Next, the rip fence is pretty hard to adjust also, and mine had a few thousandths of a bow, but that bow is way within industry standard for a portable saw. Here's what you do: First, check it for parallel, you might get lucky. (On a side note, there is a fine line between how tight to set the locking arm adjustment screw with this rip fence. Too tight, and when you lock it, you'll loose the self-adjustment feature, too loose isn't good either. Adjust the screw (on the rear of the fence), to where the fence self aligns while still getting tight) If you are like me, mine was 15 thousandths out, then unlock the locking handle and loosen the two screws on top closest to you in THIS ORDER! Loosen the screw closest to the lock handle first, and for a few turns. Next, loosen the screw that is about 6 inches away toward the middle just enough to where the fence will rotate on this screw, but not so much as to be sloppy. Begin experimenting. Pivot the fence back and forth, running your measuring device up and down the fence until you get pretty close. Lock handle and checking for parallel. Again and again. When you finally get pretty close to parallel, then lock the lever and experiment with locking both screws. If it doesn't move and you are within a few thousandths, then voila, you are done with adjusting the blade and rip fence for parallel. The other adjustments are straight forward, and once set up, THIS IS A GREAT SAW!!!!!!!!!!!!!! Good luck, hope this review helps

With that said, the Dewalt DWE7491RS (another jobsite saw) has an amazing fence. It also has a greater ripping capacity – so if this additional functionality is more important to you than portability, it might be something to consider. Although keep in mind that it’s also 30lbs heavier, and the stand is much worse than that of the Bosch (which we’ll discuss later in this article).


The Delta 36-L552 is the right cabinet table saw for boat building cabinet making and also woodworking. It features a fifty two inch Biesemeyere fence, speedometer style scales and also dual crank (up-front) controls with locking cams. Taking a closer look at the inside of the Delta 36-L552, we find a powerful 5 HP motor rated at 220V which is perfect for cutting engineered products such as melamine, MDF, but also hardwoods.
About three paces from where I tested these portable table saws sits my late-model cabinet saw. As a serious woodworker and magazine editor, I can’t imagine not having it. Its powerful 3hp motor, spacious cast-iron tabletop and almost hair-splitting precision makes most other saw options pale by comparison. But all this said, a cabinet saw isn’t everything. The thought of moving that behemoth down the steps to a basement shop sends chills up my spine. I sure can’t toss it into a car trunk to help a friend down the road. My saw takes up a huge footprint of shop floor, and it cost a small fortune. I don’t know of any stationary table saw that sells for less than $700 new these days, and that can empty the coffer of a modest tool budget.
If you’re looking to use a wheeled base, you’ll want a standard rectangular unit, not a cabinet with multi-directional extension tables. Double check to make sure the model is compatible with wheeled bases, and make sure you buy your base from the same manufacturer, so you have a guarantee that they’ll work together. No matter what, don’t skimp on your base! Remember that the frame and wheels have to hold up a machine that weighs 1/4 ton or more, so it needs to be incredibly sturdy.

Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.


Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.
rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.
One of the first things many Pros do is permanently (and intentionally) lose the blade guard and anti-kickback pawls. While they are a pain to install and store onboard, their ability to reduce the risk of injury is significant. Table saws are responsible for thousands of injuries every year and there are plenty of guys running around with stories of how they got injured. So practice installing them until it feels natural and then actually use them onsite.
Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.

This Portable Table saw includes an industry standard This Portable Table saw includes an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a Tool-less assembly for the riving knife and anti-kickback pawls. It's perfect for mobile contractors and the Do-It-Yourself ...  More + Product Details Close
This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
Todd Fratzel   is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.

I build guitars in a small shop; I need my saw to be accurate, repairable and easy to store or move. I love this saw! I use it for everything from cutting down stock to slotting my fretboards. It gets out of the way, it came dead on square, and the dust collection works pretty well with a shop vac and great with a high volume dust collector, with an Incra miter fence it makes perfect, repeatable, and accurate cuts. After I had owned it for over a year the plastic lever on the riving knife broke - I called Bosch and they "goodwilled" me a new riving knife assembly (with an upgraded metal lever) via express mail. No charge and fast, friendly service - they didn't even ask for a serial number or proof of purchase. I'd buy this saw again in a minute - all tools wear out or break at some point and I really like that the company stood behind this one and got me up and running again in a hurry. I also love all the safety features - riving knife, anti-kickback pawls, large easy-to-reach power button, nice push stick, and a dust collection port that is positioned out of the user's way.
From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
×