One of the lightest and most compact table saws was also the most stable: Skilsaw. There’s no wheel base to the stand and the outward angled legs provide a wider platform than it may appear against its colleagues. In second place was DeWalt, also offering a wide platform, but without the amount of rigidity that Skilsaw has in their stand. Coming up in third was Bosch with its gravity rise stand followed closely by Ridgid. It’s important to note that none of the professional class table saws had any stability issues inherent to their extension locking—it was all in the stand.
6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side. 

As you can tell, this particular type is in the middle between portable and contractor. Some people can finish their projects with bench top saws, but the ones who can’t usually opt for hybrid saws because they are cheaper than contractor ones. One cannot say they are cheap per se, but it’s a significantly smaller investment in comparison to contractor models.
Located right next to the hand wheel on the front is a panel that features both a power button and a stop switch. The power button helps the motor come to life quickly without requiring that it heat up first, and you can press down on this button to turn the saw off at the end of the day. The emergency stop switch helps you stop the blade in the middle of a project to prevent accidents caused by clothing or skin coming into contact with the blade.
One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.

Overall, the Dewalt's combination blade leaves a slightly smoother finish, but both brands' general purpose construction blades are good enough to start off with. Cross and rip-cut edges were fairly smooth, but users who plan to cut down a lot of plywood will definitely want to invest in a more suitable saw blade. Both saws provided ample cutting power without a noticeable difference in cutting speeds, so we're calling this one a tie.
The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.
Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.
It also has the highest blade speed. This model has a similar 15-amp motor to our other recommendations, but it’s geared for maximum efficiency. The result is a blade speed that’s nearly 1000 RPM better than the Bosch or the smaller Dewalt. Reviewers marveled at how powerful this one was compared to the size of the motor, which seems underwhelming from the outside. It rips right through oak, cherry, and other planks with no lag or burnout. In fact, we’re hard-pressed to find something this would struggle to cut, provided you equip it with the proper blade.
It features an 1850W motor which delivers more than enough power for any heavy-duty task and DIY project. Dewalt is well-known for designing quality tools, and they didn’t disappoint with this particular model either. The fence system offers 610mm of rip capacity. As you may assume, even though it’s a portable unit, you can easily cut large pieces of wood to a particular size.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
There are a few nice conveniences which we don’t always see on affordable units like this. The Grizzly has a built-in miter guide, made from cast iron, which slides easily in the worktop. The left-tilting blade is coordinated with a digital display, which gives you an accurate, real-time readout on your bevel angle as you cut! The motor has a starting amperage of 13, which is safer for your breakers than 15 amp models. There’s a standard 4” dust collection port, and
With both saws offering easy bevel and blade height adjustment, the ease of use comparison focuses mainly on the rip fences. Once the Bosch's rip fence is attached to the table, it moves smoothly across the table when unlocked. But unlocking the fence requires a bit of hand muscle. You can adjust the clamping pressure to alleviate this, but make it too loose and the fence may wobble out of square. Modifying the fence locking lever, or using a cheater bar (such as a push stick) works reasonably well.

If you’re looking to use a wheeled base, you’ll want a standard rectangular unit, not a cabinet with multi-directional extension tables. Double check to make sure the model is compatible with wheeled bases, and make sure you buy your base from the same manufacturer, so you have a guarantee that they’ll work together. No matter what, don’t skimp on your base! Remember that the frame and wheels have to hold up a machine that weighs 1/4 ton or more, so it needs to be incredibly sturdy.
It’s compact. This one is just over two feet in either direction, and just under 14 inches high. It’s easy to fit in the back of a truck, or even on the passenger seat next to you on the way to your jobsite. It’s light, too. Buyers loved how easy this one was to carry around, especially home DIYers who had to set up and take down their units frequently.
As you can tell, this particular type is in the middle between portable and contractor. Some people can finish their projects with bench top saws, but the ones who can’t usually opt for hybrid saws because they are cheaper than contractor ones. One cannot say they are cheap per se, but it’s a significantly smaller investment in comparison to contractor models.
Jet also gives you different choices when it comes to the extension wings. Some customers prefer the cast iron wings because they add more weight and keep the table from shifting, but others prefer the stainless steel wings that are durable and easier to use. No matter which wings you choose, you’ll find that you can quickly and easily attach them to the table’s surface to extend the total amount of workspace you have.

Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
×