While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.
The safety brake feature is a real step forward in engineering, but it does have a few downsides. The aluminum brake works with single-use cartridges, so you’ll have to replace the cartridge if you trip the sensor. Likewise, the impact of the brake, stopping the blade in milliseconds, will destroy your blade, so you’ll have to replace that as well. It’s a small price to pay for keeping your fingers or limbs, but it’s probably a good idea to stock up on cartridges and blades
Bosch GTS1031 10 in. portable jobsite table saw is powered by a 15 Amp motor that allows this table saw to rip through any lumber or hardwood quickly and easily. Bosch’s Smart Guard System provides added control while cutting, SquareLock Rip fence ensure consistent and accurate cuts, and an all steel base provides added durability. Oh yeah, and we forgot to mention the price. This is the most affordable table saw on our list!
Patrick – Thanks for the feedback. Trust me, I wish we could spend more time on every aspect but we spent hundreds of hours as it was. I can tell you that the rack and pinion fences are much better than the standard fences of the past. Our entire group felt strongly that we’d prefer the rack and pinion on all the saws. We felt the Ridgid and Delta fences were the least impressive of the standard type.
Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
There’s also a secondary flip-down fence which allows you to make narrower rips. We love this feature, which should really become industry standard in the near future. It helps you make smaller cuts without needing to have your fingers close to the blade. Reviewers loved it, and said they found themselves using the feature much more frequently than they’d anticipated.
It’s easy to use, quite safe, and most importantly – it’s a high-quality piece of equipment for a more than reasonable price. If you don’t like what you see, don’t hesitate to read some of our other reviews, there might be something of interest for you. As far as this particular model goes, it should turn out to be a worthy and cost-efficient investment. In the end, it all comes down to your personal preferences.

For those of you who are looking to up your DIY game but don’t have enough capital to make the Dewalt DW745 happen for your home shop, this Craftsman is a decent budget choice. It’s powerful, lightweight, and extremely affordable. We don’t think you should expect too much from this one, though, since it has a very light table and a fence that won’t line up quite as precisely as you’d need for furniture-making or professional-grade projects. It’s cheaply-made, and doesn’t have as user-friendly a design as our other choices. For the home carpenter, though, this should do the trick for all your basic framing cuts.
Jet also gives you different choices when it comes to the extension wings. Some customers prefer the cast iron wings because they add more weight and keep the table from shifting, but others prefer the stainless steel wings that are durable and easier to use. No matter which wings you choose, you’ll find that you can quickly and easily attach them to the table’s surface to extend the total amount of workspace you have.
PLEASE EXCUSE THE PICTURE, LUMBER JOCKS REQUIRED ONE. I AM AWAY FROM HOME AND COULDN’t RUN OUT TO THE GARAGE TO SNAP A SHOT. I am writing a review of my Bosch saw after a few months of use. I bought this saw last November after my Ryobi saw up and died during a project. I looked at several saws in the $600-$800 range and narrowed it down to four options. The Bosch and DeWalt jobsite saws, and the Delta and Ridgid contractor saws. My requirements were in a realativly compact saw th...
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.
First, consider the types of cuts you’ll need to make, and which types of stock you work with on a regular basis. Think about the largest rip cuts you need to make, and get a cabinet saw with a suitable max capacity for rips. Find the thickest stock you need to cut, and make sure your new machine has a high enough depth capacity to make the cut cleanly. The larger your average stock, the larger a workspace you’ll need on your new cabinet unit. It’s also a good idea to think about bevel and miter cuts which you’ll be making on your table saw. All of our recommendations have the capacity for both, but some come with miter gauges and others don’t.
With a cutting speed of at least 4,500 RPM, nothing will hold you back from getting the job done in minutes. Hitachi job site table saw is designed to give you freedom in your work and the ability to manage your time. Keep every minute accountable by investing in the right tools for your workshop. However, during different occasions, you will have different materials both in size and texture. During such moments, you will require adjusting the fence to accommodate your material and cutting style. This job site table saw is designed with an adjustable feature to ensure your precision and accuracy is not compromised. The low power consumption makes it easy for you to maintain the saw and enjoy smooth and accurate results at no extra cost. When it’s not in use, the table saw has fold and roll stand that guarantees you space saving and convenient storage. The foldable design also makes it easy to transport from one place to the other comfortably.
With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.
We’ve used $2,000 as our minimum spending threshold on these models, because that’s what we’ve found you have to pay for a cabinet model with all the features we consider essential: a precision-machined cast-iron worktop, a versatile fence on sliding tracks, a 3 HP motor with belt drive, an all-steel cabinet, a cast-iron trunnion support, and machined flywheels to adjust the blade settings.
The miter gauge gets an “its fine” grade. Ok to support a narrow piece for a crosscut, but not long enough to do much more than that. I upgraded to an Incra miter 1000SE and never looked back. Although a crosscut sled is pretty easy to make (and I highly recommend getting one) I picked up an Incra Miter Express sled for real cheap at a garage sale, so I am happy to use that.
One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.
SawStop is the only saw in the group to employ this style fence and they have the best in the group. Ridgid comes in second with a traditional front clamping fence system that has a backside contact point. Its solid construction and wide cast front clamp left us impressed. DeWalt’s came in third with an innovative effort that locks into several points based on where you need it. Rather than sliding along, it stays in place while the rack and pinion system moves it into place. It’s not perfect, but it eliminates a lot of accuracy issues that come from locking the fence out of square on some systems.
From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.

As with the smaller Dewalt we’ve recommended, this one has very inconsistent quality control on the table. Some reviewers cited units with bowed, funky surfaces, while others got units that were perfectly flat. that’s a flaw of the molding process. We also have a bone to pick with Dewalt as far as the coating on these. While we understand that the coating is supposed to help wood slide better, it just doesn’t seem to last very long or hold up well. It also has the same flawed warranty coverage. We’d recommend purchasing add-on coverage.
As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.

The purchase of a table saw is no doubt a big investment. But there is a lot of flexibility in this class of tools to find one that fits in with your budget and your wants. Make sure to take into account how you will need to use the tool and where you will need to use it. Heavier models will be sturdier but they will also require more effort to load up when you need to.

One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.


The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.


More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.
×