From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.
We’re impressed with how much thought SawStop have put into all the features on this model. It has an extra-large bevel gauge ruler on the side of the cabinet, tool-free, modular guard system, and compatibility with innovative wheelbases which don’t add noticeably to the SawStop’s height or footprint. It also has beveled edges to protect your materials, a very nice touch that our other recommendations don’t have. All in all, it feels like a tool designed by people who use one of these units on a regular basis.
A table saw has two main ways it can seriously hurt you. One is obvious and that is having any part of your body come into contact with the blade. Any table saw you are seriously considering should have a blade guard installed. The clearer the better. And make sure you leave it on. The blade guard can’t do its intended job from a workbench or shelf.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
While we rotated the plate, we recorded the maximum reading on the dial indicator. We validated each maximum reading by running the test for a second time and noting that the readings were consistent. TBB also noted that as we performed these tests on all eight saws, the maximum readings occurred at different parts of the plate along its rotation. Because the max readings were in different and discrete parts of the calibration plate, TBB had a very high level of confidence in the flatness of the calibration plate, itself.

While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.
The type of woods you cut will determine how powerful a motor and how fast a blade speed you need from your portable table saw. If you’re going to be dealing primarily with thinner boards and softwoods, you don’t need anything hugely powerful. If you’re working with hardwoods or thicker softwood stock you should look for a more powerful motor. Likewise, if you’re only an occasional woodworker, you needn’t worry about finding a motor that won’t burn out.
These saws are the most difficult ones to categorize. The simplest explanation would be that they are somewhere in the middle between contractor and industrial cabinet saws. They are driven by an inboard belt motor. These units usually have open leg stands, but there are some models with closed ones – hence the whole confusion and difficulty in categorizing.
How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.
Table saws will continue to be popular and much sought after tools in any workshop or construction site. There are many terrific styles on the market which is why it is important to do some research and look at the reviews provided here as well as the tips contained in this guide to help you choose the right table saw for your needs, whether you are a professional or a DIYer who loves to work in the workshop making things for enjoyment.

If you work with wood in any capacity, chances are you rely on a table saw to make clean, accurate cuts. But when your good old saw goes to the big toolshed in the sky, it’s time to opt for a replacement. Before you dish out your hard-earned money on the first model you come across, remember that a table saw is a big investment, so it’s in your best interest to look into the many technical specifications of each option before you settle on a final purchase.


If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.

However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.

If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.
It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
You will agree that your ability to hold, controlling and manipulating the saw largely depends on your strength. Since small table saws are lightweight, you should go for a powerful table saw so as to avoid fatigue during small jobs. This also means that if you are working in a forest for a whole day the light weight is of great importance it also helps reduce fatigue. When shopping for chainsaws ensure the saw balances well in your hand. You should also ensure that you can easily shift the saws grip from hand to hand without losing its balance.
The miter gauge gets an “its fine” grade. Ok to support a narrow piece for a crosscut, but not long enough to do much more than that. I upgraded to an Incra miter 1000SE and never looked back. Although a crosscut sled is pretty easy to make (and I highly recommend getting one) I picked up an Incra Miter Express sled for real cheap at a garage sale, so I am happy to use that.
It’s sturdy. This unit also has a metal roll cage frame all around, which helps it handle the rough and tumble of travelling to worksites on a regular basis. It has a locking mechanism to help it stay securely on stands. We’re also super impressed by how well-made the adjustment knobs feel on this one. Buyers reported using this one for several years with no issues.
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
×