About three paces from where I tested these portable table saws sits my late-model cabinet saw. As a serious woodworker and magazine editor, I can’t imagine not having it. Its powerful 3hp motor, spacious cast-iron tabletop and almost hair-splitting precision makes most other saw options pale by comparison. But all this said, a cabinet saw isn’t everything. The thought of moving that behemoth down the steps to a basement shop sends chills up my spine. I sure can’t toss it into a car trunk to help a friend down the road. My saw takes up a huge footprint of shop floor, and it cost a small fortune. I don’t know of any stationary table saw that sells for less than $700 new these days, and that can empty the coffer of a modest tool budget.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
The Shop Fox W1819 also comes with a miter fence with flip stop which provides excellent workpiece support and is great for longer workpieces. As for the flip stop, it’s going to be very useful especially when wanting to make several cuts of the same width. If you want to cut longer workpieces, you can also flip it out of the way and then pivot it back down in order to make more cuts at the cutting width of your choice.
The quality of cut is as good as I can get with a cabinet saw, with one key exception: It takes more time to get it set up just right. There isn’t as much lead up before the blade, so getting the wood to track true is harder with less fence. I kind of wish they had backed the blade up an inch or two assuming they couldn’t make the saw a bit deeper.
In my opinion, the Bosch is the clear winner here. While both of the saws are technically portable, the Bosch’s wheeled, easy to set up stand will get you to work quickly, without the need to keep track of multiple parts and accessories. While the DEWALT is much lighter, that difference is negated by the fact that you will be forced to carry it from the vehicle to where you will be using it, rather than pulling it behind you like wheeled luggage.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
We absolutely love the Dewalt DWE7491 that we recommended as our top quality choice above. It’s a powerful, precise workhorse that can handle nearly any cutting job. However, times are changing fast, and workplace safety standards are increasing just as rapidly. If you’re a professional who wants to stay on top of your code, you should consider getting a unit that’s equipped with a flesh-detections safety system.
Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.
Portable table saws, or “jobsite” models, as they’re often called, are your best bet for working with larger stock or longer cuts on the go. These units provide the cutting width and depth of a big table saw in a compact, portable package that’s easy to throw in the back of the pickup after a day’s work. They’re ideal for pros working on smaller jobs, handymen who need a basic table saw that won’t break the bank, or home DIYers looking for a tool that’s easy to pack away during the workweek.
Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.
Table saws can be tougher to evaluate on paper since they don’t include torque measurements. Each of the table saws we tested have 15 amp motors, but vary widely on no load speed. The ones with lower RPM values are bleeding off speed in exchange for torque. While the right balance is always tough to achieve (and is a moving target with every new motor development), here’s where each saw prioritizes speed.
The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.