You can’t talk about the best portable jobsite table saw without talking about portability. Portability boils down to a couple of important features. First and foremost, weight has a huge impact on how easily you can transport the saw, especially if it has to go into the bed of a truck rather than a trailer. If you’ve got a trailer, then a wheeled stand becomes your best friend. We looked at both.
Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
You can store and transport the Bosch upright or on either of its sides. In between our tests, we found that the saw neatly stored away on its side on a workbench shelf. On the other hand, the DeWalt can only be stored or transported in its upright position. While it may possible to rest the saw briefly on one of its sides, there is the potential to damage the power cord, plug, or the ends of the telescoping fence rails. 

The only dislike that I have found about the Bosch 4100-09’s operation is that unlocking the table causes a tab to pop up above the cutting surface. This tab interferes with the operation of the fence, and could lead to damage of the product. It also comes with only a one year warranty. It does have available rear out-feed extensions available, to help facilitate larger work pieces.

Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today. 
The Porter-Cable looks like a beefed-up version of the Craftsman, with the same blade guard and anti-kickback pawls. This is the only saw in our test with a blade-tilting handwheel, which makes it easier to dial in a precise bevel angle. The motor mount and blade controls on this saw are very sturdy, without much play, which translates to a good-quality cut. Extending the fence for a wide rip requires a bit of effort on this saw, since the rails are stiff. All in all, this is a great saw for the price.
I really do like your site and being on Long Island there is a familiarity to the way y’all work. You are quick to respond to comments and put in a great effort but…. This review I feel you miss the mark. Out of box accuracy is important but. Ore important to a pro user is tool able to be adjusted to be near perfect and how does it hold this position. No comments on how solid the fences are, ie deflection movement, ease of micro adjust, etc. all the fancy self feed stuff etc, what saw feels the most powerful? Smoothest ? All theses kizmos are for the manufacturers to hype. Your strengths are that you actually use these machines, so your strengths are to BE MORE opinionated or biased not less because your opinion has meaning or weight. Let the know knowings use the kizmos and just give us your real opinions based on real use. Just my 2 cents.
We spent 42 hours on research, videography, and editing, to review the top options for this wiki. Regardless of whether you're a construction professional, a precision woodworker, or a DIY hobbyist tackling your next home-based shelving project, one of these handy table saws will help you get the job done fast. Our selections include models with durable cabinets, powerful motors, integrated fence rails, and even patented safety systems to protect you from on-the-job injuries. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best table saw on Amazon.

I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!


In recent years, there has been a cloud of controversy surrounding the inherent safety issues surrounding the table saw. SawStop developed a flesh detection technology that pulls the blade below the table surface 3 milliseconds after coming into contact with skin. It really created a new class of table saw that, as of June 1st, finally has some competition in the form of Bosch’s REAXX.
Jet has a strong reputation for providing customers with durable power tools that operate just like professional models but cost less, and that is definitely true of this 10-inch table saw that comes with a riving knife. You’ll like the basic design of this model, which has an intuitive design that allows you to set it up and start cutting faster. It features both a solid cabinet as well as an extension table that stretches out from one end.
The Bosch is, in fact, almost twice as heavy its competitor. Despite its aluminum try! But…..there may be other things to consider when you think about the portability of a worksite table saw. One consideration is the ease of setting up and moving the saw table. The Bosch, with its unique Gravity-Rise Stand and solid rubber wheels, may be heavier but easier to move and set up for use. The DEWALT wouldn’t require as much muscle to move, but the table is relatively small and it has no wheels. It bears mentioning that its table is sold separately, and is assembled separately, whereas the Bosch unit’s Gravity-Rise Stand is a part of the overall unit. The stand allows the saw to be raised into working position in a single, fluid movement, and easily cuts set up time in half.
The Grizzly, like the other cabinet models you’ll see here, requires a 220V power supply. If you’re a professional woodworker, you probably already have a 220V hookup. If you’re a home woodworker or DIYer, you’ll need to have one installed, if you haven’t already. It can be an expensive installation, so factor in the cost when you consider how much you’ll spend on your new saw.
The RK7241S has two sturdy tubular legsets that fold down and lock, and one becomes a convenient handle for transport. The stand stayed put during heavy ripping operations, and lawnmowerstyle wheels make the tool easy to roll. But, once set up, you have to drag or lift the saw to move it, unlike other portables that keep the wheels on the floor during use.
Compared to some of the other miter saws we’ve used – predating the new riving knife requirement, the Bosch GTS1031 guard system is much easier to install and remove when necessary (and to put the saw back into portable mode). We timed ourselves and assembled and tore down the saw in just over 2 minutes – and we were confident that our time would get better with more practice. The table is made of machined cast aluminum and is texture-coated to make it fairly slick – something that really helped when cutting larger pieces of 3/4″ plywood for a workbench surface. As for extending the table – that was super-easy. You just lift the table extension handle upwards and slide the table to the right. This gives you a full 18″ of rip width to the rip fence with your material to the right of the blade. Collapsed, you get up to 10″. Motion of the rip fence and the table extension were smooth. While the fence had some wobble in it at the far end – this completely disappeared when you locked it down – and the shape of the rear of the fence locked it straight every time. It’s a good system and more than adequate for a low-cost portable saw like this. We’ve seen more robust fence systems. But typically the trade-off has been in weight as well as cost.
Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.

Included Components (1) Gravity Rise Table Stand, (1) 10 In. 40-Tooth Carbide-Tipped Saw Blade, (1) Standard Throat Plate Table Insert, (1) Smart Guard System, (1) Rip Fence, (1) Miter Gauge, (1) Push Stick, (1) Blade Wrench, (1) Hex Adjustment Wrench (1) table saw, (1) 24-tooth carbide saw blade, (1) rip fence, (1) miter gauge, (1) push stick, (2) blade-change wrenches SPT70WT 10-Inch Portable Worm Drive Table Saw, Rip Fence, Table Insert, Barrier Guard Assembly, Anti-Kickback Device, Miter Gauge, Push Stick, 10-Inch Carbide 24-Tooth Rip Cutting Blade, Blade Wrench, Hex Wrench, Manual bare-tool Bare-Tool Bare-Tool
​The saw does not easily detach from the stand. Sometimes it’s beneficial to set the saw up as a bench-top saw, but the DeWALT 7491RS doesn’t come with quick release levers to accomplish this easily. In this case, you would have to use a drill to remove four screws to detach it from the stand. I wouldn’t recommend doing this unless you have to because over time the screw holes will strip.
Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
Being concentrated is extremely important. A big percentage of injuries happen due to the lack of focus at any given moment. Remember, if anything happens, it will happen in under a second. Naturally, you won’t have any time to react properly. Music is something that can be dangerous and relaxing at the same time. Some people love working while listening to their favorite tracks, but it significantly lowers your concentration level. Therefore, you should avoid listening to music while operating a heavy-duty piece of equipment.
In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
PLEASE EXCUSE THE PICTURE, LUMBER JOCKS REQUIRED ONE. I AM AWAY FROM HOME AND COULDN’t RUN OUT TO THE GARAGE TO SNAP A SHOT. I am writing a review of my Bosch saw after a few months of use. I bought this saw last November after my Ryobi saw up and died during a project. I looked at several saws in the $600-$800 range and narrowed it down to four options. The Bosch and DeWalt jobsite saws, and the Delta and Ridgid contractor saws. My requirements were in a realativly compact saw th...
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
×