The Grizzly G0690 is a very unique and powerful table saw and each part of it says performance and quality. With a 3 HP, 220V, 3-phase Leeson motor, heavy cast iron trunnions, wings and table to its triple belt drive system, this model should definitely last you for a lifetime. It’s not only its impressive build quality that’s going to strike you about it, but also its other features that include a four inch dust collection port, a T-slot miter gauge, a magnetic switch, but also heavy cat hand-wheels, riving knife and camlock T-fence. If you’re a professional who’s been using cabinet tablet saws for a quite a while, you’ll immediately appreciate the quality of the Grizzly G0690.
Safety is a prime concern for Bosch. From the SquareLock Rip Fence through to the patented SmartGuard System to lessen any chance of kickback, your security and comfort is taken care of. The blade guard and riving knife are quick-release. This takes away any excuse for not putting the guard back in place because it would be too much trouble, something that’s an accident waiting to happen.
The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
Included Components (1) Gravity Rise Table Stand, (1) 10 In. 40-Tooth Carbide-Tipped Saw Blade, (1) Standard Throat Plate Table Insert, (1) Smart Guard System, (1) Rip Fence, (1) Miter Gauge, (1) Push Stick, (1) Blade Wrench, (1) Hex Adjustment Wrench (1) table saw, (1) 24-tooth carbide saw blade, (1) rip fence, (1) miter gauge, (1) push stick, (2) blade-change wrenches SPT70WT 10-Inch Portable Worm Drive Table Saw, Rip Fence, Table Insert, Barrier Guard Assembly, Anti-Kickback Device, Miter Gauge, Push Stick, 10-Inch Carbide 24-Tooth Rip Cutting Blade, Blade Wrench, Hex Wrench, Manual bare-tool Bare-Tool Bare-Tool
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
Kenny Koehler An avid endurance athlete, Kenny has competed in triathlons (he's an Ironman) and various other fitness activities. Still, his passions lie with his faith, family, friends, and his love for well-designed power tools. With a background in science, you'll often find Kenny chatting up engineers at media events to get caught up on the latest tool technology.
After cutting a bunch of wood with this saw, we really liked the balance of power and portability of Bosch GTS1031 – and I think that’s what this saw is all about. For raw Performance, the unflappable motor-blade combo earned a stiff 8/10 in our tests, while its affordable $399 price tag put it at a solid 9/10 in our Value scale. Sure, you can get cheaper portable table saws, but you’ll find it a challenge to track down the combination of power and portability the Bosch GTS1031 offers. Bosch’s gravity rise-equipped 4100-09 remains a compelling alternative or those wanting an integrated stand. It occupies an additional 15″ in width and 8″ in length and is a full 3.5″ taller. But it only tacks on 8 pounds in weight. If you’re cutting larger pieces of wood or need a saw with a stand, the 4100-09 may be your baby, but the new Bosch GTS1031, with its “toss it in the truck” form factor is our new sweetheart tool. While it has an available GTA500 folding table stand accessory, the real advantage of this saw is it’s stand-free portability – so don’t make it into something it’s not. After using this tool, we think you’ll want to take it with you, as-is, just about everywhere!
It’s highly portable. The Dewalt is available with a folding stand, which makes it extremely easy to pack up. The guard assembly lies flat, and the fence can be retracted all the way to the table to keep everything neat and tidy. It’s pretty light, too-at just 45 pounds. We also love that the adjustment tools, accessories like the miter gauge, and even the guard components can be stored inside the saw for transport, or when they’re not being used.
There’s a lot to like about this saw. The stand is easy to set up and very sturdy. We like the smooth-operating table extension and the blade guard’s hold-up feature and ease of installation. The only downside we found is that the motor mount is less rigid than those on the other saws we tested. We suspect that’s why the cut quality on our torture test was not as good with this saw.
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
The price is okay. SawStop is a well-known manufacturer, and they have a pretty good quality control department. In simpler words, it may seem expensive to some, but it’s well-worth the money, especially if you’re a professional. A vast majority of DIY enthusiasts don’t want to make a huge investment in order to tackle a few minor projects; therefore, most of them tend to skip on buying a professional cabinet saw.
Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.
Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.
Let’s face it: guys get in each other's’ way at a job site. It’s not always easy to find room to work, so portability is a serious advantage when it comes to making the most out of your space. Luckily for the professionals out there — not to mention hobbyists who prefer to move around rather than work in the same spot everyday — RIDGID’s 15-amp table saw comes with a convenient mobile cart for stress-free transportation.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).
The table measures up at 29 inches by 21.5 inches. The 4100-09 is not suitable for dealing with large stock or sheets of wood. Made from aluminum, you’ll meet with no resistance as you slide the timber toward the blade. The only negative with the table is the way it’s finished with an anodized coating. This is fine to start with but tends to wear over time, something that doesn’t just look unsightly but can ultimately affect accuracy. This is a surprising oversight from Bosch and one we hope they rectify in future iterations of this fine table saw.
Make sure all the panels on the cabinet (including the motor shroud) are made from steel, and look for powder-coating on the panels to help the paintwork last. The adjustment flywheels, the fence rails, and the frame of the table assembly should be steel as well. The most important part to look at under the hood is the trunnion. The trunnion supports the motor, and you’ll want it to be made from solid cast iron. The sturdier the trunnion, the smoother your unit will cut.
One of the biggest perks of a cabinet table saw, aside from the rugged construction and wide worktop, is the sheer power of the tool. You should expect a cabinet table saw to cut absolutely any stock within its depth capacity smoothly and easily. Look for motors with at least 3 HP, and sophisticated belt drive systems which translate that grunt into 4000+ RPM blade speeds. Don’t accept lesser power ratings on a cabinet model: these are the gold standard of table saws for a reason!
Look for a blade guard and splitter assembly. The guard will keep your fingers and sleeves away from the blade, while the splitter will keep your wood from re-binding together and jamming the blade, or causing kickback. Kickback is one of the biggest hazards of using a table saw, aside from coming in contact with the blade. Make sure you have either a splitter assembly or a riving knife on any cabinet saw you use.
It is not a cabinet saw, so judging it by those standards would be unfair. As a portable job site saw this is amazing. Loud and dusty, sure, but that is expected. Easy to use and store, yes. The fence is square to the blade, and is rock solid, as long as you make sure the nut at the back of the fence is set right. The fence is not quite square to the table top, and I can't tweak it, but for construction I wouldn't care. I do other fussier things on the saw, so I will shim out an auxiliary fence. I made a cross-cut sled, which I recommend, and get thin kerf blades. I got a rip, general, and fine finish blades, and I get great results.
All table saws sold in the U.S. come with a riving knife, anti-kickback pawls, and a split blade guard. Because some cuts can’t be made with these safety features installed, they are removable. If you’re looking for a fun party game, see who of your uninitiated friends can install both correctly without a manual. While each one is different, their nature means you can use the saw without them installed. I’d be remiss if I didn’t tell you those cuts are more dangerous, so avoid it if you can.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
The blades are categorized according to number of teeth, diameter, arbor size, kerf size, application and speed. They can also be divided by material. Regular commercial table saws are 10-inch or 12-inch. Teeth usually number from 24-80. Many blades are tipped with diamond, carbon or carbide. This lets you cut through more than just wood. You will also need to think about the tilt of the blade. They are available in left tilt or right tilt. With a left-tilting hybrid or cabinet saw, the motor cover can get in the way of the sliding table. Router table extensions don’t work well on left-tilting saws.
Most table saw blades come in 8, 10 or 12inchs in diameter, but you can also get a lot smaller and larger sizes if you require special cut sizes and cut depth sizes. When looking for a new blade when it comes to sizes, blades are measured in two sizes mainly, the mounting hole and the total blade diameter, make sure you take the mounting hole size in to consideration when buying a new blade as this could be something very easily over looked but could cause an issue.
Clint DeBoer When he's not remodeling part of his house or playing with the latest power tool, Clint enjoys life as a husband, father and avid reader. He has a degree in recording engineering and has been involved in multimedia and/or online publishing in one form or another for the past 21 years. In 2008, Clint was one of the founders of the Pro Tool Reviews online magazine. He hopes his efforts at PTR will provide builders and contractors with reliable and engaging tool reviews to help them make better tool purchasing decisions.
This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.