TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
The design is quite good. The SawStop safety system ensures smooth and flawless operation while protecting you from a variety of hazards. However, regardless of the safety aspects, you should always wear protective equipment, especially gloves and goggles. One of the most notable things about the design is the fact that it provides 99 percent dust collection both below and above the table. The riving knife maximizes kickback and also offers protection.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
Besides that, materials are expensive, and when you ruin even a couple of pricey work pieces with a saw that doesn’t provide accurate cut you will end up paying far more for that cheap saw than you anticipated. Having a good saw that you can depend on for accuracy and efficiency is a solid business move for any contractor. Both the DW745 and the Bosch 4100 have a true riving knife, anti-kickback pawls, and a blade guard to prevent kickback and possible injury.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.

However, it provides a bit less room to work, and it’s not as easy for newer woodworkers to use. The power/stop switch is rather small, and this one doesn’t have a digital angle display like the Grizzly. We highly recommend it to working professionals who need maximum cutting capacity in a minimal footprint. It’s also a good choice for ambitious DIYers who are short on space, but really know their way around a table saw.
These smaller table saws, which come in a compact benchtop setup rather than with legs like a traditional table saw, are designed as portable job site saws. But they work just as well in a home workshop, and are ideal for shops that are tight on space. The Bosch and the DeWalt have many of their specs in common: Both include a 15 Amp motor, 10-inch blade, 3 1/8-inch depth of cut when the blade is set at 90 degrees and 2.2-inch depth of cut at 45 degrees. And safety features on both saws include a riving knife, anti-kickback pawls, blade guard and an included push stick. Features The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).
We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.
The simplest way to find out what size your table saw needs or indeed if you’re buying a special size is to consult the table saw user Manuel. I would make sure you do this as often there are many things in modern tables saws that could affect the blade size and type. This is because modern saws have many different amazing and varied features, things size blade guards, special safety mechanisms and arbor sizes etc. With the We recommend you spend some time reading your manual in detail to avoid possible issues
For homeowners without the luxury of a huge garage to fit their enormous table saw, DEWALT’s DWE7480 is a compact alternative to bulkier machines with the same wood slicing power. Measuring 25.8" x 26.5" x 13.9", the DWE7480 hosts a 15-amp motor that cuts at an unbelievable 4800 rpm with a ten-inch blade, meaning this small package packs big performance — and with adjustable rear feet that are designed to allow users to level their table saw on uneven surfaces, you’ll be sure to get a clean, precise cut every time, no matter how rugged the terrain. An additional dust port makes collecting your sawdust a breeze — especially if you attach an optional shop vac extension.
The DEWALT Table Saw is designed with a The DEWALT Table Saw is designed with a 15 Amp 4800 RPM motor that quickly rips through hardwoods with ease. With 24-1/2 in. of rip capacity this saw easily cuts a variety of larger shelving and trim materials. Rack and pinion telescoping fence rails make fence adjustments fast smooth and ...  More + Product Details Close
Jeffery – As Rob explained things we had the RPM measurements running on that meter, and had to watch our video playback to evaluate the numbers (no recording of the numbers digitally). So we tried to take the average no load speed watching the video play back. Is it perfect? No….is a 10% difference a big deal? In this application I doubt it. If we were a full blown testing lab we’d have the data recorded digitally and take full blow averages, but alas we are not.

When you’re thinking about build quality, you should consider how often, and how intensively you’ll be using your portable table saw. The more you’ll use it, the more you should invest in a sturdy unit that’s built to handle all that use. If you’re only an occasional DIYer, on the other hand, you can probably stand to have a few more plastic parts on your unit, since you aren’t going to be putting it to the rest as often.
While DeWALT’s DW744X is the only model here without wheels, the saw is otherwise well appointed. It’s got a unique rip fence design: instead of sliding along front and back rails, the fence is fixed to them. To change rip fence settings, you extend the rails out on rack-and-pinion gears. The design keeps the fence parallel to the blade/miter slots and prevents it from deflecting if pushed laterally. A red hairline cursor makes fence settings easy to read, and it passed my ripping tests with flying colors.
Included Components (1) Gravity Rise Table Stand, (1) 10 In. 40-Tooth Carbide-Tipped Saw Blade, (1) Standard Throat Plate Table Insert, (1) Smart Guard System, (1) Rip Fence, (1) Miter Gauge, (1) Push Stick, (1) Blade Wrench, (1) Hex Adjustment Wrench (1) table saw, (1) 24-tooth carbide saw blade, (1) rip fence, (1) miter gauge, (1) push stick, (2) blade-change wrenches SPT70WT 10-Inch Portable Worm Drive Table Saw, Rip Fence, Table Insert, Barrier Guard Assembly, Anti-Kickback Device, Miter Gauge, Push Stick, 10-Inch Carbide 24-Tooth Rip Cutting Blade, Blade Wrench, Hex Wrench, Manual bare-tool Bare-Tool Bare-Tool
The service coverage under the warranty requires you to either bring the machine to an authorized dealer or ship it back to the company on your dollar. That’s a major downside, and it’s one reason we’re recommending purchasing add-on warranty coverage for this one. If you’re dealing with a third party provider, you can simply get a replacement without having to go through frustrating company reps.
These smaller table saws, which come in a compact benchtop setup rather than with legs like a traditional table saw, are designed as portable job site saws. But they work just as well in a home workshop, and are ideal for shops that are tight on space. The Bosch and the DeWalt have many of their specs in common: Both include a 15 Amp motor, 10-inch blade, 3 1/8-inch depth of cut when the blade is set at 90 degrees and 2.2-inch depth of cut at 45 degrees. And safety features on both saws include a riving knife, anti-kickback pawls, blade guard and an included push stick. Features The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).

We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.
When I switched blades, I did find the locking lever for the riving knife very stiff … not sure why. It raises to release the riving knife and pushes down to lock it. I resorted to gripping the lever with a pliers to manipulate it, after nicking some skin on the blade teeth. But, on the softer side, RIDGID provides a nice complement of overmolds on the miter gauge handle and blade height handwheel knob.
After cutting a bunch of wood with this saw, we really liked the balance of power and portability of Bosch GTS1031 – and I think that’s what this saw is all about. For raw Performance, the unflappable motor-blade combo earned a stiff 8/10 in our tests, while its affordable $399 price tag put it at a solid 9/10 in our Value scale. Sure, you can get cheaper portable table saws, but you’ll find it a challenge to track down the combination of power and portability the Bosch GTS1031 offers. Bosch’s gravity rise-equipped 4100-09 remains a compelling alternative or those wanting an integrated stand. It occupies an additional 15″ in width and 8″ in length and is a full 3.5″ taller. But it only tacks on 8 pounds in weight. If you’re cutting larger pieces of wood or need a saw with a stand, the 4100-09 may be your baby, but the new Bosch GTS1031, with its “toss it in the truck” form factor is our new sweetheart tool. While it has an available GTA500 folding table stand accessory, the real advantage of this saw is it’s stand-free portability – so don’t make it into something it’s not. After using this tool, we think you’ll want to take it with you, as-is, just about everywhere!
It has a smart fence design that allows for a wide rip capacity in a small package. The Dewalt’s rails telescope, which allows them to extend further than the competition without adding to the machine’s packable footprint. That means you can make rips at up to 20 inches without needing any extensions or other accessories. The rack and pinion system allows you to set a precise fence setting without wobble, even on a flexible rail. It locks at both the front and back, to make absolutely sure you’re getting an accurate rip every time.
DeWalt DWE7490X table saw is a pretty cool portable table saw. It’s a great blend of accuracy, portability, and power. Weighing only 58 lbs, this table saw might be pint size, but it’s not lacking power. It has an impressive 15 A motor, 28.5 in. rip capacity, 47 degree bevel capacity, and a cut depth of 3-1/8 in (at 90 degrees). Not bad for a portable table saw. Other features we appreciate are its tool free fence adjustments for convenience and its metal roll cage for extra durability. This package also includes a scissor style stand, which allows you to easily pack up this table saw and bring it with you anywhere the job takes you!
Even a newbie can go around the table saw section at the local home improvement store and feel that some saws have easier adjustments than others. Some are simply easier while others are downright innovative in various ways. Porter-Cable came out of the value group for the overall win with adjustments that are both smooth and intuitive. Dual adjustment wheels mean that you’ll be able to accurately adjust your blade height and your bevel angle—a feature no other saw in this group has.
Realizing that hanging on to a heavy, clumsy circular saw that makes inaccurate cuts is too primitive (and possibly dangerous) for your needs, you hit the Internet to find a table saw for your wood shop. With a stable platform and fixed-position blade, a table saw makes your rip cuts and cross cuts easier and more accurate. You no longer have to shy away from angled cuts, thanks to the miter gauge and bevel system specifically designed to take the guesswork out of miter and bevel cuts. Whether you need a portable table saw that fits in your garage or a full-size cabinet saw for professional woodworking, eBay is a great resource for new and used table saws. Featuring models like the compact Dewalt table saw and the Jet Heavy Duty Tilting Arbor table saw, the site sets you up with the perfect tools for your next home improvement project.
After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
Home Depot sells around 60 models of table saws on its website, and the top models get hundreds of reviews from users. We found four portable saws with ratings of 4.5 stars or better from 250 users or more, and one contractor saw gets ratings just shy of 4.5 stars overall from more than 650 owners. Individual reviews are fairly short and include ratings for quality and value.
×