I never – not even with a big cabinet saw – enjoyed cutting down full sheets, and that isn’t going to change anytime soon. So, for me, the bigger capacity of the big saws isn’t as attractive as just cutting down the sheets with a track saw. Suddenly, with a track saw and a quality saw the size of the 4100, I can achieve the same results in a smaller footprint, for less money, more safely (I consider a track saw safer than manhandling full sheets alone)

Overall, I really like this saw. I have used it for trim work, and for cabinetry work. I worked for a guy who had the older model (the 4000) which is pretty much identical except that it does not have a riving knife (best safety upgrade ever) and it is still going strong after well over a decade of daily use. I wish there was more table in front of the blade, and I wish the dust capture was better, but it is a tremendously good saw and I consider it (with the addition of a track saw for full sheet handling) to be a viable alternative to a big cabinet saw.
Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.
After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
It’s highly portable. The Dewalt is available with a folding stand, which makes it extremely easy to pack up. The guard assembly lies flat, and the fence can be retracted all the way to the table to keep everything neat and tidy. It’s pretty light, too-at just 45 pounds. We also love that the adjustment tools, accessories like the miter gauge, and even the guard components can be stored inside the saw for transport, or when they’re not being used.
I’m no stranger to Bosch’s 4100-09 saw with Gravity-Rise™ stand. I’ve used one several times to build projects for this magazine, including the Serving Tray Cart that appeared in the June issue. So, I was not surprised when it tested impressively here. Rip cuts were on the mark, thanks to a rugged, beefy fence that stayed parallel to the blade each time I reset it. A flip of a red lever underneath unlocks the rails so they slide out and extend ripping capacity up to 25″.
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.
The riving knife and blade guard actually have a quick-release so you can easily remove it. This is important because, in the past, these elements were so hard to install once removed people would simply leave it off. Now that there is a quick-release feature it makes it much easier to put back on and avoid the involuntary donation if OSHA decides to visit the job-site.
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
As for various accessories and attachments such as rip, miter and blade guard, these can be stored in their own specially designed hangars. If you plan on using other blades (and you probably will) there is also a well where you can store all the blades you have. In order to keep the surface of the table dust-free there is a dust collection port featuring a shrouded design which can be attached to the vacuum.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.

The maximum depth of cut on a saw tells you how thick of a material you can cut through cleanly. Be careful when you’re looking at depth of cut ratings, since you’ll usually find two separate specs listed. One is for cutting at 90 degrees, the blade’s normal setting, and one is for cutting at a 45 degree bevel, which is generally the furthest a table saw blade will pivot. Most of us will only need to be concerned about the 90-degree rating, but if you cut lots of angles, you should check the 45 degree rating as well.
It’s compact. This one is just over two feet in either direction, and just under 14 inches high. It’s easy to fit in the back of a truck, or even on the passenger seat next to you on the way to your jobsite. It’s light, too. Buyers loved how easy this one was to carry around, especially home DIYers who had to set up and take down their units frequently.
If you’re a DIY enthusiast, you’ll definitely find something of interest. On the other hand, professionals can also find good pieces of information on this page. The models we’ve covered all work as advertised, and you can rest assured that they are of high quality. The only thing you need to do is determine how much money you want to spend and which type is the best suiting one for your requirements.
The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.

TBB used the same iGauging 35-125-4 digital dial indicator to measure the accuracy of the as-delivered factory fence to the table miter slot. We started by placing the fence in a locked position about 1” away from the blade on the opposite side from the miter slot. We adjusted the throw of the dial indicator so that we took the readings on the indicator, as before, in the middle of the indicator’s range of movement.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
As far as the durability goes, it’s great. The materials used in the production of various components are sturdy and also quite reliable. The accuracy is at a high level meaning you won’t have issues with the precision of this table saw, even if you’re an absolute beginner. On the other hand, make sure you make the necessary adjustments when you unbox the tool, before turning it on. If you don’t know how refer to the user manual, it’s comprehensive and well-written.
You’ll want to look for metal framing, and a design which allows for all the most delicate components to be stored inside the tool’s body. If you’re a DIYer who won’t be travelling with your saw often, you probably don’t need to worry about finding such a heavy-duty frame. Many portable units will fit easily on the passenger’s seat, so you won’t have to deal with wear and tear so much.
The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
×