The DEWALT Table Saw is designed with a The DEWALT Table Saw is designed with a 15 Amp 4800 RPM motor that quickly rips through hardwoods with ease. With 24-1/2 in. of rip capacity this saw easily cuts a variety of larger shelving and trim materials. Rack and pinion telescoping fence rails make fence adjustments fast smooth and ...  More + Product Details Close

While we rotated the plate, we recorded the maximum reading on the dial indicator. We validated each maximum reading by running the test for a second time and noting that the readings were consistent. TBB also noted that as we performed these tests on all eight saws, the maximum readings occurred at different parts of the plate along its rotation. Because the max readings were in different and discrete parts of the calibration plate, TBB had a very high level of confidence in the flatness of the calibration plate, itself.

Make sure you know what’s covered and what’s not, especially if you’ll be using your machine commercially (many warranties are strictly for individual, not commercial use). It’s also a good choice in this case to purchase add-on warranty coverage from a third party at the checkout. We recommend these policies for most portable table saws, since most manufacturers have either very short warranty coverage, or longer warranties which require you to foot the bill for service calls or for returning the machine to the maker.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
Some table saws go one better than a splitter. Splitters are fixed. They do not move along with the blade. It also needs to be removed if you’re making cross-cuts or dado cuts. A riving knife, on the other hand, is fixed to the same part as the blade. This means it can move along with the blade. Riving knives don’t get in the way either so this is the best option.
The weak point of this rolling stand is the base where all the weight sits. I really like the Bosch rolling miter saw stand, which is what convinced me to buy this setup. When you compare the miter saw to this table saw, it's a night and day difference. The miter saw from Bosch has thicker and larger diameter metal tubing. It clearly weights more, but it's on wheels, and has yet to show any fatigue from constant use.
If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.
Included Components (1) Gravity Rise Table Stand, (1) 10 In. 40-Tooth Carbide-Tipped Saw Blade, (1) Standard Throat Plate Table Insert, (1) Smart Guard System, (1) Rip Fence, (1) Miter Gauge, (1) Push Stick, (1) Blade Wrench, (1) Hex Adjustment Wrench (1) table saw, (1) 24-tooth carbide saw blade, (1) rip fence, (1) miter gauge, (1) push stick, (2) blade-change wrenches SPT70WT 10-Inch Portable Worm Drive Table Saw, Rip Fence, Table Insert, Barrier Guard Assembly, Anti-Kickback Device, Miter Gauge, Push Stick, 10-Inch Carbide 24-Tooth Rip Cutting Blade, Blade Wrench, Hex Wrench, Manual bare-tool Bare-Tool Bare-Tool
Now let’s talk power. The 15-amp motor is housed underneath the aluminum table and features replaceable brushes so you can expect long life from the saw. The gearing for adjusting the blade height also looked to be built with durability in mind and was well-greased. Cranking the height on the saw was simple and, unlike many saws I’ve used, even bevel adjustments were a snap and didn’t require a ton of effort to move the blade. We found that we could easily loosen the bevel lock and slide the assembly along its arc until we got to the required angle.
One of the things we looked at was the ease of assembly out of the box. We had the same person assemble each of the saws and timed the assembly to see if there are any significant differences between the models. The assembly time for the saws ranged from 21 minutes to 48 minutes. While some stands required more than twice the time, we felt the assembly time was not a significant enough factor to change someone’s mind on which saw to purchase.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.

TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.

Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
A table saw can be classified in many ways, and I’ve come across terms like contractor, folding, featherboard, hobby, induction, sliding and zero clearance. However, I will conform to the most basic and clear classification and range the tables accordingly. That means I’ll order them by benchtop table saws, jobsite table saws, cabinet saws and hybrid table saws.
What 🤔?? I find it pretty rare to have to re-align the rack and pinion fence on the dewalt, but short of the first time figuring it out, it shouldn’t take more than 5-10 minutes to do. The time savings comes in not having to stick a tape to the fence every time you move it to ensure it’s parallel. I am excited to see other tool manufacturers are using rack and pinion fences now so that there are other options besides the dewalt, namely skil’s latest worm drive ts and the latest hitachi, I’m just not interested in any other fence system on a job site table saw.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
It’s highly portable. Even though the whole body feels sturdier than the Dewalt’s, it’s still relatively light, at just about 60 pounds. There are handles in both the top and bottom edges of the machine, for easy lifting, and once you’ve got the saw fixed to the base, you won’t have to lift it on your own except for when you’re loading it in the back of the truck/van.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
The purchase of a table saw is no doubt a big investment. But there is a lot of flexibility in this class of tools to find one that fits in with your budget and your wants. Make sure to take into account how you will need to use the tool and where you will need to use it. Heavier models will be sturdier but they will also require more effort to load up when you need to.
Table saws are versatile enough to earn a spot in every home shop—even if that shop shares the garage with the family car. The market offers a range of saws, from $200 portable, less accurate saws to heavy and very accurate cabinet saws costing thousands. All the table saws shown here have 10-inch blades that can cut though stock up to 3 inches thick, and they meet the Underwriters Laboratories' safety standards to prevent kickback. Keep reading for an extensive roundup of table saws, from portables to hybrid models.
If you work with wood in any capacity, chances are you rely on a table saw to make clean, accurate cuts. But when your good old saw goes to the big toolshed in the sky, it’s time to opt for a replacement. Before you dish out your hard-earned money on the first model you come across, remember that a table saw is a big investment, so it’s in your best interest to look into the many technical specifications of each option before you settle on a final purchase.
In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
Some table saws go one better than a splitter. Splitters are fixed. They do not move along with the blade. It also needs to be removed if you’re making cross-cuts or dado cuts. A riving knife, on the other hand, is fixed to the same part as the blade. This means it can move along with the blade. Riving knives don’t get in the way either so this is the best option.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.
DeWalt DWE7490X table saw is a pretty cool portable table saw. It’s a great blend of accuracy, portability, and power. Weighing only 58 lbs, this table saw might be pint size, but it’s not lacking power. It has an impressive 15 A motor, 28.5 in. rip capacity, 47 degree bevel capacity, and a cut depth of 3-1/8 in (at 90 degrees). Not bad for a portable table saw. Other features we appreciate are its tool free fence adjustments for convenience and its metal roll cage for extra durability. This package also includes a scissor style stand, which allows you to easily pack up this table saw and bring it with you anywhere the job takes you!
It’s easy to use, quite safe, and most importantly – it’s a high-quality piece of equipment for a more than reasonable price. If you don’t like what you see, don’t hesitate to read some of our other reviews, there might be something of interest for you. As far as this particular model goes, it should turn out to be a worthy and cost-efficient investment. In the end, it all comes down to your personal preferences.

The safety brake feature is a real step forward in engineering, but it does have a few downsides. The aluminum brake works with single-use cartridges, so you’ll have to replace the cartridge if you trip the sensor. Likewise, the impact of the brake, stopping the blade in milliseconds, will destroy your blade, so you’ll have to replace that as well. It’s a small price to pay for keeping your fingers or limbs, but it’s probably a good idea to stock up on cartridges and blades
We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
You have to know the amount of money you are willing to spend for the right saw. The truth is that the price will vary significantly depending on where you are buying the saw, the brand and the features it comes with. However, with a good budget, you can easily narrow down the options you may have. You will have a smaller range to work with and you will know what features to expect within that price range. Always be willing to spend a little more on the table saw you want in your workshop especially if you work on wood every day.
As far as the durability goes, it’s great. The materials used in the production of various components are sturdy and also quite reliable. The accuracy is at a high level meaning you won’t have issues with the precision of this table saw, even if you’re an absolute beginner. On the other hand, make sure you make the necessary adjustments when you unbox the tool, before turning it on. If you don’t know how refer to the user manual, it’s comprehensive and well-written.
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.

TBB used the same iGauging 35-125-4 digital dial indicator to measure the accuracy of the as-delivered factory fence to the table miter slot. We started by placing the fence in a locked position about 1” away from the blade on the opposite side from the miter slot. We adjusted the throw of the dial indicator so that we took the readings on the indicator, as before, in the middle of the indicator’s range of movement.
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
Most shippers will expect you to have a forklift to get the crate off the truck, so if that’s not something you can arrange, you’ll want to opt for “lift-gate” delivery or an installation plan that involves the shippers bringing the saw to your actual workshop. Be prepared to spend a fair bit of money for delivery ($100-$250), especially if you can’t get the saw off the truck and to the workshop on your own.
The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).

More power is also associated with more control. More control also gives you the ability to cut tougher materials. Furthermore, more control allows you to use bigger blades with ease. For instance, a 1500W of the motor will result in swift movement of the blade as it spins. High RPM of the blade gives the user a greater chance of achieving accurate and precise cut. So, when shopping for a table saw, look out for a skill saw with the higher motor rating.
×