You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.
Most table saw blades come in 8, 10 or 12inchs in diameter, but you can also get a lot smaller and larger sizes if you require special cut sizes and cut depth sizes. When looking for a new blade when it comes to sizes, blades are measured in two sizes mainly, the mounting hole and the total blade diameter, make sure you take the mounting hole size in to consideration when buying a new blade as this could be something very easily over looked but could cause an issue.

On the downside, these units are by far the heaviest type of saw, and they’re the most expensive by a long shot. Their cast iron worktops and steel cabinets makes them more of a permanent fixture than nearly any other tool. To move them around your shop, you’ll need an expensive, heavy-duty wheeled base, which can cost even more money up front. They’re best for people who will keep them in one place, and use them on a regular basis.
Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.

As for various accessories and attachments such as rip, miter and blade guard, these can be stored in their own specially designed hangars. If you plan on using other blades (and you probably will) there is also a well where you can store all the blades you have. In order to keep the surface of the table dust-free there is a dust collection port featuring a shrouded design which can be attached to the vacuum.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
This one’s compatible with Jet’s rolling bases. You can mount it on any of the company’s all-metal roller frames, and move it around your shop! That’s ideal for busy shops with a lot of large equipment and not a lot of space to spare. It’s also handy for home craftsmen who don’t have as much dedicated space as they’d like to devote to a table saw. The Grizzly, on the other hand, is much harder to convert to a wheeled base, because it has the dual extension tables.
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.
One of the things we looked at was the ease of assembly out of the box. We had the same person assemble each of the saws and timed the assembly to see if there are any significant differences between the models. The assembly time for the saws ranged from 21 minutes to 48 minutes. While some stands required more than twice the time, we felt the assembly time was not a significant enough factor to change someone’s mind on which saw to purchase.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
I build guitars in a small shop; I need my saw to be accurate, repairable and easy to store or move. I love this saw! I use it for everything from cutting down stock to slotting my fretboards. It gets out of the way, it came dead on square, and the dust collection works pretty well with a shop vac and great with a high volume dust collector, with an Incra miter fence it makes perfect, repeatable, and accurate cuts. After I had owned it for over a year the plastic lever on the riving knife broke - I called Bosch and they "goodwilled" me a new riving knife assembly (with an upgraded metal lever) via express mail. No charge and fast, friendly service - they didn't even ask for a serial number or proof of purchase. I'd buy this saw again in a minute - all tools wear out or break at some point and I really like that the company stood behind this one and got me up and running again in a hurry. I also love all the safety features - riving knife, anti-kickback pawls, large easy-to-reach power button, nice push stick, and a dust collection port that is positioned out of the user's way.
Cabinet saws are the prime choice for professional woodworkers. A more powerful induction motor, usually 3 to 5 HP, is enclosed in a cabinet, as part of a super-sturdy overall construction. This type of table saw is ideal for making smooth, straight cuts through hardwoods without worrying about excessive vibration. All that power and stability comes at a price, though. Low-end cabinet saws start around $2,300 and can go past $5,000 for industrial table saws.
The weak point of this rolling stand is the base where all the weight sits. I really like the Bosch rolling miter saw stand, which is what convinced me to buy this setup. When you compare the miter saw to this table saw, it's a night and day difference. The miter saw from Bosch has thicker and larger diameter metal tubing. It clearly weights more, but it's on wheels, and has yet to show any fatigue from constant use.
The best overall performance in our testing was the Skilsaw SPT99-12. The Skilsaw was described by many of the TBB crew as a beast and the data reinforces that. Regardless of the type of material the Skilsaw SPT99-12 offered the lowest drop in RPM’s and the lowest increase in AMP draw. Following in second place is the Hitachi C10RJ and the DEWALT DWE7491RS in third place.
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
×