Before we get into some of the top features, we want to take a look at the design of this cabinet. As it uses an enclosed cabinet, you’ll find that the motor lasts longer because it doesn’t wear down due to constant exposure to dust. This cabinet also features convenient hand wheels on the front and sides that help you make quick adjustments before cutting or as you work.
This type requires a heavy-duty circuit because it’s driven by a powerful 3 to 5HP motor. The blade is driven by three parallel V-belts which ensure a smooth operation and an efficient transfer of energy. Needless to say, if you have big plans, you might want to consider investing in a high-quality cabinet saw. Prompted, it’s going to cost you a significant amount of money, but it pays out relatively quickly.

The continuous-read, tape measure–type scale is ingenious and easy to read, and Ridgid’s lifetime warranty covers it against breakage. The Ridgid saw has the most versatile miter gauge with holes and slots for mounting extensions and accessories. The designers have cleverly fashioned the stand to also serve as a left-side outfeed support for ripping plywood.
I definitely give this one 5 stars, but this is specific of the application – it being portable. If I was comparing it with other Hybrid saws, than this one doesn’t really compare when it comes to power. That being said. I was shopping for a table saw, after many years of working with a circular saw, and a straight edge – for me – it was time to get a setup for repetitive cuts that would be easier, and less time consuming (not to mention more precise, as the machine...
However, there were some limitations. The rip fence build, with a thin-metal body, is light-duty. At just 23⁄4″ wide, the saw’s narrow throatplate makes it harder to reach down inside for swapping blades or retrieving a fumbled arbor nut. While the white-on-black bevel scale display is easy to read, the thin red hairline pointer that marks tilt angles disappears over the top of it; the saw needs a larger, brighter indicator. There’s a geared mechanism for tilting the blade that engages when you push the blade height wheel in — a good thing — but the bevel lock lever is too short, and I would use care when bearing down on the plastic handle to tighten it.

Next, the rip fence is pretty hard to adjust also, and mine had a few thousandths of a bow, but that bow is way within industry standard for a portable saw. Here's what you do: First, check it for parallel, you might get lucky. (On a side note, there is a fine line between how tight to set the locking arm adjustment screw with this rip fence. Too tight, and when you lock it, you'll loose the self-adjustment feature, too loose isn't good either. Adjust the screw (on the rear of the fence), to where the fence self aligns while still getting tight) If you are like me, mine was 15 thousandths out, then unlock the locking handle and loosen the two screws on top closest to you in THIS ORDER! Loosen the screw closest to the lock handle first, and for a few turns. Next, loosen the screw that is about 6 inches away toward the middle just enough to where the fence will rotate on this screw, but not so much as to be sloppy. Begin experimenting. Pivot the fence back and forth, running your measuring device up and down the fence until you get pretty close. Lock handle and checking for parallel. Again and again. When you finally get pretty close to parallel, then lock the lever and experiment with locking both screws. If it doesn't move and you are within a few thousandths, then voila, you are done with adjusting the blade and rip fence for parallel. The other adjustments are straight forward, and once set up, THIS IS A GREAT SAW!!!!!!!!!!!!!! Good luck, hope this review helps
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
×