Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.
The obvious starting point for an analysis of which saw is best suited to the needs of a given person (or company, school workshop, and so forth) is the budget at hand. Even the most affordable table saws of a quality meriting serious consideration cost more than 200 dollars; such units are small but still capable of many tasks. The top of the line table saws come with price tags topping out at well over 3,000 dollars and can handle almost any lumber you would ever need cut and then some; more often than not these mighty saws are more tool than needed, so to speak.

After cutting a bunch of wood with this saw, we really liked the balance of power and portability of Bosch GTS1031 – and I think that’s what this saw is all about. For raw Performance, the unflappable motor-blade combo earned a stiff 8/10 in our tests, while its affordable $399 price tag put it at a solid 9/10 in our Value scale. Sure, you can get cheaper portable table saws, but you’ll find it a challenge to track down the combination of power and portability the Bosch GTS1031 offers. Bosch’s gravity rise-equipped 4100-09 remains a compelling alternative or those wanting an integrated stand. It occupies an additional 15″ in width and 8″ in length and is a full 3.5″ taller. But it only tacks on 8 pounds in weight. If you’re cutting larger pieces of wood or need a saw with a stand, the 4100-09 may be your baby, but the new Bosch GTS1031, with its “toss it in the truck” form factor is our new sweetheart tool. While it has an available GTA500 folding table stand accessory, the real advantage of this saw is it’s stand-free portability – so don’t make it into something it’s not. After using this tool, we think you’ll want to take it with you, as-is, just about everywhere!
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
A lot of the modern table saws nowadays will have a dust collection port where you can hook up a vacuum or extraction system to it. We would always recommend that you purchase a table saw with a dust port, always check the size of the port to make sure it fits with either your vacuum or your extraction system, or you can always modify something to make them fit.
Dust capture from this saw is pretty bad. I was shocked that a European brand would ignore the dust collection to this extent – at least I was until I discovered that their version of the 4100 does have quite a few more pieces that help pull most of the dust from the airstream. There is a plate that encloses the rear around the vacuum port and a bottom grid that allow airflow to the motor while still shaping the airstream to drive the dust to the vac. I added the plate, but decided against the grid. Instead, I added a sheet of ¼” plywood and put a 4” vacuum port in it that I hook up to my dust collector. I also replaced the blade guard with the European version that has a dust port built in. Minor upgrades, but dust capture has gone from terrible/non-existent to pretty acceptable. Bosch also sell a bag that will capture whatever dust would get tossed out the back of the saw, but that isn’t much, so I consider it a waste. I did buy it, and it works well on other tools, but it is not IMO a must-have for the 4100

Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
This article is the place to start, and then you can take it from there. My table saw buying guide has all the essential information on table saws you will need, like their classification based on size, portability, motor type, blade size, and the features they come with. You will encounter each of these terms in all the product reviews, which is why you shouldn’t skip reading it.
But with top quality saws come features that some people may find well worth the extra investment, substantial though it may be, and thus our discussion starts with pricier models. At the top price range for table saws, you can often get a saw with safety technology that will automatically halt its blade the instant it encounters human flesh. (The process literally takes but a few milliseconds.) The knowledge that your fingers and hands are safe from major injury caused by a rapidly rotating, razor sharp blade is more than convincing enough for many people to invest in these technologically marvelous table saws.

We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
With that said, the Dewalt DWE7491RS (another jobsite saw) has an amazing fence. It also has a greater ripping capacity – so if this additional functionality is more important to you than portability, it might be something to consider. Although keep in mind that it’s also 30lbs heavier, and the stand is much worse than that of the Bosch (which we’ll discuss later in this article).
I’m trying to replace some lost tools for a doctor inflicted, lawyer cowardice sustained injury. I’ve been a woodworker for more years than I might imagine I am comfortable with saying simply for it seems to have been bestowed upon me from birth. The only comment I have is a general comment. As I’ve noticed from about 20 years ago being introduced do officially being educated at a local community college, everyone there had prestige rights attached to it, a couple of cabinet makers I worked for did also that Porter Cable was the Cadilac of woodworking tools. Well, China… Read more »
Some table saws go one better than a splitter. Splitters are fixed. They do not move along with the blade. It also needs to be removed if you’re making cross-cuts or dado cuts. A riving knife, on the other hand, is fixed to the same part as the blade. This means it can move along with the blade. Riving knives don’t get in the way either so this is the best option.
At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.
The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
Setting up both saws was quick and easy, since their factory-adjusted blades and fences were square and parallel to the tables' miter gauge slots out of the box (this is one of the reasons to buy a $350 table saw over a $100 one). Both saws had similar setup procedures: Attach the fence, raise the riving knife, attach anti-kickback pawls and attach the blade guard. There is no on-board stowage space for the DW745's rip fence, but this does not really affect the setup time or effort by much. 

Portable table saws, or “jobsite” models, as they’re often called, are your best bet for working with larger stock or longer cuts on the go. These units provide the cutting width and depth of a big table saw in a compact, portable package that’s easy to throw in the back of the pickup after a day’s work. They’re ideal for pros working on smaller jobs, handymen who need a basic table saw that won’t break the bank, or home DIYers looking for a tool that’s easy to pack away during the workweek.

It’s the best of the three at keeping your shop clean. The SawStop has a blade guard and arbor enclosure that’s engineered and sculpted to maximize vacuum suction at the cutting edge. Plus, the guard hugs tightly to the blade, and like the Jet, opens at each side so that whichever way you’re cutting, dust goes down the vacuum chute instead of off to the side of your workspace. It’s lab-tested to be up to 99% effective, and it’s certainly the most impressive dust collection system we’ve seen to date.

First off, consider how often you’ll put your table saw to use. If you work in the fields of contracting or carpentry, there’s a chance you’ll be using your new machine pretty often — so you may as well invest in a more expensive, heavy-duty table saw that’s sure to last longer than the average model. On the other hand, hobbyists and weekend woodworkers won’t need a pricey piece of machinery — a more compact and inexpensive model should do just fine, especially if you’re only working on smaller projects like birdhouses and DIY wooden models.
I like the clever design of the stand on this saw which allows it to collapse or open by operating a single lever. The unit has two transport wheels which allows for easier relocation and the stand doubles as a pulling handle. It measures 39 x 30 x 20 inches which makes it pretty compact. The distance between the floor and the work surface is 37.5 inches. To make the stand as durable and corrosion-resistant as possible Bosch has given it a powder-coat finish.
The maximum depth of cut on a saw tells you how thick of a material you can cut through cleanly. Be careful when you’re looking at depth of cut ratings, since you’ll usually find two separate specs listed. One is for cutting at 90 degrees, the blade’s normal setting, and one is for cutting at a 45 degree bevel, which is generally the furthest a table saw blade will pivot. Most of us will only need to be concerned about the 90-degree rating, but if you cut lots of angles, you should check the 45 degree rating as well.
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.
To avoid such scenario, you can take a moment and check our full reviews out. We offer more than enough insight into the capabilities of particular models we consider are worth checking out. Therefore, if you’re in a dilemma about which table saw to buy; don’t hesitate to refer to this article. The more you know about a certain unit, the fewer problems you’ll have when the moment of purchase comes.
The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.
A magnetic switch is also good from a safety standpoint but may not be necessary on these smaller versions. A magnetic switch prevents the saw from starting back up if it loses power during a power outage. Basically, the power outage will turn off the saw. This is good because if for some reason the power were to come back on when you were not near the machine, the material could be shot out of it or damage the saw.
It’s also a great table saw in its own right. This one has a wide, cast-aluminum worktable, and an out-feed extension thrown in as well. It has a 4 HP motor which cranks out lots of power, and it’s balanced by a soft start and automatic speed control like on the Bosch in our Top Three. It has wide rip and bevel capacities, plenty of alignment adjustments, and a robust build. Plus, it comes with a gravity-assist wheeled stand thrown in as well.

Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
The quality of cut is as good as I can get with a cabinet saw, with one key exception: It takes more time to get it set up just right. There isn’t as much lead up before the blade, so getting the wood to track true is harder with less fence. I kind of wish they had backed the blade up an inch or two assuming they couldn’t make the saw a bit deeper.
The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.

In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.


You will agree that your ability to hold, controlling and manipulating the saw largely depends on your strength. Since small table saws are lightweight, you should go for a powerful table saw so as to avoid fatigue during small jobs. This also means that if you are working in a forest for a whole day the light weight is of great importance it also helps reduce fatigue. When shopping for chainsaws ensure the saw balances well in your hand. You should also ensure that you can easily shift the saws grip from hand to hand without losing its balance.

×