The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45 degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.
If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.
A magnetic switch is also good from a safety standpoint but may not be necessary on these smaller versions. A magnetic switch prevents the saw from starting back up if it loses power during a power outage. Basically, the power outage will turn off the saw. This is good because if for some reason the power were to come back on when you were not near the machine, the material could be shot out of it or damage the saw.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
How do you tell what the best table saw is? With so many table saw choices on the market it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.

First, consider the types of cuts you’ll need to make, and which types of stock you work with on a regular basis. Think about the largest rip cuts you need to make, and get a cabinet saw with a suitable max capacity for rips. Find the thickest stock you need to cut, and make sure your new machine has a high enough depth capacity to make the cut cleanly. The larger your average stock, the larger a workspace you’ll need on your new cabinet unit. It’s also a good idea to think about bevel and miter cuts which you’ll be making on your table saw. All of our recommendations have the capacity for both, but some come with miter gauges and others don’t.
RIDGID’s 94-lb. R4510 might not be a saw you want to lift into a truck bed every day, but it’s bound to deliver solid cutting results once you reach your destination. For starters, this saw includes a downright great stand. Step on one lever, and the tubular frame lifts and glides smoothly up into place. The same lever collapses it. It’s sturdy, well-balanced and provides a wide stance to keep the saw from shifting or tipping. Large wheels and rubber tires roll the machine around easily during transport or just to reposition it when set up. The left-most tube is both a working-height handle and side support for balancing extra-long crosscuts. Smart.

We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.

It’s the safest of the three by a long, long shot. SawStop became a major brand thanks to a feature that they’ve named their brand after: an accident-proof stopping mechanism for the traditional table saw. The innovative brake system on this model is the best on the market at detecting flesh and stopping the blade immediately. It’s a sure bet for saving fingers or worse injuries in the workshop.


The continuous-read, tape measure–type scale is ingenious and easy to read, and Ridgid’s lifetime warranty covers it against breakage. The Ridgid saw has the most versatile miter gauge with holes and slots for mounting extensions and accessories. The designers have cleverly fashioned the stand to also serve as a left-side outfeed support for ripping plywood.
Outfeed capacity is almost always the depth of the table. Pros using a jobsite table saw can opt to put a sawhorse or other support to hold the material after it passes the blade. There are a few models running around that give you some extra outfeed support, though. Most of the time, you’ll just have a buddy help guide the cut through from a safe stance on the behind the saw.

Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.

SawStop PCS31230-TGP252 10 in. 3HP table saw is a high performance cabinet table saw that features a durable cast iron table, 44 x 27 in. of total space, and is super durable, making it an ideal table saw for professionals. In addition to its industrial capabilities, this SawStop table saw also boasts a couple other practical features including a Flesh Sensing Technology, dissipative arbor belt to prevent hazardous charges, and an easy-to-change brake cartridge.
Give yourself a reason to smile every time you enter in your workshop by investing in this powerful instrument. DEWALT as a company guarantee quality in all their products for the interests of customer satisfaction. This Jobsite table saw is not exceptional. Its designed to provide precision and last longer. The saw features pinion and rack system that makes adjusting the fence easy and convenient. In other words, you will not strain or shift your concentration while on work. The table saw is designed with a rolling stand that guarantees you professional performance in all your cuts. It also features telescoping fence rails that retract and extend for a small portable package of the saw. Additionally, the table saw is suitable for both wide and narrow rip cutting as the fence can adjust based on the type of material you are cutting. Using a 15amp motor, you are sure that the saw will get the job done within minutes and save you energy cost.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.
When you’re deciding how much to spend, think about how often you use your saw, whether you’re using it as part of a professional workshop or as an avid hobbyist, and whether or not you can expect any return on your investments through your work. We recommend that DIYer spend closer to the $2000 mark, while professionals are more likely to get their money’s worth from something more premium.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.

Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.
As with our other models, it takes some assembly. If you get one of the extended models, which we’re recommending here, you should plan to cut the rails down to size before finishing installation. It’s simple to do if you’ve got a good miter or bandsaw, but it is an extra step. With that said, many reviewers complimented the SawStop’s well-written and helpful manual, which made installation significantly easier than other units.

As with the smaller Dewalt we’ve recommended, this one has very inconsistent quality control on the table. Some reviewers cited units with bowed, funky surfaces, while others got units that were perfectly flat. that’s a flaw of the molding process. We also have a bone to pick with Dewalt as far as the coating on these. While we understand that the coating is supposed to help wood slide better, it just doesn’t seem to last very long or hold up well. It also has the same flawed warranty coverage. We’d recommend purchasing add-on coverage.


The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.
If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.

Standard table saws are also called contractor table saws, even if they're really intended for the home do-it-yourselfer. These table saws have open, fixed legs, and they take up more space than a portable or benchtop table saw. They're also heavier – weighing as much as 200 to 300 pounds. On the plus side, their tables are often larger, making it easier to cut 4 by 8-foot panels of plywood or sheetrock. Prices for contractor saws range from around $600 to nearly $2,000.


It’s the safest of the three by a long, long shot. SawStop became a major brand thanks to a feature that they’ve named their brand after: an accident-proof stopping mechanism for the traditional table saw. The innovative brake system on this model is the best on the market at detecting flesh and stopping the blade immediately. It’s a sure bet for saving fingers or worse injuries in the workshop.

The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. There is tool-less assembly of the riving knife and anti-kickback pawls. It has a large easy to access ...  More + Product Details Close
Our table saw review quickly showed that today’s portable table saws are light-years ahead of the small-saw offerings from a decade ago. They feature big-capacity cutting, greatly improved safety features and attached stands for easy setup. And saws in the upper price range rival stationary saws in accuracy and quality of cut. We limited our review to saws that included a stand with wheels and ones that could rip at least 24 in. wide, only the best table saw for our readers!
A gauge will allow you to make very detailed cross and angled cuts. This is a bit of kit that you need to research in great depth as it can make or break the accuracy of your cuts and angles. With a good gauge, you can check blade height, blade angles, miter angles and much more. For further reading checkout Wikipedia’s table saw page and for in-depth air compressor reviews.
The Powermatic 1792001K PM2000 is an award winning cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. The 1792001K PM2000 is the result of years of work and research and hundreds of interviews with woodworkers that offered input which was eventually implemented in the saw. The performance, reliably and safety of this saw are so great, that they actually set a new standard by which all other cabinet saws are judged.
Contractor saws weigh quite a bit more than portable saws, averaging between 150 and 350 pounds, but are still somewhat portable. They have a heavier, cast-iron table top, and a motor that is usually more powerful than a jobsite saw. Even so, they’re within prices affordable for more committed hobbyists. Contractor saws can range between $800 and $2,000. They’re good for basic cutting tasks, as well as making home furniture and cabinetry work.
There are several types of table saws. The types of jobs or projects you plan to use a table saw for will determine which type you buy. If you want a saw you can take from job site to job site and store it easily, then you will need a table saw that is made to be portable so that it can be easily transported to the job site. Of the portable or work site table saws on the market today, the Bosch 4100-09 10-Inch Worksite Table Saw with Gravity-Rise Stand and the DEWALT DW745 10-Inch Compact Job-Site Table Saw with 16-Inch Max Rip Capacity are two of the most popular.

We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.
Perhaps you realized, that you need a cabinet table saw instead? For this i would highly recommend the SawStop PCS31230-TGP236 3-HP (Read Reviews) which is the top choice if you are a safety conscious woodworker. Some of you have also asked me about makita. Well, They do offer good products, but sell stands seperately, that is the reason they were not included in this guide….but i’ll try to make up for it in 2018.
The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.

Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
On the downside, these units are by far the heaviest type of saw, and they’re the most expensive by a long shot. Their cast iron worktops and steel cabinets makes them more of a permanent fixture than nearly any other tool. To move them around your shop, you’ll need an expensive, heavy-duty wheeled base, which can cost even more money up front. They’re best for people who will keep them in one place, and use them on a regular basis.
Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.
Sometimes picking a “Best Bet” is a real tossup, but not this time. While Bosch’s 4100-09 doesn’t disappoint, and DeWALT has what seems to be a bulletproof portable, I think RIDGID’s R4510 table saw really shines. Its sturdy workaday features, powerful motor and well-designed stand show that portability doesn’t have to mean compromise. This is an excellent woodworking choice for 10″ portable table saws.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
×