One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.
One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.
After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.
In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
Balancing heavy-duty durability and lightweight design, this machine proves that good things can come in small packages. While buyers are overall happy with their purchases, they do seem to all agree on one thing: the DEWALT DWE7480 may be an overall investment, but it could seriously do with a miter gauge replacement. Buyers report replacing its inaccurate, plastic gauge for a solid, more detailed one.
One very popular alternative to the Dewalt is this Bosch unit. It’s a bit more rugged than the yellow saw, and it’s very well-regarded by working woodworkers. We particularly like the machined aluminum table, which is a big step up from the Dewalt’s molded surface. It also has the best rolling stand we’ve seen on the market to date, so it’s a superb choice for folks who work on a lot of jobs sites with mixed terrain.
Among the features that set this table saw apart from other competitors is the SquareLock Rip Fence. It is fabricated out of machined aluminum, slides up and down the rail without a hitch, and fixing positions couldn’t be easier. It’s probably the best fence I’ve seen in portable table saws, it feels very solid and is incredibly accurate and precise.
The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45 degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.
Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.