While ordering generic no-name products might be fine for something like breakfast cereal, power tools are different. When you use power tools, your safety is at stake. If you pick up some cheapo piece of mass produced junk just because the price is less than a name brand, you might end up paying a lot higher price for it than you counted on. Why? Because generic power tools are not usually held to the quality control and accuracy as big box brands such as DEWALT and Bosch.


With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.

I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!


Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
While DeWALT’s DW744X is the only model here without wheels, the saw is otherwise well appointed. It’s got a unique rip fence design: instead of sliding along front and back rails, the fence is fixed to them. To change rip fence settings, you extend the rails out on rack-and-pinion gears. The design keeps the fence parallel to the blade/miter slots and prevents it from deflecting if pushed laterally. A red hairline cursor makes fence settings easy to read, and it passed my ripping tests with flying colors.
I bought this saw to add to my home shop and a radial arm saw I have had for years. I have owned it since 2009. I bought it after reading reviews in woodworking magazines on line. I did buy the left extension, which I use frequently. This saw has been used for multiple projects, including building furniture, cabinets, cabinet doors and a host of other projects for home, family and friends. It has never let me down, working flawlessly. It has never been out of square. And, yes, I do check squareness every time I use it. Cuts are accurate and the table large enough to manage most jobs without adding an extension. The metal construction is particularly appreciated. The blade is easy to replace, the controls and storage on the unit convenient. What I particularly have enjoyed is the portability and the ease of use of the gravity-rise stand. Being able to move tools around and re-arrange my limited workspace to match the job is important to me. I have read the caveats posted by a number of reviewers, but, in truth, those have simply not been my experience. At 71 with a lifetime of using and buying tools and enjoy woodworking, I count this tool as among one of my better purchases.
But with top quality saws come features that some people may find well worth the extra investment, substantial though it may be, and thus our discussion starts with pricier models. At the top price range for table saws, you can often get a saw with safety technology that will automatically halt its blade the instant it encounters human flesh. (The process literally takes but a few milliseconds.) The knowledge that your fingers and hands are safe from major injury caused by a rapidly rotating, razor sharp blade is more than convincing enough for many people to invest in these technologically marvelous table saws.
I was hoping to see the JET in there. But glad you didn’t waste your time with it. I bought it a year and a half ago and it’s a piece of crap. It has not held up at all, I keep it in my construction trailer and it has its own cubby hole and is secured with straps. It has fallen apart. The fence has no adjustments and is off 1/4” front to back, From the factory. I have to spend so much time trying to adjust rip fence, and then I can’t turn my guys loose with it because they won’t take the time to adjust and check for accuracy. Just really disappointed in the product. I am waiting for the testing done on the cordless saws because I am upgrading.
If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.
But with top quality saws come features that some people may find well worth the extra investment, substantial though it may be, and thus our discussion starts with pricier models. At the top price range for table saws, you can often get a saw with safety technology that will automatically halt its blade the instant it encounters human flesh. (The process literally takes but a few milliseconds.) The knowledge that your fingers and hands are safe from major injury caused by a rapidly rotating, razor sharp blade is more than convincing enough for many people to invest in these technologically marvelous table saws.
As mentioned, the look is similar to a hybrid with a full enclosure. Looks can be deceptive, though… The core design purpose is for this saw to stand up to constant heavy use in a commercial setting. This is not a tool you buy for casual woodworking at home.These bulky, heavy units are built to last the distance. They can weigh up to 500 pounds. You’ll get an accuracy and rigidity not available in lesser types of table saw.Other table saws call for regular adjustments. With a cabinet saw, you won’t need to do this as often once it’s set up properly. 240V motors developing 3-5HP mean there’s very little the best cabinet table saw won’t rip through with ease. Large sheets of hardwood are no problem at all.
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
Obviously, given its size, the TruePower 01-0819 isn’t the kind of table saw you’d spring for to take on larger projects that require greater motor power — after all, it’s by no means revolutionary in the torque department. But for those who work with smaller materials or softer wood, the Gino Development TruePower 01-0819 Mini Electric Table Saw is a worthwhile, no-frills buy that’s easy on the wallet and can fit in virtually any space with plenty of room to spare.
so.categoriesWithItems ='8003,8002,8005,797,8007,696,8009,793,8011,8010,8013,750,8015,8014,833,823,825,8023,841,8017,2669,470,8041,430,8044,8047,263,8048,8050,306,8051,8053,5954,8055,8054,5957,8056,166,8059,39936,39934,39935,508,8025,5960,139891,139893,8030,566,8031,139905,8034,8033,8035,649,647,8038,661,491149,8742,505663,491151,505665,8277,143,8278,2234,8280,1224,2310,8285,8287,1222,116,6237,8292,8293,8294,8295,8296,8297,8298,8299,8300,8301,139847,139871,9022,39752,39751,39753,39754,997,8077,1022,1032,1025,8082,994,8084,139649,941,944,6471,910,8085,8087,1014,914,8090,8092,1258,8094,139687,8805,39895,39894,39896,39897,8063,224,8064,8065,5956,5959,429,39909,39908,39910,8130,5941,8131,902,1196,8137,8138,8141,8143,8142,8144,8145,1416,8148,8150,8151,1554,1422,8167,8163,8172,8174,8173,8182,8179,8183,39667,39665,469559,37938,469561,469563,37941,37940,37943,37942,37945,37944,37947,37946,3,8185,43,23,35,8191,8194,8195,1642,8196,8199,8200,139409,139411,452623,8203,8202,8204,8205,8206,8209,8210,139437,1299,1664,8216,8217,139455,139459,39703,39702,39704,108845,108843,8112,8111,8116,8114,8117,8115,8118,8106,8105,8107,8108,8109,8120,1132,8121,8122,8123,8126,6269,8221,681,8222,8220,8224,2584,8226,2575,678,662,2593,663,675,843,1699,8235,1805,8238,5980,8241,8244,8246,8247,5987,8248,8250,2614,6517,8253,8262,1307,139301,8264,187,8266,8265,8268,8267,8270,8269,8272,8271,8273,8274,39820,39819,108974,108972,468779,108975,139363,139359,139371,139369,930,928,2804,8101,919,8103,8102,39766,39765,139783,139767,108849,108848,108851,108850,140169,140167';
The Bosch weighs in at 52 lbs. While you could carry it one-handed, and it feels well-balanced, it would throw your personal balance way off and tire your arm. The DeWalt is a little lighter at 45 lbs., but it feels even lighter than that, and its weight distribution makes it feel less fatiguing to carry back and forth. (You can also carry the Dewalt saw one-handed by its handle or roll cage, but you probably won't want to.)
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
It’s the safest of the three by a long, long shot. SawStop became a major brand thanks to a feature that they’ve named their brand after: an accident-proof stopping mechanism for the traditional table saw. The innovative brake system on this model is the best on the market at detecting flesh and stopping the blade immediately. It’s a sure bet for saving fingers or worse injuries in the workshop.
One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
These smaller table saws, which come in a compact benchtop setup rather than with legs like a traditional table saw, are designed as portable job site saws. But they work just as well in a home workshop, and are ideal for shops that are tight on space. The Bosch and the DeWalt have many of their specs in common: Both include a 15 Amp motor, 10-inch blade, 3 1/8-inch depth of cut when the blade is set at 90 degrees and 2.2-inch depth of cut at 45 degrees. And safety features on both saws include a riving knife, anti-kickback pawls, blade guard and an included push stick. Features The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).
Some buyers weren’t impressed with the blade adjustments. The knobs and trunnions are similar to those on the DW745, but some reviewers said their units felt a bit clunky on the way down. Again, due to the quality control issues on these models, it’s a good idea to do a very thorough inspection and test of your unit before it’s too late to return it.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
If height adjustments were standardized, we could expect each saw to make them nearly identically. Taking a look under the hood, we discovered several different methods—each with their own effect. Most of the saws employ a bevel gear system that provides smooth and reliable performance. We noticed that many used solid metal gearing, but Bosch used plastic for both the 4100 and the REAXX.

Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.
If you want to have a quick and accurate cut of wood, look no further than a table saw. When buying a table saw the main thing you put into consideration is its power. A good table saw should have enough power to cut through wet timber as well as hardwood. However, there are certain features which help in foreseeing the overall performance of a table saw.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners. 
×