The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.
post-template-default,single,single-post,postid-5859,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
Both of these table saws have a port that connects to a shop vacuum for dust collection. The DEWALT features a 2.5” port, while the Bosch has a 2” port. However, neither seems to do all that great a job. The Bosch might fare a little worse as far as the dust port clogging, but the DEWALT has some problems in this area, too. The Bosch is said to spew sawdust on the floor as though there was no dust collection port at all. The DEWALT racks up some complaints about the same problem.
If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
First off, consider how often you’ll put your table saw to use. If you work in the fields of contracting or carpentry, there’s a chance you’ll be using your new machine pretty often — so you may as well invest in a more expensive, heavy-duty table saw that’s sure to last longer than the average model. On the other hand, hobbyists and weekend woodworkers won’t need a pricey piece of machinery — a more compact and inexpensive model should do just fine, especially if you’re only working on smaller projects like birdhouses and DIY wooden models.
I recently brought the Ryobi RTS21G after my dwe745 got stolen and actually couldn’t believe the quality! You guys were definitely right about using the Diablo blade, makes a big difference as it’s not the most powerful table saw in the world, but really didn’t expect much for $200 but i was very surprised. Anyway just wanted to say thanks for the great review and recommendation!
One of the first and most important things to consider is what type of table saw you require. When considering the type make sure you consider things like, where will be using the saw, will it need to be portable and move from job to job or can it be stationary like in a work shop. Also, what will be the largest size bits of timber I will be cutting, what sort of power will I require and budget, below we’ve listed the main types so we hope it helps you find the right type for you.
Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.

As far as performance, the fence could be a bit better in its locking in – square front to rear – but you get used to being able to set it square and use the rear adjustment knob so that it stays put. Some folks have complained about motor burn outs – but having experience now with 17 saws – over 6 years or more – I haven’t encountered the problem (maybe we’ve been lucky?)
Buying a table saw is one of the biggest and most important purchases you will ever make when it comes to power tools. It is an integral part of most job site equipment, as well as an essential item for most do it yourself projects. Choosing a table saw that fits your particular needs and budget can mean the difference in both profitability and frustration level.
However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.
Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
Last but not least, you need to pay attention to the dust collecting capabilities of a particular model. Portable units usually have a weak dust-collecting capacity, but they aren’t foreseen for large projects. However, all other types do feature some kind of dust collecting system. The first thing you should check is the diameter of the dust port. The larger it is, the less debris you’ll have flying around. Also, check out the vacuum requirements because some models work only with super-expensive vacuums. As you can assume, the thing that’s lacking with those models is cost efficiency. However, if you don’t have budget limitations, feel free to invest in a high-end vacuum, it makes a huge difference.
In terms of size, the table height from floor measures thirty four inches, with extension it measures twenty seven by forty inches and overall dimensions are 62 by 41 by 40 inches (LWH). This is simply an amazing saw and not only will you use it for many years to come, but it’s going to help you get the professional results you’re looking for in any project.
All the articles on this website are short and punchy without much filler, but because there is so much to learn about table saws it will still take you the better part of an afternoon to read through them all. For those who don’t have that kind of time, or those who already know a great deal about table saws, this is the section that will take you to the best table saw for your needs.
If you’re going to have a quality product, you need a fence system that’s perfectly square to the table so your cut is perfectly parallel to the edge. Obviously, framers have a bit more leeway than jobsite carpenters and there’s plenty of variance in fence quality. Cheaper saws have fences that can easily move out of square as they slide along the surface of the table. Avoid these if you want quality results. The fence system needs to be easy to keep square to the blade.
Each one has different power, capabilities, mobility and price points as well. If you’re not sure which type you need, we have outline some specifics on each below that will help you choose. When you begin the search for your table saw, you will need to know the answers to a few questions that will narrow down the choices for you and make choosing much easier.
Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
It can seem like plastic is a weight-saver on the part of the manufacturer, but it’s really a cost-saver. You shouldn’t accept shoddy build quality in the name of getting a lighter machine. While no portable unit will include heavy cast iron components like a cabinet table saw, you can find metal alternatives that offer rugged, long-lasting build quality. Instead of plastic, look for aluminum.
The Grizzly, like the other cabinet models you’ll see here, requires a 220V power supply. If you’re a professional woodworker, you probably already have a 220V hookup. If you’re a home woodworker or DIYer, you’ll need to have one installed, if you haven’t already. It can be an expensive installation, so factor in the cost when you consider how much you’ll spend on your new saw.
We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.

For those of you who are looking to up your DIY game but don’t have enough capital to make the Dewalt DW745 happen for your home shop, this Craftsman is a decent budget choice. It’s powerful, lightweight, and extremely affordable. We don’t think you should expect too much from this one, though, since it has a very light table and a fence that won’t line up quite as precisely as you’d need for furniture-making or professional-grade projects. It’s cheaply-made, and doesn’t have as user-friendly a design as our other choices. For the home carpenter, though, this should do the trick for all your basic framing cuts.
DeWALT DWE7480 is an excellent table saw, especially if you consider its price. It’s a step up from the highly popular DW745 and slightly more expensive, but I think the larger rip capacity and higher RPM are well worth the extra money. The DWE7480 is still in the lower price region though, and unlike the DW745 you can also get this one with a stand: the DWE7480XA!
The quality of cut is as good as I can get with a cabinet saw, with one key exception: It takes more time to get it set up just right. There isn’t as much lead up before the blade, so getting the wood to track true is harder with less fence. I kind of wish they had backed the blade up an inch or two assuming they couldn’t make the saw a bit deeper.
Stands are one of those features where the ends really do justify the means. Some made us wish the manual writers would take a cue from Lego—just make the *@#$! things easy enough for a 7 year old to understand. That aside, SawStop set itself aside brilliantly, taking just 10 minutes to setup. All we had to do was install the wheels and two handles. Even the packaging is designed to make the process easier and the instructions were super-easy to understand. Makita was nearly as simple only requiring us to install the handle and bolt the saw to the stand.
The simplest way to find out what size your table saw needs or indeed if you’re buying a special size is to consult the table saw user Manuel. I would make sure you do this as often there are many things in modern tables saws that could affect the blade size and type. This is because modern saws have many different amazing and varied features, things size blade guards, special safety mechanisms and arbor sizes etc. With the We recommend you spend some time reading your manual in detail to avoid possible issues
If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.
Jeffery – As Rob explained things we had the RPM measurements running on that meter, and had to watch our video playback to evaluate the numbers (no recording of the numbers digitally). So we tried to take the average no load speed watching the video play back. Is it perfect? No….is a 10% difference a big deal? In this application I doubt it. If we were a full blown testing lab we’d have the data recorded digitally and take full blow averages, but alas we are not.

In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
Even a newbie can go around the table saw section at the local home improvement store and feel that some saws have easier adjustments than others. Some are simply easier while others are downright innovative in various ways. Porter-Cable came out of the value group for the overall win with adjustments that are both smooth and intuitive. Dual adjustment wheels mean that you’ll be able to accurately adjust your blade height and your bevel angle—a feature no other saw in this group has.
Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.
I build guitars in a small shop; I need my saw to be accurate, repairable and easy to store or move. I love this saw! I use it for everything from cutting down stock to slotting my fretboards. It gets out of the way, it came dead on square, and the dust collection works pretty well with a shop vac and great with a high volume dust collector, with an Incra miter fence it makes perfect, repeatable, and accurate cuts. After I had owned it for over a year the plastic lever on the riving knife broke - I called Bosch and they "goodwilled" me a new riving knife assembly (with an upgraded metal lever) via express mail. No charge and fast, friendly service - they didn't even ask for a serial number or proof of purchase. I'd buy this saw again in a minute - all tools wear out or break at some point and I really like that the company stood behind this one and got me up and running again in a hurry. I also love all the safety features - riving knife, anti-kickback pawls, large easy-to-reach power button, nice push stick, and a dust collection port that is positioned out of the user's way.
The saw itself is remarkably compact, measuring just 22.5″ square and a little over a foot in height (13″ to be more precise). With a steel “roll cage” that encloses the 4 HP 15-amp motor and a rubber handle that is positioned in the center of the right side of the saw, this is a tool that you’ll find very easy to toss into the back of a pickup or work van and take to any jobsite. When you carry it deck-inward, the weight of the saw presses in slightly against your leg – which actually steadies the saw somewhat, making it more manageable, though at 52-pounds let’s not go so far as to call this saw a breeze to carry. The Bosch GTS1031 included cord wrap, and the simple design of the frame also makes it easy to store up against a wall inside your shop when not in use. This isn’t a tool that really gets in the way much – it’s out of sight until it’s needed.

If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
The DEWALT DW745 and the Bosch 4100 are pretty evenly matched in having plenty of power and not-so-hot dust collection. I you’re looking for a light weight saw, the DEWALT comes in ahead since it weighs almost half as much as the Bosch. It is also the less expensive choice by far. The large work table, expanded cutting capability, and its Gravity Rise feature (with solid rubber wheels that make it easy to be rolling across rugged terrain at a jobsite) make the Bosch a Cadillac among Pintos, but, of course, that luxury comes with a price tag.
×