Table saws can be tougher to evaluate on paper since they don’t include torque measurements. Each of the table saws we tested have 15 amp motors, but vary widely on no load speed. The ones with lower RPM values are bleeding off speed in exchange for torque. While the right balance is always tough to achieve (and is a moving target with every new motor development), here’s where each saw prioritizes speed.

so.categoriesWithItems ='8003,8002,8005,797,8007,696,8009,793,8011,8010,8013,750,8015,8014,833,823,825,8023,841,8017,2669,470,8041,430,8044,8047,263,8048,8050,306,8051,8053,5954,8055,8054,5957,8056,166,8059,39936,39934,39935,508,8025,5960,139891,139893,8030,566,8031,139905,8034,8033,8035,649,647,8038,661,491149,8742,505663,491151,505665,8277,143,8278,2234,8280,1224,2310,8285,8287,1222,116,6237,8292,8293,8294,8295,8296,8297,8298,8299,8300,8301,139847,139871,9022,39752,39751,39753,39754,997,8077,1022,1032,1025,8082,994,8084,139649,941,944,6471,910,8085,8087,1014,914,8090,8092,1258,8094,139687,8805,39895,39894,39896,39897,8063,224,8064,8065,5956,5959,429,39909,39908,39910,8130,5941,8131,902,1196,8137,8138,8141,8143,8142,8144,8145,1416,8148,8150,8151,1554,1422,8167,8163,8172,8174,8173,8182,8179,8183,39667,39665,469559,37938,469561,469563,37941,37940,37943,37942,37945,37944,37947,37946,3,8185,43,23,35,8191,8194,8195,1642,8196,8199,8200,139409,139411,452623,8203,8202,8204,8205,8206,8209,8210,139437,1299,1664,8216,8217,139455,139459,39703,39702,39704,108845,108843,8112,8111,8116,8114,8117,8115,8118,8106,8105,8107,8108,8109,8120,1132,8121,8122,8123,8126,6269,8221,681,8222,8220,8224,2584,8226,2575,678,662,2593,663,675,843,1699,8235,1805,8238,5980,8241,8244,8246,8247,5987,8248,8250,2614,6517,8253,8262,1307,139301,8264,187,8266,8265,8268,8267,8270,8269,8272,8271,8273,8274,39820,39819,108974,108972,468779,108975,139363,139359,139371,139369,930,928,2804,8101,919,8103,8102,39766,39765,139783,139767,108849,108848,108851,108850,140169,140167';
SawStop has an excellent stand and they’ve cleverly hidden the tool/miter/riving knife storage box under the side extension. Move the table extension and the box presents itself. Like DeWalt, two riving knives come with the saw—one with safety guards and one without. This keeps you from wondering how the pawls and guard go on the riving knife. Blade height fully adjusts with only one turn of the wheel. Not everyone was on board with this, citing less accuracy for dado and rabbet cuts. In the end, we showed we could be as accurate on the height as any of the other saws, so it’s a win.
The cabinet also has a few other safety features that set it on a level above the Grizzly or Jet. There’s an extra-large, paddle-style power switch which you can easily press with a thigh as well as a hand. The guard works tightly against the blade, so that you have all the workspace you need without sacrificing safety. The riving knife prevents kickbacks, and the left-tilting bevel feature prevents binding.
In recent years, there has been a cloud of controversy surrounding the inherent safety issues surrounding the table saw. SawStop developed a flesh detection technology that pulls the blade below the table surface 3 milliseconds after coming into contact with skin. It really created a new class of table saw that, as of June 1st, finally has some competition in the form of Bosch’s REAXX.
Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.

Ridgid notches a third place finish as the only saw to include an independent blade height lock. The adjustment wheel raises and lowers with multiple full turns like most saws, but integrates a lock into the center. For the bevel adjustment, the outside of the height adjustment wheel turns a rack and pinion style system to accurately change the blade angle – a feature Makita shares.
There are a few nice conveniences which we don’t always see on affordable units like this. The Grizzly has a built-in miter guide, made from cast iron, which slides easily in the worktop. The left-tilting blade is coordinated with a digital display, which gives you an accurate, real-time readout on your bevel angle as you cut! The motor has a starting amperage of 13, which is safer for your breakers than 15 amp models. There’s a standard 4” dust collection port, and
Three professional carpenters test ten portable table saws, including two now discontinued. They outfit them all with Diablo 40-tooth general-purpose blades and test them on both 3/4-inch plywood and pressure-treated 2x pine. Each saw earns points for safety features, fence quality, stability, weight, stand design, ease of adjustment, cutting power, and dust collection. Totaling up these scores determines the saws' overall ranking, as well as their "class ranking" against comparably priced brands. Some additional single product reviews of table saws can be found elsewhere on the site as well.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
Clint DeBoer When he's not remodeling part of his house or playing with the latest power tool, Clint enjoys life as a husband, father and avid reader. He has a degree in recording engineering and has been involved in multimedia and/or online publishing in one form or another for the past 21 years. In 2008, Clint was one of the founders of the Pro Tool Reviews online magazine. He hopes his efforts at PTR will provide builders and contractors with reliable and engaging tool reviews to help them make better tool purchasing decisions.
Choosing the best portable jobsite table saw wasn’t an easy task but we’re confident we’ve done a thorough evaluation. In a very close race for the best table saw Hitachi beat out the DEWALT which came in second place followed by Skilsaw in third and Makita in fourth. It’s very interesting that the Hitachi and DEWALT look extremely similar. Hitachi edged out the DEWALT in performance and price resulting in the final scores. Skilsaw beat out Makita for the 3rd place only slightly and that result is really a function of pricing.

Our table saw review quickly showed that today’s portable table saws are light-years ahead of the small-saw offerings from a decade ago. They feature big-capacity cutting, greatly improved safety features and attached stands for easy setup. And saws in the upper price range rival stationary saws in accuracy and quality of cut. We limited our review to saws that included a stand with wheels and ones that could rip at least 24 in. wide, only the best table saw for our readers!
In terms of size, the table height from floor measures thirty four inches, with extension it measures twenty seven by forty inches and overall dimensions are 62 by 41 by 40 inches (LWH). This is simply an amazing saw and not only will you use it for many years to come, but it’s going to help you get the professional results you’re looking for in any project.
Three professional carpenters test ten portable table saws, including two now discontinued. They outfit them all with Diablo 40-tooth general-purpose blades and test them on both 3/4-inch plywood and pressure-treated 2x pine. Each saw earns points for safety features, fence quality, stability, weight, stand design, ease of adjustment, cutting power, and dust collection. Totaling up these scores determines the saws' overall ranking, as well as their "class ranking" against comparably priced brands. Some additional single product reviews of table saws can be found elsewhere on the site as well.

The dual extension tables (rear and side) offer 50% more table space than most rectangular units. We also appreciate that Grizzly have put all the space under the worktop to use, with steel-frame shelving built in as standard. You can use it for scrap wood, tools, and accessories: you can even fit a full tool chest under there! It’s a good space-saving touch for busy shops.


Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.
The Bosch will deliver a whopping big 25” rip, where the DEWALT maxes out at a 16” rip. Again, if you like the other features of the DEWALT better than the Bosch, this larger rip capacity might not sway your buying decision one way or the other. Personally, i would lean towards bosch, but that’s just me.It truly is the best portable table saw on the market today.
Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.

As far as the durability goes, it’s great. The materials used in the production of various components are sturdy and also quite reliable. The accuracy is at a high level meaning you won’t have issues with the precision of this table saw, even if you’re an absolute beginner. On the other hand, make sure you make the necessary adjustments when you unbox the tool, before turning it on. If you don’t know how refer to the user manual, it’s comprehensive and well-written.

The purchase of a table saw is no doubt a big investment. But there is a lot of flexibility in this class of tools to find one that fits in with your budget and your wants. Make sure to take into account how you will need to use the tool and where you will need to use it. Heavier models will be sturdier but they will also require more effort to load up when you need to.
The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.
Skilsaw SPT70WT-22 is a portable 10 in. Worm Drive table saw designed for ripping and is the first of its kind to hit the market. This Skilsaw has a powerful Dual-Field 15 amp motor that is powerful enough to handle even the toughest jobs. The motor has a smooth startup and runs cooler, so it lasts longer. With a small, compact size, easy to transport size, this portable saw has a lot to bring to the table. Skilsaw’s SPT99-12 is also this same table saw but also includes a rolling stand which allows you to easily transport and move this saw around the job site.

Hybrid models vary widely, so there aren’t any strict pros and cons that apply to all models. They’re generally quite powerful, and you can find them in both 110V and 220V configurations. They’re easy to install on wheeled bases, and work well in both stationary or mobile setups. However, these tend to be quite heavy, and they take up more space than other portable options. They’re a good compromise for ardent DIYers who dream of a cabinet model, but don’t quite have the money or the permanent shop space.
This woodworking website has tons of information about how to use a table saw: choosing blades, cutting joints, safety features, and more. However, we found only five actual product reviews, none more recent than 2013. Although these individual reviews are hands-on, they don't put saws through any specific, detailed tests. There's also no direct comparison between saws and no formal rating system.
About three paces from where I tested these portable table saws sits my late-model cabinet saw. As a serious woodworker and magazine editor, I can’t imagine not having it. Its powerful 3hp motor, spacious cast-iron tabletop and almost hair-splitting precision makes most other saw options pale by comparison. But all this said, a cabinet saw isn’t everything. The thought of moving that behemoth down the steps to a basement shop sends chills up my spine. I sure can’t toss it into a car trunk to help a friend down the road. My saw takes up a huge footprint of shop floor, and it cost a small fortune. I don’t know of any stationary table saw that sells for less than $700 new these days, and that can empty the coffer of a modest tool budget.
As mentioned, the look is similar to a hybrid with a full enclosure. Looks can be deceptive, though… The core design purpose is for this saw to stand up to constant heavy use in a commercial setting. This is not a tool you buy for casual woodworking at home.These bulky, heavy units are built to last the distance. They can weigh up to 500 pounds. You’ll get an accuracy and rigidity not available in lesser types of table saw.Other table saws call for regular adjustments. With a cabinet saw, you won’t need to do this as often once it’s set up properly. 240V motors developing 3-5HP mean there’s very little the best cabinet table saw won’t rip through with ease. Large sheets of hardwood are no problem at all.
There were really two major performance considerations we wanted to look at to help determine the best portable jobsite table saw: cutting power and dust collection. Power is an obvious choice. We want to make clean, straight cuts, but we don’t want to spend all day making them. Any saw can be calibrated to be straight and accurate, but some have to be babied more than others to get professional results.
These saws are the most difficult ones to categorize. The simplest explanation would be that they are somewhere in the middle between contractor and industrial cabinet saws. They are driven by an inboard belt motor. These units usually have open leg stands, but there are some models with closed ones – hence the whole confusion and difficulty in categorizing.
Today's table saws also include riving knives, which ride up and down with the blade when its height is changed, rather than splitters that are fixed in place. The problem with the old splitters was that they had to be removed for certain types of cuts, and users might forget to put them back on before making rip cuts. This increased the risk of kickback injuries, which occur when the spinning blade kicks back a piece of wood toward the user with tremendous force, causing serious injury to any part of the body that's hit.
This type requires a heavy-duty circuit because it’s driven by a powerful 3 to 5HP motor. The blade is driven by three parallel V-belts which ensure a smooth operation and an efficient transfer of energy. Needless to say, if you have big plans, you might want to consider investing in a high-quality cabinet saw. Prompted, it’s going to cost you a significant amount of money, but it pays out relatively quickly.
As we already said, people tend to remove the safety elements to speed up their projects. Needless to say, it’s a huge mistake. Those things are there for a reason, and they should remain installed at all times. As soon as you mingle with the parts, you’ll jeopardize the integrity and your own safety. Even the best table saw cannot protect you enough if you mess with the parts on your own.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.
One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
To learn about how table saws perform in real people's homes, we consulted owner-written reviews at retail sites like Amazon, Home Depot, Lowe's, and Sears. User reviewers don't have the breadth of experience that many experts enjoy, but they can provide keen insights on the model they bought, including things that might not crop up in the relatively short time professional reviewers have to spend with a given saw.

The Jet is a good midrange choice for people who like to keep things simple, and buy for the long term. The Jet has the longest warranty coverage of our three picks, and it comes with an excellent track record for reliability and durability. Many of its features are tweaked to be slightly more user-friendly that the Grizzly’s, and this unit is much easier to fit in a shop than the hulking Grizzly.


All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.

One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
Excellent saw. Got here sooner then expected. Fairly simple to put together. Folding stand is very solid and easy to operate. Takes up very little space in my garage. I've never owned a table saw before so I'm easily impressed. Some other buyers recommended upgrading the blade, which I did. The blade it came with was ok but the Freud 10 in. 40 tooth Premier Fusion makes a very smooth cut. I haven't hooked up dust collection to it yet but it seems like it would work great. The scale for the fence is spot on. I would highly recommend this to any diy.

DeWALT DWE7480 is an excellent table saw, especially if you consider its price. It’s a step up from the highly popular DW745 and slightly more expensive, but I think the larger rip capacity and higher RPM are well worth the extra money. The DWE7480 is still in the lower price region though, and unlike the DW745 you can also get this one with a stand: the DWE7480XA!
For this portion of the testing and evaluation we used three different materials (3/4″ AC Plywood, 5/4 Mahogany Decking, and 5/4 Pressure Treated Southern Yellow Pine Decking) while measuring the saw blade RPM, and the saw motor AMP draw. To compare the saws we’re looking for how much blade speed each saw has under load, and also how much the amp draw increases under load. Think about it like driving a car, a more powerful car will not drop as much speed going up a hill and the engine won’t work as hard.

We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.


We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
The Grizzly G0690 is a very unique and powerful table saw and each part of it says performance and quality. With a 3 HP, 220V, 3-phase Leeson motor, heavy cast iron trunnions, wings and table to its triple belt drive system, this model should definitely last you for a lifetime. It’s not only its impressive build quality that’s going to strike you about it, but also its other features that include a four inch dust collection port, a T-slot miter gauge, a magnetic switch, but also heavy cat hand-wheels, riving knife and camlock T-fence. If you’re a professional who’s been using cabinet tablet saws for a quite a while, you’ll immediately appreciate the quality of the Grizzly G0690.
How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.

Portable or “jobsite” table saws are the absolute opposite of cabinet models. These are the lightest, most travel-friendly table saws on the market. These are easy to pack up and store in the back of a pickup truck or work van, and they can be set up pretty much anywhere. You can fit them to folding stands, use them on countertops, or sawhorses. We love them for quick contractor jobs, and they’re the ideal tool for general handymen who do a lot of shorter jobs rather than extended carpentry fittings. These are also a great entry-level choice for DIYers who don’t need a massive table saw, but need something that they can pack away at the end of the day. And, of course, they’re the least expensive table saws you can buy!
It’s heavy-duty. Like all great cabinet saws, the Grizzly is built from parts that can last a lifetime or more. It has a cast-iron table, that’s precision-ground to be exactly level, with no warps or imperfections. The trunnion supports holding up the motor are also solid cast iron, which means that they don’t translate much vibration to the work surface at all. The paint on the cabinet and extension frames is powder-coated, and the miter gauge and riving knife are solid steel. Both extension table surfaces are made with a coated, engineered composite, which stands up well against dings or scuffs.
It’s powerful. The blade is hooked up to a 3HP motor which can muster a no-load speed up to 4000 RPM! That’s perfect for all your cutting needs, and it’s much better than other inexpensive units when it comes to slicing hardwoods or thicker stock. While many smaller units advertise similar HP ratings, this one actually lives up to the promise, since it uses 220V power.
The Bosch is, in fact, almost twice as heavy its competitor. Despite its aluminum try! But…..there may be other things to consider when you think about the portability of a worksite table saw. One consideration is the ease of setting up and moving the saw table. The Bosch, with its unique Gravity-Rise Stand and solid rubber wheels, may be heavier but easier to move and set up for use. The DEWALT wouldn’t require as much muscle to move, but the table is relatively small and it has no wheels. It bears mentioning that its table is sold separately, and is assembled separately, whereas the Bosch unit’s Gravity-Rise Stand is a part of the overall unit. The stand allows the saw to be raised into working position in a single, fluid movement, and easily cuts set up time in half.
We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.
PLEASE EXCUSE THE PICTURE, LUMBER JOCKS REQUIRED ONE. I AM AWAY FROM HOME AND COULDN’t RUN OUT TO THE GARAGE TO SNAP A SHOT. I am writing a review of my Bosch saw after a few months of use. I bought this saw last November after my Ryobi saw up and died during a project. I looked at several saws in the $600-$800 range and narrowed it down to four options. The Bosch and DeWalt jobsite saws, and the Delta and Ridgid contractor saws. My requirements were in a realativly compact saw th...
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
If you want to take the saw with you and use it in a different location, you can purchase the optional MB-PCS-000 integrated mobile base which features 2 stationary casters and 2 pivoting casters. Furthermore, it’s also possible to upgrade the mobile base assembly to a one thousand pound lift capacity, add a hydraulic piston lift and 4 independent pivoting casters.
As far as performance, the fence could be a bit better in its locking in – square front to rear – but you get used to being able to set it square and use the rear adjustment knob so that it stays put. Some folks have complained about motor burn outs – but having experience now with 17 saws – over 6 years or more – I haven’t encountered the problem (maybe we’ve been lucky?)
More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.
×