We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.
Once again our team has put some serious time and effort into our Head-to-Head evaluation to bring you the most comprehensive information available. For this evaluation, we broke things into several categories including: Precision & Accuracy, Performance (power), Price, and Ergonomics. For each of these categories we’ll rank the saws and at the end we’ll name the Best Portable Jobsite Table Saw based on all the results combined.

When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.


Table saws are versatile enough to earn a spot in every home shop—even if that shop shares the garage with the family car. The market offers a range of saws, from $200 portable, less accurate saws to heavy and very accurate cabinet saws costing thousands. All the table saws shown here have 10-inch blades that can cut though stock up to 3 inches thick, and they meet the Underwriters Laboratories' safety standards to prevent kickback. Keep reading for an extensive roundup of table saws, from portables to hybrid models.
When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.
The DeWalt, Bosch and Ridgid saws have strong stands that are easier to set up, sturdy fences that lock down parallel to the blade every time, and smooth-operating blade controls. If you’re a contractor or an avid DIYer who just likes top-quality tools that feel good and last a long time, we think the extra few hundred dollars is a good investment.
Service can be expensive on these models, so you should see if the company will be covering repairs, of if you’ll be expected to foot the bill. Add-on plans are a great way to minimize your liability if something goes wrong. By purchasing a third-party warranty, you can have a much better customer service experience. The warranty provider will deal with the company for you, so you don’t have to negotiate or deal with frustrating runarounds.
This one’s compatible with Jet’s rolling bases. You can mount it on any of the company’s all-metal roller frames, and move it around your shop! That’s ideal for busy shops with a lot of large equipment and not a lot of space to spare. It’s also handy for home craftsmen who don’t have as much dedicated space as they’d like to devote to a table saw. The Grizzly, on the other hand, is much harder to convert to a wheeled base, because it has the dual extension tables.
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
Table saws can pose a serious risk of injury, since part of the spinning blade comes up above the surface of the table where it can come into contact with the user's hand as it guides the wood. Thanks to voluntary safety standards introduced by Underwriters Laboratories (UL) in 2007, pretty much all table saws now come with blade guards that minimize the risk. Modern guard systems are easier to remove and replace as needed – an important feature because inconvenient blade guards are apt to be left off the saw.
Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.

As accidents and injuries are common when using large power tools like this one, it’s important that you look for safety features such as a dust collection system. Inhaling the sawdust that comes off the wood can make you sick, but this system does a good job of removing the dust from your work area. The collection port itself has a convenient on the cabinet too.


All the articles on this website are short and punchy without much filler, but because there is so much to learn about table saws it will still take you the better part of an afternoon to read through them all. For those who don’t have that kind of time, or those who already know a great deal about table saws, this is the section that will take you to the best table saw for your needs.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.
There are a few nice conveniences which we don’t always see on affordable units like this. The Grizzly has a built-in miter guide, made from cast iron, which slides easily in the worktop. The left-tilting blade is coordinated with a digital display, which gives you an accurate, real-time readout on your bevel angle as you cut! The motor has a starting amperage of 13, which is safer for your breakers than 15 amp models. There’s a standard 4” dust collection port, and
It’s often overwhelming when looking for new power tools and products online. So many features, specs and brands etc to research and review. So, what should you look for when buying a new table saw? One thing we always mention is to make sure you read as many table saw reviews as you can before purchasing one, this will insure you have the best table saw for your requirements.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.

Now let’s talk power. The 15-amp motor is housed underneath the aluminum table and features replaceable brushes so you can expect long life from the saw. The gearing for adjusting the blade height also looked to be built with durability in mind and was well-greased. Cranking the height on the saw was simple and, unlike many saws I’ve used, even bevel adjustments were a snap and didn’t require a ton of effort to move the blade. We found that we could easily loosen the bevel lock and slide the assembly along its arc until we got to the required angle.


Dust collection can seem like an afterthought for jobsite table saws. The fact that you’re outside, often on an unoccupied site, negates the need to collect your dust. But breathing that stuff doesn’t do your lungs any favors. That’s why dust collection is so important. Of course, if you’re working inside or in an occupied structure, collecting all that dust will make the cleanup part of your day easier to deal with. Since we’re not talking about concrete dust regulations, even a standard shop vac will be a good bet to help contain the mess.

One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
With a single cast iron trunnion system, the Delta UNISAW offers dependable accuracy, smooth and continuous operation, but also vibration free control. Thanks to the fact that it features a fifty-two inch fence system, it’s the perfect choice for woodworking pros, but also people who are just starting out in the woodworking industry, such as hobbyists. Since it also comes with an upfront bevel dial to easily fine tune the blade level, you get a striking accuracy within a quarter of a degree, ensuring precision setups cut after cut.
Bosch GTS1031 10 in. portable jobsite table saw is powered by a 15 Amp motor that allows this table saw to rip through any lumber or hardwood quickly and easily. Bosch’s Smart Guard System provides added control while cutting, SquareLock Rip fence ensure consistent and accurate cuts, and an all steel base provides added durability. Oh yeah, and we forgot to mention the price. This is the most affordable table saw on our list!

It is not a cabinet saw, so judging it by those standards would be unfair. As a portable job site saw this is amazing. Loud and dusty, sure, but that is expected. Easy to use and store, yes. The fence is square to the blade, and is rock solid, as long as you make sure the nut at the back of the fence is set right. The fence is not quite square to the table top, and I can't tweak it, but for construction I wouldn't care. I do other fussier things on the saw, so I will shim out an auxiliary fence. I made a cross-cut sled, which I recommend, and get thin kerf blades. I got a rip, general, and fine finish blades, and I get great results.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
×