You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
The body of the blade is made from hardened steel, helping to extend the lifespan and keep up with the tooth quality. The kerf is a crazy-thin 0.098 inch—narrow to keep the cuts fast by reducing the amount of material that needs to be removed. Like most Diablo blades, you’ll pay a bit of a premium up front, but the blade lasts so much longer than others on the market that the cost per cut is much lower.

Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. We ranked the quietest 3 saws as a 2, and the remaining saws as a 3 and felt none should rank a 1 due to the need for hearing protection.

The DeWalt DWE7499GD table saw earns a third place finish in the safety category thanks to their GuardDetect technology. This doesn’t prevent you from using the saw without the pawls and blade guard in place, but it does require you to physically indicate you are aware they’re not in place. Ideally, this gives your mind one last opportunity to consciously note the additional care that needs to take place before cutting.

However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.


I’m not crazy about one feature, and it’s common to three of these five saws: to tip the blade, you unlock a lever behind the blade height hand wheel, then swing the undercarriage up to the angle you need before re-locking the lever. A geared bevel control would make this process a little easier. But, once tipped, Bosch held its angle setting well through my test cuts.
A dedicated writer and communications professional spending his days lost in the intricacies of both proposal and freelance writing. When not sharing the knowledge of both fully and self-insured medical benefits to employer groups of all industries within California, Jeff Newburgh can be found at home spending time with his family and 3 dogs, pondering the next chew toy to be thrown, while kicking back and relaxing with a nice glass of red wine.
This woodworking website has tons of information about how to use a table saw: choosing blades, cutting joints, safety features, and more. However, we found only five actual product reviews, none more recent than 2013. Although these individual reviews are hands-on, they don't put saws through any specific, detailed tests. There's also no direct comparison between saws and no formal rating system.
As with our other models, it takes some assembly. If you get one of the extended models, which we’re recommending here, you should plan to cut the rails down to size before finishing installation. It’s simple to do if you’ve got a good miter or bandsaw, but it is an extra step. With that said, many reviewers complimented the SawStop’s well-written and helpful manual, which made installation significantly easier than other units.
We’ve used $2,000 as our minimum spending threshold on these models, because that’s what we’ve found you have to pay for a cabinet model with all the features we consider essential: a precision-machined cast-iron worktop, a versatile fence on sliding tracks, a 3 HP motor with belt drive, an all-steel cabinet, a cast-iron trunnion support, and machined flywheels to adjust the blade settings.
Other than getting a cutting tool that will lighten your work, investing in an item that will ensure you are satisfied by its construction, performance and longevity are the desire of every customer. DEWALT understands better the needs of various customers and has been in the business for a long time. The many year’s experiences have given the company trust in customers. Therefore, they manufacture strong tools with high performance and back them with a sustaining warranty. The table saw is designed with a portable style for use in any room comfortably.  15 amp, gives a powerful and consistent performance to ensure you don’t have pending jobs on various days. The large rip capacity makes it easy for you to cut even large materials comfortably. When using this saw, all you need is to keep your eyes open, it has a guide system that will provide accuracy and precision in your work automatically.
The simplest way to find out what size your table saw needs or indeed if you’re buying a special size is to consult the table saw user Manuel. I would make sure you do this as often there are many things in modern tables saws that could affect the blade size and type. This is because modern saws have many different amazing and varied features, things size blade guards, special safety mechanisms and arbor sizes etc. With the We recommend you spend some time reading your manual in detail to avoid possible issues
Optional portable table saw stands are available for both saws. (Bosch's stand is called the GTA500; DeWalt's is the DW7450.) The Bosch features tool-less connection (after initial assembly), while the DeWalt requires the attachment and tightening of four bolts through the DW745's bottom roll cage— though it's nothing a few after-market knobs couldn't fix.
If you’re going to be transporting your unit regularly, you should aim to keep weight to a minimum. Look for something lightweight, with convenient carrying handles, or a stand that can be wheeled around dolly-style at the worksite. Conversely, if you’re only going to be using your portable saw occasionally, you can probably stand a bit more weight.

The Craftsman table saw is one of the most compact of the bunch when it’s folded up. And if you can get it for the sale price of $260, it’s also the cheapest of the best table saw options. The blade guard and anti-kickback pawls are identical to the Porter-Cable and are the hardest of any of the saws to install. And they are the only two blade guards that don’t have a feature to hold them out of the way when you’re adjusting the blade or setting up the cut.
Sometimes picking a “Best Bet” is a real tossup, but not this time. While Bosch’s 4100-09 doesn’t disappoint, and DeWALT has what seems to be a bulletproof portable, I think RIDGID’s R4510 table saw really shines. Its sturdy workaday features, powerful motor and well-designed stand show that portability doesn’t have to mean compromise. This is an excellent woodworking choice for 10″ portable table saws.
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.

It’s heavy-duty. Like all great cabinet saws, the Grizzly is built from parts that can last a lifetime or more. It has a cast-iron table, that’s precision-ground to be exactly level, with no warps or imperfections. The trunnion supports holding up the motor are also solid cast iron, which means that they don’t translate much vibration to the work surface at all. The paint on the cabinet and extension frames is powder-coated, and the miter gauge and riving knife are solid steel. Both extension table surfaces are made with a coated, engineered composite, which stands up well against dings or scuffs.


A gauge will allow you to make very detailed cross and angled cuts. This is a bit of kit that you need to research in great depth as it can make or break the accuracy of your cuts and angles. With a good gauge, you can check blade height, blade angles, miter angles and much more. For further reading checkout Wikipedia’s table saw page and for in-depth air compressor reviews.
The large cutting table surface of the Bosch 4100-09 Worksite Table Saw is roomy enough to handle large work pieces, giving you a ripping capacity of 25”. This is a really great feature if you plan to use the saw to rip solid or plywood panels, or other large materials. I use my table saw primarily for ripping sanded plywood panels for use in cabinetry, and many of my projects would be impossible with a smaller capacity saw. The rip fence glides across the saw cutting table, so you can actually use it with one hand, and locks in place for safety and accuracy. The DEWALT DW745 Job-Site Table Saw offers a 16” cut, considerably smaller than the Bosch. It is perfectly adequate for most application, such as ripping dimensional lumber and small trim applications. The type of materials and work pieces you expect to be cutting are a determining factor in your choice of table saws. If you plan on tackling any large scale projects in the future, the rip capacity of your saw is definitely a feature that you should take into consideration.
If you need to move your saw around, it comes with a table saw stand that you can put up and down with ease. Fashioned from aluminum pipes with wheels that can handle uneven terrain, move around site without breaking your back. As well as its user-friendly nature, the stand can be stored away vertically so it’s a real space-saver whether at home or on the jobsite.
Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.
As for my blades, I replaced the blade that came with the saw right away. It is terrible and would have been better to be not included at all. I replaced it with a Freud industrial 24 tooth glue-line rip blade and a Freud Diablo 80 tooth plywood and crosscut blade (I find it easier to just buy new plywood blades since the glue does a number on them, not to mention the wear and tear caused by MDF). As an all-around blade, I keep a 50 tooth Tenryu Gold blade. It is quieter somehow, and does a cut almost as good as either the rip or crosscut blade. Great for making quick cuts without always changing blades. I will use it for most ripping, but will switch to the ripping blade when I have a lot of ripping to do, or will be going thicker than about 1.5” in hardwood.
Contractor units are the next step up from portable (or jobsite) table saws. A contractor table saw has a worktop and motor assembly that looks a lot like a cabinet model, only it’s missing the cabinet! Contractor units aren’t quite as portable as a job site saw, but they’re about half the weight of a cabinet saw. They pack a lot more power than a portable unit, and their cutaway stands make them fairly manageable for folks who have helpers to assist in getting the saw off the truck and set up at the site.
The Grizzly G0690 is a very unique and powerful table saw and each part of it says performance and quality. With a 3 HP, 220V, 3-phase Leeson motor, heavy cast iron trunnions, wings and table to its triple belt drive system, this model should definitely last you for a lifetime. It’s not only its impressive build quality that’s going to strike you about it, but also its other features that include a four inch dust collection port, a T-slot miter gauge, a magnetic switch, but also heavy cat hand-wheels, riving knife and camlock T-fence. If you’re a professional who’s been using cabinet tablet saws for a quite a while, you’ll immediately appreciate the quality of the Grizzly G0690.
Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.
A riving knife is a piece of metal that comes included with your new saw. It’s shaped like a surfboard fin. Sadly, not all models come with this crucial part. If you purchase a model without it, make sure you design one for yourself as soon as possible. The construction of this piece is not a big deal at all; you can cut the shape in a matter of minutes and install it. Its purpose is to prevent the wood and debris from getting caught in the back of the blade which consequently kicks back thus jeopardizing your safety.
There were really two major performance considerations we wanted to look at to help determine the best portable jobsite table saw: cutting power and dust collection. Power is an obvious choice. We want to make clean, straight cuts, but we don’t want to spend all day making them. Any saw can be calibrated to be straight and accurate, but some have to be babied more than others to get professional results.

The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.


Our table saw review quickly showed that today’s portable table saws are light-years ahead of the small-saw offerings from a decade ago. They feature big-capacity cutting, greatly improved safety features and attached stands for easy setup. And saws in the upper price range rival stationary saws in accuracy and quality of cut. We limited our review to saws that included a stand with wheels and ones that could rip at least 24 in. wide, only the best table saw for our readers!
The Grizzly is our top choice for folks who need lots of room to work, plain and simple. Thanks to its dual extension tables, this one has the widest rip and fence capacity of the three units we’ve reviewed here. We also love that it makes full use of the space under the worktops, so you’ll get plenty of storage room to make up for its larger footprint.
There are several types of table saws. The types of jobs or projects you plan to use a table saw for will determine which type you buy. If you want a saw you can take from job site to job site and store it easily, then you will need a table saw that is made to be portable so that it can be easily transported to the job site. Of the portable or work site table saws on the market today, the Bosch 4100-09 10-Inch Worksite Table Saw with Gravity-Rise Stand and the DEWALT DW745 10-Inch Compact Job-Site Table Saw with 16-Inch Max Rip Capacity are two of the most popular.
More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.
×