, this is a hulking beast of a machine, and it’s easy to see why it’s been a shop favorite for years.

TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.


Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.

The DEWALT DW745, due to its smaller size, does not have the capacity to use a stack of dado blades (blades designed to be stacked together to make wider cuts, grooves, and notches). It has also been noted that the plastic miter handle is a weak point, and it limits accuracy. There are no available table extensions. It does, however, come with a three year manufacturer’s warranty.
If you are just learning how to sharpen your table saw, you may wonder how to know when to sharpen your saw using your best table saw grinder. You do not want to end up sharpening it too much because that will damage your cutters. It is dangerous to work with a saw that is not sharp enough. Dull cutters tend to catch in the materials and propel the bar in the operator’s direction.
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.
One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
SawStop is the only saw in the group to employ this style fence and they have the best in the group. Ridgid comes in second with a traditional front clamping fence system that has a backside contact point. Its solid construction and wide cast front clamp left us impressed. DeWalt’s came in third with an innovative effort that locks into several points based on where you need it. Rather than sliding along, it stays in place while the rack and pinion system moves it into place. It’s not perfect, but it eliminates a lot of accuracy issues that come from locking the fence out of square on some systems.
But with top quality saws come features that some people may find well worth the extra investment, substantial though it may be, and thus our discussion starts with pricier models. At the top price range for table saws, you can often get a saw with safety technology that will automatically halt its blade the instant it encounters human flesh. (The process literally takes but a few milliseconds.) The knowledge that your fingers and hands are safe from major injury caused by a rapidly rotating, razor sharp blade is more than convincing enough for many people to invest in these technologically marvelous table saws.
When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.
Obviously, given its size, the TruePower 01-0819 isn’t the kind of table saw you’d spring for to take on larger projects that require greater motor power — after all, it’s by no means revolutionary in the torque department. But for those who work with smaller materials or softer wood, the Gino Development TruePower 01-0819 Mini Electric Table Saw is a worthwhile, no-frills buy that’s easy on the wallet and can fit in virtually any space with plenty of room to spare.
As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.
Bosch’s 4100-09 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.

The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.
The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).

The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.


Today's table saws also include riving knives, which ride up and down with the blade when its height is changed, rather than splitters that are fixed in place. The problem with the old splitters was that they had to be removed for certain types of cuts, and users might forget to put them back on before making rip cuts. This increased the risk of kickback injuries, which occur when the spinning blade kicks back a piece of wood toward the user with tremendous force, causing serious injury to any part of the body that's hit.


Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
In other words, a malfunction might mean an injury. This distinction could not be more pronounced in any other job site equipment than a table saw. I have personally witnessed devastating injuries on a number of occasions that could have easily been avoided by the use of safety equipment that comes standard on most brand name saws. Liability for a job site injury can be a serious setback for well established companies, but for small, independent contractors it could mean the difference between business and bankruptcy.
Home Depot sells around 60 models of table saws on its website, and the top models get hundreds of reviews from users. We found four portable saws with ratings of 4.5 stars or better from 250 users or more, and one contractor saw gets ratings just shy of 4.5 stars overall from more than 650 owners. Individual reviews are fairly short and include ratings for quality and value.
What 🤔?? I find it pretty rare to have to re-align the rack and pinion fence on the dewalt, but short of the first time figuring it out, it shouldn’t take more than 5-10 minutes to do. The time savings comes in not having to stick a tape to the fence every time you move it to ensure it’s parallel. I am excited to see other tool manufacturers are using rack and pinion fences now so that there are other options besides the dewalt, namely skil’s latest worm drive ts and the latest hitachi, I’m just not interested in any other fence system on a job site table saw.

The Powermatic 1792001K PM2000 is an award winning cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. The 1792001K PM2000 is the result of years of work and research and hundreds of interviews with woodworkers that offered input which was eventually implemented in the saw. The performance, reliably and safety of this saw are so great, that they actually set a new standard by which all other cabinet saws are judged.


We spent 42 hours on research, videography, and editing, to review the top options for this wiki. Regardless of whether you're a construction professional, a precision woodworker, or a DIY hobbyist tackling your next home-based shelving project, one of these handy table saws will help you get the job done fast. Our selections include models with durable cabinets, powerful motors, integrated fence rails, and even patented safety systems to protect you from on-the-job injuries. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best table saw on Amazon.
Our biggest surprise while running the best table saw review tests was in the cutting power and the quality of cut: There wasn’t much difference among them. All these saws ripped through 3-in.-thick oak without hesitating. We tried this test with the stock blades that came on the saws. Then we repeated the test using a top-quality blade in each saw.
Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.
I also added in a bicycle saddle bag, that attaches easily to the tube frame of the saw. In it, I keep my PPE, and my Grr-ripper push blocks (great upgrade over regular push blocks). I also have a push stick made of wood that was modeled after the plastic one mounted on the back of the saw. The wood one is there now. I read too many stories of injuries after the blade touched the plastic stick, which to me is the whole point of using a stick – to avoid injuries. These things turning to shrapnel seems like a bad idea.
If you’re a professional woodworker, you should expect a standard hookup on any saw. However, you’ll find that no portable table saw does a perfect job collecting sawdust. Since these aren’t enclosed tools like a cabinet saw, there are lots of ways for dust to find its way to your floor and spray around your shop. You’ll want to look for the most enclosed, effective design possible, and pair it with a vacuum system that’s got some heft.
Bosch engineers deserve kudos for the Gravity-Rise stand, and it’s a design some other manufacturers should emulate. Twist one lever, and the sturdy, steel frame folds up or down fluidly to convert from sawing to transport or storage. Eight-inch wheels and lugged rubber tires make this base easy to steer overland or pull up steps. Plus, the base’s stance is wide, giving it sure footing if you are pushing long planks or heavy sheet goods through. It will not tip. But, the stand when erected sets the saw’s tabletop quite high, at 38-1⁄2″. Shorter users may find this to be a bit too tall for comfort.

Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
×