All the articles on this website are short and punchy without much filler, but because there is so much to learn about table saws it will still take you the better part of an afternoon to read through them all. For those who don’t have that kind of time, or those who already know a great deal about table saws, this is the section that will take you to the best table saw for your needs.
All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution. 

We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
Blade guards are an important safety device and should never be removed from the saw. You want to find one that rises up parallel to the table so it is always on top of the material you are working with. The purpose of this blade guard is to protect you from the spinning blade. While some woodworkers find them annoying, the safety they provide is well worth the inconvenience.
As with the smaller Dewalt we’ve recommended, this one has very inconsistent quality control on the table. Some reviewers cited units with bowed, funky surfaces, while others got units that were perfectly flat. that’s a flaw of the molding process. We also have a bone to pick with Dewalt as far as the coating on these. While we understand that the coating is supposed to help wood slide better, it just doesn’t seem to last very long or hold up well. It also has the same flawed warranty coverage. We’d recommend purchasing add-on coverage.

Unlike a lot of competing models, this one is updated regularly. Previous buyers appreciated the thoughtful tweaks, which made it clear that Dewalt listened to feedback from folks who used the first versions. Recent buyers noted the improved rack and pinion teeth, which help the fence lock into position with less play. They also appreciated the reinforced rails, which felt a lot less flimsy than the old version.
Apart from some short reviews, we’ve also covered some other aspects such as safety and proper use of these tools. Make sure you thoroughly read our articles because they could save your life. The tips we offered are well-known among the professionals, but beginners are always susceptible to various risks, especially if they don’t know how to handle these tools properly.
The blades are categorized according to number of teeth, diameter, arbor size, kerf size, application and speed. They can also be divided by material. Regular commercial table saws are 10-inch or 12-inch. Teeth usually number from 24-80. Many blades are tipped with diamond, carbon or carbide. This lets you cut through more than just wood. You will also need to think about the tilt of the blade. They are available in left tilt or right tilt. With a left-tilting hybrid or cabinet saw, the motor cover can get in the way of the sliding table. Router table extensions don’t work well on left-tilting saws. 

You often find that many contractors have a love hate relationship with blade guards. Many contractors and woodworkers simply find they often get in the way and can often get wood stuck in them. But many manufacturers are improving these guard’s year on year and now many of them are very advanced and will help keep your fingers from getting hurt, we always advise you to consider the table saw blade feature on any table saw in detail as it could one day help saw you.


Lack of mobility is the cabinet saws major drawback. Some cabinet saws need proper electrical wiring set up and often weigh a huge amount because of cast iron table tops and full cabinet like stands. But if your setting up a new wood shop or have a work space or wood shop of your own then there is no better investment you can make other than purchasing a cabinet table saw.
The DCS7485T1 60-Volt MAX 8-1/4 in. table saw The DCS7485T1 60-Volt MAX 8-1/4 in. table saw is maximized for accuracy capacity and runtime. The brushless motor delivers the power to cut all common materials the rack and pinion fence allows for fast easy adjustments and provides the capacity to rip 4x8 sheet goods. The DCS7485T1 comes with 1 ...  More + Product Details Close
Setting up both saws was quick and easy, since their factory-adjusted blades and fences were square and parallel to the tables' miter gauge slots out of the box (this is one of the reasons to buy a $350 table saw over a $100 one). Both saws had similar setup procedures: Attach the fence, raise the riving knife, attach anti-kickback pawls and attach the blade guard. There is no on-board stowage space for the DW745's rip fence, but this does not really affect the setup time or effort by much.
I was hoping to see the JET in there. But glad you didn’t waste your time with it. I bought it a year and a half ago and it’s a piece of crap. It has not held up at all, I keep it in my construction trailer and it has its own cubby hole and is secured with straps. It has fallen apart. The fence has no adjustments and is off 1/4” front to back, From the factory. I have to spend so much time trying to adjust rip fence, and then I can’t turn my guys loose with it because they won’t take the time to adjust and check for accuracy. Just really disappointed in the product. I am waiting for the testing done on the cordless saws because I am upgrading.

Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.


Excellent saw. Got here sooner then expected. Fairly simple to put together. Folding stand is very solid and easy to operate. Takes up very little space in my garage. I've never owned a table saw before so I'm easily impressed. Some other buyers recommended upgrading the blade, which I did. The blade it came with was ok but the Freud 10 in. 40 tooth Premier Fusion makes a very smooth cut. I haven't hooked up dust collection to it yet but it seems like it would work great. The scale for the fence is spot on. I would highly recommend this to any diy.
This portable jobsite table saw head-to-head includes 8 saws from; Bosch, Delta, DEWALT, Hitachi, Makita, Ridgid, SawStop and Skilsaw. Originally, we had also to include Ryobi as a budget friendly option for DIY’ers or guys just starting in the trades. However, we were not able to adapt that saw to our testing rigs so we pulled it from the testing (you may see some photos with the saw but again we’re not including it in the results).
The DCS7485T1 60-Volt MAX 8-1/4 in. table saw The DCS7485T1 60-Volt MAX 8-1/4 in. table saw is maximized for accuracy capacity and runtime. The brushless motor delivers the power to cut all common materials the rack and pinion fence allows for fast easy adjustments and provides the capacity to rip 4x8 sheet goods. The DCS7485T1 comes with 1 ...  More + Product Details Close

Plus, the machined aluminum table is our favorite on the market right now. It also has a smarter motor system than either of the Dewalt’s, thanks to a soft start and automatic speed control to ensure smooth cuts. However, it’s the slowest of the pack, and it doesn’t have quite as good a fence as the yellow competition. We think it’s a great choice for pros who are concerned about accuracy, but can’t spend lots of money on their unit.
Both of these table saws have a port that connects to a shop vacuum for dust collection. The DEWALT features a 2.5” port, while the Bosch has a 2” port. However, neither seems to do all that great a job. The Bosch might fare a little worse as far as the dust port clogging, but the DEWALT has some problems in this area, too. The Bosch is said to spew sawdust on the floor as though there was no dust collection port at all. The DEWALT racks up some complaints about the same problem.
These are the best choice for long jobs where you’ll get yourself set up at a job site, and need a saw that enables you to make all your big, long cuts without traveling back and forth between the site and your shop. While you won’t want to move these units around frequently, they’re great for seeing a contract through to the end from the worksite.
Even though is seems pretty irrelevant, the position of the On/Off switch is quite important, especially if you’re a frequent user of these tools. In today’s models, the switch is usually leveled with your knees. The main thing you should look for is the size of the OFF switch. It has to be big enough so that you can turn the unit off immediately either with your knees, elbows, or hands. The so-called panic button is one of the crucial elements of every unit, even if it doesn’t seem like it.

The price is acceptable. One cannot say it’s a cheap piece of equipment because it’s not. But, the high quality of production and a great deal of precision justify the somewhat premium price. If you’re a devoted professional, the price shouldn’t be much of an issue for you. The only downside many people reported is the quality control within the company. Many models came with broken or missing parts.


Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, over sized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
One shouldn’t expect a massive amount of storage, but being a table, it does offer some level of free space. In fact, some models even offer space for fences, gauges, blades, and other necessary equipment. Apart from that, you can always keep the necessary tools in the reach of your hands. It will make the process much easier and also a lot quicker.
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.

This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.

The Bosch 4100-09 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker.. It includes Constant Response circuitry to help maintain speed under load, and overload protection. The Square Lock rip fence is engineered for maximum trueness and great ease-of-use, with the fence able to easily glide along the rail for one-handed operation. The lighter GTA47W Gravity-Rise Wheeled Stand has 8 In. treaded rubber-composite tires and a single-action design for easy set-up and transport. It is jobsite-ready with heavy-duty construction. The Smart Guard System is the first modular table saw blade guard, featuring a three-position adjustable riving knife, anti-kickback pawls and non-obstructed-view barrier guard assembly. The table saw provides a 29 In. x 21-1/2 In. square tabletop with a 25 In. rip capacity for ripping 4 Ft. wide sheets goods in half.

Balancing heavy-duty durability and lightweight design, this machine proves that good things can come in small packages. While buyers are overall happy with their purchases, they do seem to all agree on one thing: the DEWALT DWE7480 may be an overall investment, but it could seriously do with a miter gauge replacement. Buyers report replacing its inaccurate, plastic gauge for a solid, more detailed one.
Next, the rip fence is pretty hard to adjust also, and mine had a few thousandths of a bow, but that bow is way within industry standard for a portable saw. Here's what you do: First, check it for parallel, you might get lucky. (On a side note, there is a fine line between how tight to set the locking arm adjustment screw with this rip fence. Too tight, and when you lock it, you'll loose the self-adjustment feature, too loose isn't good either. Adjust the screw (on the rear of the fence), to where the fence self aligns while still getting tight) If you are like me, mine was 15 thousandths out, then unlock the locking handle and loosen the two screws on top closest to you in THIS ORDER! Loosen the screw closest to the lock handle first, and for a few turns. Next, loosen the screw that is about 6 inches away toward the middle just enough to where the fence will rotate on this screw, but not so much as to be sloppy. Begin experimenting. Pivot the fence back and forth, running your measuring device up and down the fence until you get pretty close. Lock handle and checking for parallel. Again and again. When you finally get pretty close to parallel, then lock the lever and experiment with locking both screws. If it doesn't move and you are within a few thousandths, then voila, you are done with adjusting the blade and rip fence for parallel. The other adjustments are straight forward, and once set up, THIS IS A GREAT SAW!!!!!!!!!!!!!! Good luck, hope this review helps
The Steel City 35955 also comes with a new table insert system, a seamless table top that offers users a flat surface on which they can work on, but also the Push Stick safety system which prevents injuries to the fingers while using the table saw. Warranty wise, you get 2 years limited warranty, which is enough to give users peace of mind that they’re covered for a long time.

For centuries, the job of the sawyer was, quite simply, to saw logs into lumber. Working in two-man teams, a pair of sawyers would use massive saws -- called whipsaws or pitsaws -- to cut felled trees into workable planks with their own muscles as the motive power. The job was exhausting and often dangerous, yet necessary to create the precious lumber used to build everything from homes to railroad bridges.
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.

Hybrid table saws are the latest thing on the market these days. They’re in between contractor and cabinet table saws in terms of price, power, and precision. These have either half-cabinets or cutaway stands like a contractor saw, but with the super-powerful motor and improved stability of a cabinet unit. They’re heavy, so you should be prepared to use them on a wheeled lift, but they can be transported fairly easily if you have helpers.
Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.

The first is how easy the switch is to operate. Oftentimes, you will approach your table saw with your hands full especially when we are talking about sheet goods. And sometimes you’ll be making cuts that require both hands to be occupied. Now if something goes wrong or you need to turn the saw off for any reason, you need to be able to do so and the quicker the better.
For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.
Cabinet models are stationary, as a rule. They’re not designed for portable use, and you should plan on keeping them in your shop for their working life. However, some models are compatible with optional wheeled bases, and these are great for folks who want to be able to move their table saw around the workshop, without sacrificing any power, build quality, or stability.
And finally, they all include a blade guard that can be removed and reinstalled without tools. Because a few sawing operations, such as non-through cuts, require you to remove the blade guard, we like saws that make this task easy. The Bosch, DeWalt and Ridgid saws have well-designed blade guards that are easy to remove and reinstall. The blade guards on all but the Porter-Cable and Craftsman also have a feature that holds the blade guard in the raised position to allow better blade visibility for setting up cuts.
Like the Bosch, this Dewalt comes with a rolling stand. It’s convenient to set up and take down, since you can do it without helpers or tools. It rolls like a dolly, and opens into a nice, sturdy table. We especially like the splayed legs, since they lend the whole thing a bit more stability than the Bosch version. Unlike the Bosch’s stand, the Dewalt’s has semi-pneumatic tires which won’t ever go flat.

As with anything, it’s easy to get overwhelmed with the variety of types, sizes, features, colors, weights, what, when, why, where, who…(let me catch my breath). For now, let’s focus on what’s right for you with our Best Portable Table Saw Guide. We’ll start by identifying quality brands that align with your needs. Besides, who wants to buy something that won’t work?


Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
Richard Romanski of Popular Mechanics names his five favorites among 15-amp portable table saws. A slideshow outlines what he likes best about each saw, as well as any downsides. Although it's clear that Romanski has tested these saws hands-on, he doesn't go into any details about his testing methods or name the other saws that didn't make the cut.
The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.
The weak point of this rolling stand is the base where all the weight sits. I really like the Bosch rolling miter saw stand, which is what convinced me to buy this setup. When you compare the miter saw to this table saw, it's a night and day difference. The miter saw from Bosch has thicker and larger diameter metal tubing. It clearly weights more, but it's on wheels, and has yet to show any fatigue from constant use.
If you’re looking to use a wheeled base, you’ll want a standard rectangular unit, not a cabinet with multi-directional extension tables. Double check to make sure the model is compatible with wheeled bases, and make sure you buy your base from the same manufacturer, so you have a guarantee that they’ll work together. No matter what, don’t skimp on your base! Remember that the frame and wheels have to hold up a machine that weighs 1/4 ton or more, so it needs to be incredibly sturdy.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
You have to know the amount of money you are willing to spend for the right saw. The truth is that the price will vary significantly depending on where you are buying the saw, the brand and the features it comes with. However, with a good budget, you can easily narrow down the options you may have. You will have a smaller range to work with and you will know what features to expect within that price range. Always be willing to spend a little more on the table saw you want in your workshop especially if you work on wood every day.
×