At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.
One of the first and most important things to consider is what type of table saw you require. When considering the type make sure you consider things like, where will be using the saw, will it need to be portable and move from job to job or can it be stationary like in a work shop. Also, what will be the largest size bits of timber I will be cutting, what sort of power will I require and budget, below we’ve listed the main types so we hope it helps you find the right type for you.

It also has the highest blade speed. This model has a similar 15-amp motor to our other recommendations, but it’s geared for maximum efficiency. The result is a blade speed that’s nearly 1000 RPM better than the Bosch or the smaller Dewalt. Reviewers marveled at how powerful this one was compared to the size of the motor, which seems underwhelming from the outside. It rips right through oak, cherry, and other planks with no lag or burnout. In fact, we’re hard-pressed to find something this would struggle to cut, provided you equip it with the proper blade.
On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
Often called benchtop, jobsite, or worksite saws, portable table saws are typically made of lightweight materials, such as an aluminum table top, so that they’re easy to move from place to place. Sometimes they’ll have wheels attached to make shifting them around even easier. The motors on portable saws are also much smaller than on other types of table saws, and are typically less powerful.
The quiet, 220-volt motors in these saws cut through the hardest stock, hour after hour, without bogging down. Cabinets are metal and extend to the floor for the best dust collection. The tops are cast iron, wide, and stable, which makes it easy to cut sheet goods. The trunnions are cabinet-mounted, so you get minimal vibration and maximum accuracy. They're also heavy; some weigh over 600 pounds. Once a cabinet saw's in place, that's where it stays.

A dedicated writer and communications professional spending his days lost in the intricacies of both proposal and freelance writing. When not sharing the knowledge of both fully and self-insured medical benefits to employer groups of all industries within California, Jeff Newburgh can be found at home spending time with his family and 3 dogs, pondering the next chew toy to be thrown, while kicking back and relaxing with a nice glass of red wine.


The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.

The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
The Delta 36-L552 is the right cabinet table saw for boat building cabinet making and also woodworking. It features a fifty two inch Biesemeyere fence, speedometer style scales and also dual crank (up-front) controls with locking cams. Taking a closer look at the inside of the Delta 36-L552, we find a powerful 5 HP motor rated at 220V which is perfect for cutting engineered products such as melamine, MDF, but also hardwoods.
It has the widest rip capacity of the three. This one can handle materials up to 32 1/2”, which makes it ideal for folks who work with sheet stock on the go–especially when you consider the extra 22” you’ll have to the left of the blade. That’s thanks to the same rack and pinion fence as the smaller Dewalt. It’s even better on a larger scale, where the differences between this design and the sliding rail style you find on Bosch become very apparent. Reviewers agreed that this one felt much sturdier, smoother, and locked more securely than other portable units.

SawStop has an excellent stand and they’ve cleverly hidden the tool/miter/riving knife storage box under the side extension. Move the table extension and the box presents itself. Like DeWalt, two riving knives come with the saw—one with safety guards and one without. This keeps you from wondering how the pawls and guard go on the riving knife. Blade height fully adjusts with only one turn of the wheel. Not everyone was on board with this, citing less accuracy for dado and rabbet cuts. In the end, we showed we could be as accurate on the height as any of the other saws, so it’s a win.


Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.
This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.

The Porter-Cable looks like a beefed-up version of the Craftsman, with the same blade guard and anti-kickback pawls. This is the only saw in our test with a blade-tilting handwheel, which makes it easier to dial in a precise bevel angle. The motor mount and blade controls on this saw are very sturdy, without much play, which translates to a good-quality cut. Extending the fence for a wide rip requires a bit of effort on this saw, since the rails are stiff. All in all, this is a great saw for the price.
SawStop was second, also with features no other saw had. The blade height adjustment wheel covers the entire range with one full turn of the wheel. There was some discussion about micro adjustments being more precise for dado and rabbet cuts, but in practice, we found we could easily get to a specific height without trouble. SawStop also moves away from the bevel lock lever and instead integrates it into the height wheel. By pulling the lock toward you, it is released and easily moved to your desired angle. Let go of the wheel and it’s locked back in place without having to hold it and use a second hand to work the lever.

As with the smaller Dewalt we’ve recommended, this one has very inconsistent quality control on the table. Some reviewers cited units with bowed, funky surfaces, while others got units that were perfectly flat. that’s a flaw of the molding process. We also have a bone to pick with Dewalt as far as the coating on these. While we understand that the coating is supposed to help wood slide better, it just doesn’t seem to last very long or hold up well. It also has the same flawed warranty coverage. We’d recommend purchasing add-on coverage.
Make sure you know what’s covered and what’s not, especially if you’ll be using your machine commercially (many warranties are strictly for individual, not commercial use). It’s also a good choice in this case to purchase add-on warranty coverage from a third party at the checkout. We recommend these policies for most portable table saws, since most manufacturers have either very short warranty coverage, or longer warranties which require you to foot the bill for service calls or for returning the machine to the maker.

I was hoping to see the JET in there. But glad you didn’t waste your time with it. I bought it a year and a half ago and it’s a piece of crap. It has not held up at all, I keep it in my construction trailer and it has its own cubby hole and is secured with straps. It has fallen apart. The fence has no adjustments and is off 1/4” front to back, From the factory. I have to spend so much time trying to adjust rip fence, and then I can’t turn my guys loose with it because they won’t take the time to adjust and check for accuracy. Just really disappointed in the product. I am waiting for the testing done on the cordless saws because I am upgrading.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
These saws are the most difficult ones to categorize. The simplest explanation would be that they are somewhere in the middle between contractor and industrial cabinet saws. They are driven by an inboard belt motor. These units usually have open leg stands, but there are some models with closed ones – hence the whole confusion and difficulty in categorizing.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.
If you’re a professional woodworker, you should expect a standard hookup on any saw. However, you’ll find that no portable table saw does a perfect job collecting sawdust. Since these aren’t enclosed tools like a cabinet saw, there are lots of ways for dust to find its way to your floor and spray around your shop. You’ll want to look for the most enclosed, effective design possible, and pair it with a vacuum system that’s got some heft.
Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
I’m not crazy about one feature, and it’s common to three of these five saws: to tip the blade, you unlock a lever behind the blade height hand wheel, then swing the undercarriage up to the angle you need before re-locking the lever. A geared bevel control would make this process a little easier. But, once tipped, Bosch held its angle setting well through my test cuts.
If you’re looking to use a wheeled base, you’ll want a standard rectangular unit, not a cabinet with multi-directional extension tables. Double check to make sure the model is compatible with wheeled bases, and make sure you buy your base from the same manufacturer, so you have a guarantee that they’ll work together. No matter what, don’t skimp on your base! Remember that the frame and wheels have to hold up a machine that weighs 1/4 ton or more, so it needs to be incredibly sturdy.
Looking for a better way to take care of your wood cutting and still attain a professional result from the comfort of your home? Skil table saw with folding stand will provide exactly that. The foldable stand makes it convenient for any room use and storage. When the table saw is not in use, you can fold it right and use the space for other activities. It’s therefore suitable for small space users who are interested in professional cutting. Another interesting factor about Skil table saw, is that it cuts through materials that are 4 times the normal size. Therefore, instead of cutting each piece individually, you can set several materials to reach the height capacity for easy cutting. Additionally, the fence of this saw will guide and balance your material for accurate results. The saw also features huge blade to make the work easier and interesting for every user. If you invest in Skil saw, you will not only control your cutting but also upgrade your work to the level of expertise even if you are just starting off.
×