It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
Some of the key factors that every woodworks person will ensure are accurate and will not compromise our performance and quality of the saw. With grizzly G0690 cabinet table saw, you will get all these in one packaging. The table saw has a riving knife that will automatically switch to action following the same blade tilts for better performance. Its made of high quality and heavy duty material to guarantee that it will last a lifetime.
But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.
This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
Setup was nearly as simple as SawStop’s with just a narrow margin between them. We only needed to attach the handle and bolt the saw down to the stand. The stand is a gravity rise style, but requires you to bend down to ground level for collapsing and extending it. It’s a reasonably solid platform, though a lot of movement throughout the day will leave your back sore.
Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.

You will agree that your ability to hold, controlling and manipulating the saw largely depends on your strength. Since small table saws are lightweight, you should go for a powerful table saw so as to avoid fatigue during small jobs. This also means that if you are working in a forest for a whole day the light weight is of great importance it also helps reduce fatigue. When shopping for chainsaws ensure the saw balances well in your hand. You should also ensure that you can easily shift the saws grip from hand to hand without losing its balance.
In layman’s terms, a miter gauge is a device that allows users to set up the angle of the material being cut with a table saw. And while most table saws come with built-in miter gauges, others, well, don’t — which is why the Kreg KMS7102 Table Saw Precision Miter Gauge System is invaluable. Whether you’re replacing an old, worn-out gauge or putting it to use in conjunction with a table saw that didn’t come with its own proprietary gauge, the KMS7102 is specially designed with precision in mind. After all, accuracy is vital to successful woodwork.
To adjust blade height you simply operate the elevation wheel located on the front of the saw, and the angle of the blade can be set through a switch which is behind the wheel in case you want to make bevel cuts. The angle can be set anywhere between 0 and 45 degrees, and once you’ve adjusted the bevel angle it can be locked into place using the handle.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.

If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.
×