Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.
The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!
The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.
Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.
The 708494K JPS-10TS from Jet Proshop is a high end cabinet table saw which delivers on all your expectations. Available in either a thirty inch or a fifty two inch rip capacity, this model is built from cast iron and is extremely rugged in order to withstand a lot of abuse and still deliver the excellent results you’re expecting from it. Regardless if you’re a professional or if this is the first cabinet table saw you’re planning to get, the 708494K JPS-10TS won’t disappoint. Its rugged build quality and ease of use are going to make it one of the best table saws currently available.

How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.
​If you decide to get a table saw with a one point five to two HP motor, then it’s going to operate at the standard household 120V circuit. When using a 2HP motor, you should expect it to draw between eighteen to twenty four amps. Also, keep in mind that in this case, the saw needs to be the only device that operates on a twenty amp circuit. The realistic limit of a one point five to 2 HP table saw is hardwood of up to two inches thick. If you need to cut thicker hardwood, then you’ll need a more powerful motor.

Finally, make sure you know your long-term options when it comes to maintenance, repairs, or replacements. Check the warranty coverage on your portable unit. Read the fine print, checking whether you’ll be paying for repairs under warranty, or whether the company will be footing the bill. Some manufacturers cover repairs, but not return shipping. Others force you to bring your unit to an authorized dealer, which can be difficult in some parts of the country.
The DEWALT DW745, due to its smaller size, does not have the capacity to use a stack of dado blades (blades designed to be stacked together to make wider cuts, grooves, and notches). It has also been noted that the plastic miter handle is a weak point, and it limits accuracy. There are no available table extensions. It does, however, come with a three year manufacturer’s warranty.
The larger the motor, the higher the voltage as well, usually 240V. In some cases, you may be lucky and have a garage or workshop that’s wired for 240V, so that is why it’s very important that you check this prior to getting the table saw. In terms of the material thickness it can handle, it’s a minimum of three inches. One thing to bear in mind is that safety is an essential consideration with these saws and that’s because the powerful motors are prone to higher kickback.
Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.
It’s highly portable. Even though the whole body feels sturdier than the Dewalt’s, it’s still relatively light, at just about 60 pounds. There are handles in both the top and bottom edges of the machine, for easy lifting, and once you’ve got the saw fixed to the base, you won’t have to lift it on your own except for when you’re loading it in the back of the truck/van.

As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
It’s expensive. This one will cost you over $3000. That’s no casual purchase, and the high price tag makes this cost-prohibitive for some buyers. However, you really can’t put a price on the peace of mind that comes with having a unit with this sort of safety system onboard. Our advice? If you can muster the cash, and will get your money’s worth out of the machine, it’s well-worth the price.
Service can be expensive on these models, so you should see if the company will be covering repairs, of if you’ll be expected to foot the bill. Add-on plans are a great way to minimize your liability if something goes wrong. By purchasing a third-party warranty, you can have a much better customer service experience. The warranty provider will deal with the company for you, so you don’t have to negotiate or deal with frustrating runarounds.

My intention with this website is to provide you with everything you need to know about table saws. I have tried to remain as objective and as informative as possible, and I hope you will be able to tell that when reading the reviews. Hopefully, you will find them helpful when it comes time to choose a table saw for your workshop or home. Good luck and take care.
The price is acceptable. One cannot say it’s a cheap piece of equipment because it’s not. But, the high quality of production and a great deal of precision justify the somewhat premium price. If you’re a devoted professional, the price shouldn’t be much of an issue for you. The only downside many people reported is the quality control within the company. Many models came with broken or missing parts.
More power is also associated with more control. More control also gives you the ability to cut tougher materials. Furthermore, more control allows you to use bigger blades with ease. For instance, a 1500W of the motor will result in swift movement of the blade as it spins. High RPM of the blade gives the user a greater chance of achieving accurate and precise cut. So, when shopping for a table saw, look out for a skill saw with the higher motor rating.

Ridgid seems to get mixed reviews from users, maybe due to its lower price point, but continues to impress us in head to head competitions. With this edition, Ridgid’s 15 amp motor powered through cuts better than any other saw we tested. Sure it was close, but it consistently beat out each competitor. That power does come with more vibration than some of the others though.
I really enjoyed your review and appreciate the significant time and effort put into it. How did you acquire the machines? Were they evaluation units provided by the manufacturers or did you buy them (randomly, like Consumer Reports)? If they were provided to you the cynic in me says you probably got cherry picked units. In looking at the various machines on line and checking out their comments, it’s quite clear pretty much all of them have a manufacturing distribution of performance and metrics e.g. for accuracy all the units you tested have comments ranging from great to truly awful. Same thing for build quality. I spent quite a while looking at the Dewalt but all the negative reviews on quality and accuracy turned me off it. I certainly do see many more positive reviews than negative reviews for the Dewalt, but it does leave you with the feeling that a dice roll is partly involved in buying a recommended table saw.
These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners. 
×