Being concentrated is extremely important. A big percentage of injuries happen due to the lack of focus at any given moment. Remember, if anything happens, it will happen in under a second. Naturally, you won’t have any time to react properly. Music is something that can be dangerous and relaxing at the same time. Some people love working while listening to their favorite tracks, but it significantly lowers your concentration level. Therefore, you should avoid listening to music while operating a heavy-duty piece of equipment.
However, there were some limitations. The rip fence build, with a thin-metal body, is light-duty. At just 23⁄4″ wide, the saw’s narrow throatplate makes it harder to reach down inside for swapping blades or retrieving a fumbled arbor nut. While the white-on-black bevel scale display is easy to read, the thin red hairline pointer that marks tilt angles disappears over the top of it; the saw needs a larger, brighter indicator. There’s a geared mechanism for tilting the blade that engages when you push the blade height wheel in — a good thing — but the bevel lock lever is too short, and I would use care when bearing down on the plastic handle to tighten it.
Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
Setting up both saws was quick and easy, since their factory-adjusted blades and fences were square and parallel to the tables' miter gauge slots out of the box (this is one of the reasons to buy a $350 table saw over a $100 one). Both saws had similar setup procedures: Attach the fence, raise the riving knife, attach anti-kickback pawls and attach the blade guard. There is no on-board stowage space for the DW745's rip fence, but this does not really affect the setup time or effort by much.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.

Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.
Service can be expensive on these models, so you should see if the company will be covering repairs, of if you’ll be expected to foot the bill. Add-on plans are a great way to minimize your liability if something goes wrong. By purchasing a third-party warranty, you can have a much better customer service experience. The warranty provider will deal with the company for you, so you don’t have to negotiate or deal with frustrating runarounds.

SawStop was second, also with features no other saw had. The blade height adjustment wheel covers the entire range with one full turn of the wheel. There was some discussion about micro adjustments being more precise for dado and rabbet cuts, but in practice, we found we could easily get to a specific height without trouble. SawStop also moves away from the bevel lock lever and instead integrates it into the height wheel. By pulling the lock toward you, it is released and easily moved to your desired angle. Let go of the wheel and it’s locked back in place without having to hold it and use a second hand to work the lever.


Different types of table saw rely on different motors. With the smaller and more portable saws, 120V direct drive motors can deliver up to 2HP. This is more than enough power if you’re working with less substantial sheets of material. The larger saws have belt drive motors running on 240V. These produce 3-5HP. Think carefully about the materials you’ll be working with. Get the right sized motor for your cutting needs.

While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.


Last but not least, you need to pay attention to the dust collecting capabilities of a particular model. Portable units usually have a weak dust-collecting capacity, but they aren’t foreseen for large projects. However, all other types do feature some kind of dust collecting system. The first thing you should check is the diameter of the dust port. The larger it is, the less debris you’ll have flying around. Also, check out the vacuum requirements because some models work only with super-expensive vacuums. As you can assume, the thing that’s lacking with those models is cost efficiency. However, if you don’t have budget limitations, feel free to invest in a high-end vacuum, it makes a huge difference.
The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
A table saw is the centerpiece of any home workshop, and it’s often the very first power tool to be cranked up at the start of any woodworking task. They’re essential for the necessary task of sizing wood for each project – whether narrowing the width of boards, cutting plywood sheets, or tackling specialized cuts like grooves, slots, and tenons. Because of their important role in DIY and professional construction, choosing the right table saw is critically important. At BestReviews, we’ve researched table saws in depth. We’re here to help you decide which type of table saw will best meet your needs.
The DEWALT and Makita finished in first for our ergonomic rankings followed by a tie for second between Hitachi and Skilsaw and a tie for third place by Bosch and Ridgid. Both the DEWALT and Makita built their saw with the professional contractor in mind. Overall the entire crew really likes the saws with a rack-and-pinion fence system and the large wheels on the Skilsaw were also a big favorite.
The Bosch 4100-10 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker. It includes Constant Response circuitry to help maintain speed under load, and overload protection.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.
In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
And finally, there are a couple of jobsite table saws running around with flesh detection to drop the blade out of the way if it detects a strike. There’s a significant premium in cost for these saws and there has also been plenty of litigation regarding whether it should be required on every table saw and whether more than one company has the right to manufacturer the mechanism. But they’ll save you a much worse injury in the event of an accident.

Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.


I’m not crazy about one feature, and it’s common to three of these five saws: to tip the blade, you unlock a lever behind the blade height hand wheel, then swing the undercarriage up to the angle you need before re-locking the lever. A geared bevel control would make this process a little easier. But, once tipped, Bosch held its angle setting well through my test cuts.

More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection. 
×