Both of these table saws have a port that connects to a shop vacuum for dust collection. The DEWALT features a 2.5” port, while the Bosch has a 2” port. However, neither seems to do all that great a job. The Bosch might fare a little worse as far as the dust port clogging, but the DEWALT has some problems in this area, too. The Bosch is said to spew sawdust on the floor as though there was no dust collection port at all. The DEWALT racks up some complaints about the same problem.
It can seem like plastic is a weight-saver on the part of the manufacturer, but it’s really a cost-saver. You shouldn’t accept shoddy build quality in the name of getting a lighter machine. While no portable unit will include heavy cast iron components like a cabinet table saw, you can find metal alternatives that offer rugged, long-lasting build quality. Instead of plastic, look for aluminum.
6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
It’s the safest of the three by a long, long shot. SawStop became a major brand thanks to a feature that they’ve named their brand after: an accident-proof stopping mechanism for the traditional table saw. The innovative brake system on this model is the best on the market at detecting flesh and stopping the blade immediately. It’s a sure bet for saving fingers or worse injuries in the workshop.
Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.
The Delta Unisaw is a heavyweight in woodworking circles. It’s been on the market for years, and it’s a stalwart through and through. It has a super-powerful 5 HP motor which can blast through the toughest hardwoods and composite materials quickly. It also features one of the most precise bevel adjustments on the market, down to 1/4 degrees! It has a solid, single-cast trunnion which provides excellent vibration dampening, and an extra-heavy case iron base. In short, this is a hulking beast of a machine, and it’s easy to see why it’s been a shop favorite for years.
That’s why we’ve created this handy guide! As usual, our trusty team have taken a comprehensive look at all the options out there. We’ve looked for portable units that don’t sacrifice power or accuracy for their small size. You’ll find our Top Three recommendations below, along with a few additional choices for new woodworkers and demanding professionals.
We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.
There’s a lot to like about this saw. The stand is easy to set up and very sturdy. We like the smooth-operating table extension and the blade guard’s hold-up feature and ease of installation. The only downside we found is that the motor mount is less rigid than those on the other saws we tested. We suspect that’s why the cut quality on our torture test was not as good with this saw.
These tests and evaluations are very difficult, take a lot of time, and ultimately limited in scope as we’re not a professional testing company and we’ve got limited time to evaluate the tools. We cannot do longer term testing that would shed light on durability and we can’t possibly test every application that you might use of one of these saws for. However, we feel comfortable that all the table saws in this Head-to-Head are good saws and our testing helps bring to light pros and cons for each saw.

Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
×