The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
The design is quite good. The SawStop safety system ensures smooth and flawless operation while protecting you from a variety of hazards. However, regardless of the safety aspects, you should always wear protective equipment, especially gloves and goggles. One of the most notable things about the design is the fact that it provides 99 percent dust collection both below and above the table. The riving knife maximizes kickback and also offers protection.
As far as performance, the fence could be a bit better in its locking in – square front to rear – but you get used to being able to set it square and use the rear adjustment knob so that it stays put. Some folks have complained about motor burn outs – but having experience now with 17 saws – over 6 years or more – I haven’t encountered the problem (maybe we’ve been lucky?)

The miter gauge gets an “its fine” grade. Ok to support a narrow piece for a crosscut, but not long enough to do much more than that. I upgraded to an Incra miter 1000SE and never looked back. Although a crosscut sled is pretty easy to make (and I highly recommend getting one) I picked up an Incra Miter Express sled for real cheap at a garage sale, so I am happy to use that.


Carrying things standing on end is easier, since it makes for a narrower package that can easily fit by your side. You’ll be able to lift a heavier saw less awkwardly in that position than if you were to carry it out in front of you. You’ll also want to think about size in terms of where you need to fit the saw in the vehicle, and where you’ll be storing it when it’s not in use.
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.
The blade guard is the most noticeable and the most important safety element of every saw. Its purpose is very simple – it keeps your fingers away from the blade. Many people decide to unscrew this part and take it off to speed up the cutting process, but that’s a huge mistake. In fact, a massive percent of injuries happen because people alter the safety mechanisms in order to work faster. Risking your life for a few hours of effective work isn’t worth it, to say the least.
We recommend something with this technology for new woodworkers, instructors, or folks who work in a busy shop with lots of movement around them. They’re also a safe bet for buyers who simply like to take as many precautions as possible. The only downside to these systems is the price. You’ll find them on machines closer to the $3,000 mark, as a rule.
We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.
In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.

There are a few nice conveniences which we don’t always see on affordable units like this. The Grizzly has a built-in miter guide, made from cast iron, which slides easily in the worktop. The left-tilting blade is coordinated with a digital display, which gives you an accurate, real-time readout on your bevel angle as you cut! The motor has a starting amperage of 13, which is safer for your breakers than 15 amp models. There’s a standard 4” dust collection port, and
In terms of cutting results, Craftsman’s 28463 Jobsite Table Saw made a decent showing. It delivered accurate rip cuts, kept its bevel setting for angled ripping and could handle a stacked dado blade without laboring. Dust collection through an enclosed shroud was on par with more expensive machines. I also appreciated the saw’s clear, split guard and a riving knife system that is easy to install and adjust up or down. These are the plusses of what, in this test, is the budget-priced tool.
The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a tool-less assembly of the riving knife and anti-kickback pawls. There is a large easy to ...  More + Product Details Close

The DEWALT DW745 and the Bosch 4100 both have 15 amp motors, so power shouldn’t be a problem with either of these job site table saws. The DEWALT has a high torque motor that is capable of delivering a no-load speed of up to 3,850 rpm. The Bosch 15 amps and a no-load speed of up to 3,650 rpm. The difference between the two is not something that would be noticeable without sophisticated equipment, and will not affect performance in any significant manner. The noticeable difference between the two is that the Bosch 4100 comes equipped with a soft start motor that is lacking on the DEWALT DW745. This will cause a noticeable load on your power source, and may affect other tools and lighting attached to the same source during startup.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.
×