The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
Plus, the machined aluminum table is our favorite on the market right now. It also has a smarter motor system than either of the Dewalt’s, thanks to a soft start and automatic speed control to ensure smooth cuts. However, it’s the slowest of the pack, and it doesn’t have quite as good a fence as the yellow competition. We think it’s a great choice for pros who are concerned about accuracy, but can’t spend lots of money on their unit.
It’s the best of the three at keeping your shop clean. The SawStop has a blade guard and arbor enclosure that’s engineered and sculpted to maximize vacuum suction at the cutting edge. Plus, the guard hugs tightly to the blade, and like the Jet, opens at each side so that whichever way you’re cutting, dust goes down the vacuum chute instead of off to the side of your workspace. It’s lab-tested to be up to 99% effective, and it’s certainly the most impressive dust collection system we’ve seen to date.
You’ll want to look for metal framing, and a design which allows for all the most delicate components to be stored inside the tool’s body. If you’re a DIYer who won’t be travelling with your saw often, you probably don’t need to worry about finding such a heavy-duty frame. Many portable units will fit easily on the passenger’s seat, so you won’t have to deal with wear and tear so much.
The 15-amp motor is outstanding, developing up to 4HP and operating at a speed of 3650RPM. This is not quite as pacey as the DeWalt but still more than respectable. The other advantage to this motor is that – for a table saw, at least – it’s pretty quiet. Noise isn’t such an issue out on the job site but if you’re woodworking at home, the quiet motor is a real boon.
Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
It has a smart fence design that allows for a wide rip capacity in a small package. The Dewalt’s rails telescope, which allows them to extend further than the competition without adding to the machine’s packable footprint. That means you can make rips at up to 20 inches without needing any extensions or other accessories. The rack and pinion system allows you to set a precise fence setting without wobble, even on a flexible rail. It locks at both the front and back, to make absolutely sure you’re getting an accurate rip every time.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.
The Powermatic used to be another all-American classic, much like the Delta. This latest version has the same recognizable yellow finish, on a steel cabinet and cast iron worktop. Unlike most other cabinet units, this one has cast-iron extension wings, which makes them just as sturdy and level as the central worktop. It’s loaded with a 3 HP motor, a 50-inch fence, and all the other basic features that our top three picks have.
How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
The bench table saw is the least expensive of the four types of saws. Some models come with a folding stand that is on wheels which makes it very easy to move or reposition without having to lift it all the time. Even though it is relatively light, constant lifting can become tiresome. You can mount these on your workbench which will give it more stability and could possibly reduce the amount of vibration as well. These smaller table saws generally have a 1 hp motor or even smaller and can run on a normal household circuit with no issues.
We’re impressed with how much thought SawStop have put into all the features on this model. It has an extra-large bevel gauge ruler on the side of the cabinet, tool-free, modular guard system, and compatibility with innovative wheelbases which don’t add noticeably to the SawStop’s height or footprint. It also has beveled edges to protect your materials, a very nice touch that our other recommendations don’t have. All in all, it feels like a tool designed by people who use one of these units on a regular basis.
To test the saws' cutting prowess, we made a series of cuts on both the Bosch and the DeWalt with woods that homeowners and DIYers might use on a compact table saw. To be specific, we ripped 24" x 24" sheets of 3/4" and x1/4" plywood into strips, and made 45-degree bevel cuts in 13/16"-thick cherry, cross-cuts in 10"-wide, 3/4"-thick shelving, test cuts in 2x4 stock, rip cuts in 3/4" red oak and 30-degree cross-cuts in poplar.
Sometimes picking a “Best Bet” is a real tossup, but not this time. While Bosch’s 4100-09 doesn’t disappoint, and DeWALT has what seems to be a bulletproof portable, I think RIDGID’s R4510 table saw really shines. Its sturdy workaday features, powerful motor and well-designed stand show that portability doesn’t have to mean compromise. This is an excellent woodworking choice for 10″ portable table saws.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
Consider whether you’ll be working inside or outside, on even flooring or dirt ground. You’ll want to choose the most convenient stand that’s sturdy enough for the kind of cuts you need to make. Pros should pay for a premium stand that doesn’t have any wobble whatsoever. DIYers and framers can probably make do with something lightweight and inexpensive.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.
Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.