The type of woods you cut will determine how powerful a motor and how fast a blade speed you need from your portable table saw. If you’re going to be dealing primarily with thinner boards and softwoods, you don’t need anything hugely powerful. If you’re working with hardwoods or thicker softwood stock you should look for a more powerful motor. Likewise, if you’re only an occasional woodworker, you needn’t worry about finding a motor that won’t burn out.
Next, the rip fence is pretty hard to adjust also, and mine had a few thousandths of a bow, but that bow is way within industry standard for a portable saw. Here's what you do: First, check it for parallel, you might get lucky. (On a side note, there is a fine line between how tight to set the locking arm adjustment screw with this rip fence. Too tight, and when you lock it, you'll loose the self-adjustment feature, too loose isn't good either. Adjust the screw (on the rear of the fence), to where the fence self aligns while still getting tight) If you are like me, mine was 15 thousandths out, then unlock the locking handle and loosen the two screws on top closest to you in THIS ORDER! Loosen the screw closest to the lock handle first, and for a few turns. Next, loosen the screw that is about 6 inches away toward the middle just enough to where the fence will rotate on this screw, but not so much as to be sloppy. Begin experimenting. Pivot the fence back and forth, running your measuring device up and down the fence until you get pretty close. Lock handle and checking for parallel. Again and again. When you finally get pretty close to parallel, then lock the lever and experiment with locking both screws. If it doesn't move and you are within a few thousandths, then voila, you are done with adjusting the blade and rip fence for parallel. The other adjustments are straight forward, and once set up, THIS IS A GREAT SAW!!!!!!!!!!!!!! Good luck, hope this review helps
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.
A table saw is a powerful tool that makes short work of even large pieces of lumber, allowing you to make rip cuts down the grain of boards, beams, and even entire sheets of plywood. No carpentry shop or professional construction site is complete without a table saw. Deciding which saw is best suited to a given home workshop, furniture production factory, or building site is an important decision and merits careful consideration.

In my opinion, the Bosch is the clear winner here. While both of the saws are technically portable, the Bosch’s wheeled, easy to set up stand will get you to work quickly, without the need to keep track of multiple parts and accessories. While the DEWALT is much lighter, that difference is negated by the fact that you will be forced to carry it from the vehicle to where you will be using it, rather than pulling it behind you like wheeled luggage.
We had a number of these saws – and I bought one for my own use (travelling to my kids houses and for garage use) since my old Unisaw with sliding table isn’t exactly portable. My take on the blade – is that the old 40T one (Bosch CBT1040A) was not worth anything much – so the change to a 24T blade can’t hurt (zero time anything is still zero). They generally bundle saws with cheap blades to keep the overall price down – but when I was buying in many multiples – I would have been happy for $10 off each if I had a “no-blade” option.
In our introduction and how-to sections, we’ve talked about some of the key reasons to buy a cabinet-style model. These are the most stable table saws you can find. They produce the smoothest, cleanest cuts. They’re also tools that are built to last a lifetime. We recommend them to any professional with the shop space to install one. They’re also the ultimate choice to ardent hobbyists with plenty of room to spare and an ample budget.
Dust capture from this saw is pretty bad. I was shocked that a European brand would ignore the dust collection to this extent – at least I was until I discovered that their version of the 4100 does have quite a few more pieces that help pull most of the dust from the airstream. There is a plate that encloses the rear around the vacuum port and a bottom grid that allow airflow to the motor while still shaping the airstream to drive the dust to the vac. I added the plate, but decided against the grid. Instead, I added a sheet of ¼” plywood and put a 4” vacuum port in it that I hook up to my dust collector. I also replaced the blade guard with the European version that has a dust port built in. Minor upgrades, but dust capture has gone from terrible/non-existent to pretty acceptable. Bosch also sell a bag that will capture whatever dust would get tossed out the back of the saw, but that isn’t much, so I consider it a waste. I did buy it, and it works well on other tools, but it is not IMO a must-have for the 4100
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.
If you want to take the saw with you and use it in a different location, you can purchase the optional MB-PCS-000 integrated mobile base which features 2 stationary casters and 2 pivoting casters. Furthermore, it’s also possible to upgrade the mobile base assembly to a one thousand pound lift capacity, add a hydraulic piston lift and 4 independent pivoting casters.
If you’re a professional woodworker, you should expect a standard hookup on any saw. However, you’ll find that no portable table saw does a perfect job collecting sawdust. Since these aren’t enclosed tools like a cabinet saw, there are lots of ways for dust to find its way to your floor and spray around your shop. You’ll want to look for the most enclosed, effective design possible, and pair it with a vacuum system that’s got some heft.
I really enjoyed your review and appreciate the significant time and effort put into it. How did you acquire the machines? Were they evaluation units provided by the manufacturers or did you buy them (randomly, like Consumer Reports)? If they were provided to you the cynic in me says you probably got cherry picked units. In looking at the various machines on line and checking out their comments, it’s quite clear pretty much all of them have a manufacturing distribution of performance and metrics e.g. for accuracy all the units you tested have comments ranging from great to truly awful. Same thing for build quality. I spent quite a while looking at the Dewalt but all the negative reviews on quality and accuracy turned me off it. I certainly do see many more positive reviews than negative reviews for the Dewalt, but it does leave you with the feeling that a dice roll is partly involved in buying a recommended table saw.

Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.


As with our other models, it takes some assembly. If you get one of the extended models, which we’re recommending here, you should plan to cut the rails down to size before finishing installation. It’s simple to do if you’ve got a good miter or bandsaw, but it is an extra step. With that said, many reviewers complimented the SawStop’s well-written and helpful manual, which made installation significantly easier than other units.
Excellent saw. Got here sooner then expected. Fairly simple to put together. Folding stand is very solid and easy to operate. Takes up very little space in my garage. I've never owned a table saw before so I'm easily impressed. Some other buyers recommended upgrading the blade, which I did. The blade it came with was ok but the Freud 10 in. 40 tooth Premier Fusion makes a very smooth cut. I haven't hooked up dust collection to it yet but it seems like it would work great. The scale for the fence is spot on. I would highly recommend this to any diy.
Bosch 10” table saw has it all in terms of precision and accuracy. It has a riving knife system for high material controls and visibility in cutting. The blade is designed with anti-kickback pawls to ensure once you start cutting, you will get accurate results to the end. The entire unit is designed with heavy-duty material for durability. The square lock rip fence has adjustable style to guarantee continued accuracy and precision in all your work. Additionally, the table saw has an easy to transport design with additional tabletops handles for portability. You can also regulate the cutting speed of the table saw to the place you are comfortable.
The type of woods you cut will determine how powerful a motor and how fast a blade speed you need from your portable table saw. If you’re going to be dealing primarily with thinner boards and softwoods, you don’t need anything hugely powerful. If you’re working with hardwoods or thicker softwood stock you should look for a more powerful motor. Likewise, if you’re only an occasional woodworker, you needn’t worry about finding a motor that won’t burn out.

I do not which is the best table saw, but I can tell you which is the worst. The rigid portable saw is a piece of garbage. I have purchased two in the last 4 years and the motor has failed in both, only to find that they do not sell a replacement motor. The Rigid customer service will not respond to any questions associated with the saw or replacement parts. I will not buy another Rigid tool and currently planning to try the Bosch table saw.
If you need to move your saw around, it comes with a table saw stand that you can put up and down with ease. Fashioned from aluminum pipes with wheels that can handle uneven terrain, move around site without breaking your back. As well as its user-friendly nature, the stand can be stored away vertically so it’s a real space-saver whether at home or on the jobsite.

For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.

Buying a table saw can cover a lot of bases. You have everything from DIY models to professional production level cabinet table saws. In this article, we’re looking what is arguably the most popular – jobsite table saws. They’re on the less expensive side and are highly portable compared to their shop counterparts. That makes them go-to tools for framers, jobsite carpenters, and Prosumers.

SawStop PCS31230-TGP252 10 in. 3HP table saw is a high performance cabinet table saw that features a durable cast iron table, 44 x 27 in. of total space, and is super durable, making it an ideal table saw for professionals. In addition to its industrial capabilities, this SawStop table saw also boasts a couple other practical features including a Flesh Sensing Technology, dissipative arbor belt to prevent hazardous charges, and an easy-to-change brake cartridge.
Consider whether you’ll be working inside or outside, on even flooring or dirt ground. You’ll want to choose the most convenient stand that’s sturdy enough for the kind of cuts you need to make. Pros should pay for a premium stand that doesn’t have any wobble whatsoever. DIYers and framers can probably make do with something lightweight and inexpensive.
Portable or “jobsite” table saws are the absolute opposite of cabinet models. These are the lightest, most travel-friendly table saws on the market. These are easy to pack up and store in the back of a pickup truck or work van, and they can be set up pretty much anywhere. You can fit them to folding stands, use them on countertops, or sawhorses. We love them for quick contractor jobs, and they’re the ideal tool for general handymen who do a lot of shorter jobs rather than extended carpentry fittings. These are also a great entry-level choice for DIYers who don’t need a massive table saw, but need something that they can pack away at the end of the day. And, of course, they’re the least expensive table saws you can buy!
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.

And finally, they all include a blade guard that can be removed and reinstalled without tools. Because a few sawing operations, such as non-through cuts, require you to remove the blade guard, we like saws that make this task easy. The Bosch, DeWalt and Ridgid saws have well-designed blade guards that are easy to remove and reinstall. The blade guards on all but the Porter-Cable and Craftsman also have a feature that holds the blade guard in the raised position to allow better blade visibility for setting up cuts.
Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ...  More + Product Details Close
Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
×