The frame is also improved. Instead of the basic roll-cage on the Dewalt, this one neatens things up with an integrated sub-base. It’s a rugged rubber-like pad which serves as a bumper between the main frame and your truck bed or worksite table. Both the table and the sub base are joined to the main frame, and they provide strength at both ends of the design. As with the Dewalt, you can store your tools and accessories inside, an on hooks outside the Bosch.
As far as performance, the fence could be a bit better in its locking in – square front to rear – but you get used to being able to set it square and use the rear adjustment knob so that it stays put. Some folks have complained about motor burn outs – but having experience now with 17 saws – over 6 years or more – I haven’t encountered the problem (maybe we’ve been lucky?)
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
Three professional carpenters test ten portable table saws, including two now discontinued. They outfit them all with Diablo 40-tooth general-purpose blades and test them on both 3/4-inch plywood and pressure-treated 2x pine. Each saw earns points for safety features, fence quality, stability, weight, stand design, ease of adjustment, cutting power, and dust collection. Totaling up these scores determines the saws' overall ranking, as well as their "class ranking" against comparably priced brands. Some additional single product reviews of table saws can be found elsewhere on the site as well.

Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
A splitter is a piece of metal that keeps the blade from binding in whatever material you are cutting if the saw kerf starts to close up. The splitter is vertical and sits directly behind the blade. This plays a big part in preventing kickback and should be mounted on the motor assembly so it rises and falls with the saw blades movements. You can also get splitters that can be adjusted to fit the width of the kerf.
The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a tool-less assembly of the riving knife and anti-kickback pawls. There is a large easy to ...  More + Product Details Close
Thanks for reading the fine print. About the Wiki: We don't accept sponsorships, free goods, samples, promotional products, or other benefits from any of the product brands featured on this page, except in cases where those brands are manufactured by the retailer to which we are linking. For our full ranking methodology, please read about us, linked below. The Wiki is a participant in associate programs from Amazon, Walmart, Ebay, Target, and others, and may earn advertising fees when you use our links to these websites. These fees will not increase your purchase price, which will be the same as any direct visitor to the merchant’s website. If you believe that your product should be included in this review, you may contact us, but we cannot guarantee a response, even if you send us flowers.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.

When you’re deciding how much to spend, think about how often you use your saw, whether you’re using it as part of a professional workshop or as an avid hobbyist, and whether or not you can expect any return on your investments through your work. We recommend that DIYer spend closer to the $2000 mark, while professionals are more likely to get their money’s worth from something more premium.


When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.
Cutting dadoes can be done with a dado stack blade. I use the Freud 208. Blade changes are easy, and there is a lever that locks the blade in place so I can get a good yank on the nut with the included (and stored onboard) wrench. There is an accessory throat insert for the dado blade stack, but the standard throat will easily handle a ¼ thick stack, which is what I usually use.
We’re not alone in loving the Jet’s guard system. We read lots of reviews from pros who said they’d used lots of table saws in their time, but this was the first time they didn’t absolutely hate the guard. In fact, many wrote that they started working with the guard onboard for the first time, simply because it worked so well. It’s certainly one of the most unobtrusive ones we’ve seen!
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
While we rotated the plate, we recorded the maximum reading on the dial indicator. We validated each maximum reading by running the test for a second time and noting that the readings were consistent. TBB also noted that as we performed these tests on all eight saws, the maximum readings occurred at different parts of the plate along its rotation. Because the max readings were in different and discrete parts of the calibration plate, TBB had a very high level of confidence in the flatness of the calibration plate, itself.
If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.

The Delta 36-L552 is the right cabinet table saw for boat building cabinet making and also woodworking. It features a fifty two inch Biesemeyere fence, speedometer style scales and also dual crank (up-front) controls with locking cams. Taking a closer look at the inside of the Delta 36-L552, we find a powerful 5 HP motor rated at 220V which is perfect for cutting engineered products such as melamine, MDF, but also hardwoods.
Another excellent choice for the hobbyist or at-home handyman, the SKIL 3410-02 10-Inch Table Saw is a great value, giving you a durable build and quality performance at a wallet-friendly price. It doesn’t have the same brand recognition as some of the more expensive options on this list, but reviewers love this machine and say that it’s perfect for woodworking and DIY projects.

One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
×