To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.
For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.
When using the side extension, a tape moves along so you won’t have to remember what measurement to lock the fence on or read a double marked measurement guide. It’s an innovation we like, but there are questions as to the long term durability of the tape itself. Like Ryobi, Ridgid uses a magnetic throat plate to secure it while leaving access simple.
The fence on a table saw is one of its defining features and allows for precise, square, and repeatable cuts. Not all fences are equal though and a poorly built fence is a deal-breaker, in my opinion. Not only will a poorly built and implemented fence affect the quality of your cuts, but a fence that moves or is not square to the blade can cause your material to bind and kickback.
Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.

This saw is great. I needed a portable saw that was accurate and this fit the bill. All I can say is BUY THIS SAW if you are in the market for something portable. It has everything you want in a table saw. Dust collection is good with a shop vac and I like that the miter gauge is full size and not a ‘mini’ one that come with most portable saws. The fence is aluminum with built in T-track which is very nice. It’s quiet and has a soft-start. I was especially impressed with t...
The weak point of this rolling stand is the base where all the weight sits. I really like the Bosch rolling miter saw stand, which is what convinced me to buy this setup. When you compare the miter saw to this table saw, it's a night and day difference. The miter saw from Bosch has thicker and larger diameter metal tubing. It clearly weights more, but it's on wheels, and has yet to show any fatigue from constant use.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.

The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.

To learn about how table saws perform in real people's homes, we consulted owner-written reviews at retail sites like Amazon, Home Depot, Lowe's, and Sears. User reviewers don't have the breadth of experience that many experts enjoy, but they can provide keen insights on the model they bought, including things that might not crop up in the relatively short time professional reviewers have to spend with a given saw.

Table saws are undeniably the kings of rip cuts on the jobsite and in shops. The concept is simple: Place a motor below a solid table to turn a blade somewhere in the 4000-5000 RPM range through the surface and watch the sawdust fly. The idea may be simple, but the reality is much different. How big should the table be? What size blade should you use? How heavy can you get away with making it?
Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
We absolutely love the Dewalt DWE7491 that we recommended as our top quality choice above. It’s a powerful, precise workhorse that can handle nearly any cutting job. However, times are changing fast, and workplace safety standards are increasing just as rapidly. If you’re a professional who wants to stay on top of your code, you should consider getting a unit that’s equipped with a flesh-detections safety system.
Consider whether you’ll be working inside or outside, on even flooring or dirt ground. You’ll want to choose the most convenient stand that’s sturdy enough for the kind of cuts you need to make. Pros should pay for a premium stand that doesn’t have any wobble whatsoever. DIYers and framers can probably make do with something lightweight and inexpensive.
Clint DeBoer When he's not remodeling part of his house or playing with the latest power tool, Clint enjoys life as a husband, father and avid reader. He has a degree in recording engineering and has been involved in multimedia and/or online publishing in one form or another for the past 21 years. In 2008, Clint was one of the founders of the Pro Tool Reviews online magazine. He hopes his efforts at PTR will provide builders and contractors with reliable and engaging tool reviews to help them make better tool purchasing decisions.
Both saws were almost equally quick to setup for use, with the DeWalt coming out slightly ahead. The throat plate, which is thicker and sturdier than Bosch's, is slightly easier to remove and reinsert. The DeWalt's blade cavity offers greater clearance, which makes locking down and loosening the riving knife easier without scraping a knuckle. Dewalt's riving knife adjustment required less wiggling and hunting to get it set properly.
TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
The continuous-read, tape measure–type scale is ingenious and easy to read, and Ridgid’s lifetime warranty covers it against breakage. The Ridgid saw has the most versatile miter gauge with holes and slots for mounting extensions and accessories. The designers have cleverly fashioned the stand to also serve as a left-side outfeed support for ripping plywood.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.

On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
These saws are the most difficult ones to categorize. The simplest explanation would be that they are somewhere in the middle between contractor and industrial cabinet saws. They are driven by an inboard belt motor. These units usually have open leg stands, but there are some models with closed ones – hence the whole confusion and difficulty in categorizing.
When I switched blades, I did find the locking lever for the riving knife very stiff … not sure why. It raises to release the riving knife and pushes down to lock it. I resorted to gripping the lever with a pliers to manipulate it, after nicking some skin on the blade teeth. But, on the softer side, RIDGID provides a nice complement of overmolds on the miter gauge handle and blade height handwheel knob.
First, consider the types of cuts you’ll need to make, and which types of stock you work with on a regular basis. Think about the largest rip cuts you need to make, and get a cabinet saw with a suitable max capacity for rips. Find the thickest stock you need to cut, and make sure your new machine has a high enough depth capacity to make the cut cleanly. The larger your average stock, the larger a workspace you’ll need on your new cabinet unit. It’s also a good idea to think about bevel and miter cuts which you’ll be making on your table saw. All of our recommendations have the capacity for both, but some come with miter gauges and others don’t.
One drawback is because of the way the blade is stopped, you will want to have an extra blade brake on hand because once it’s used, it cannot be reused. So, if you don’t have another handy, you will have some downtime. Also, the stopping of a blade moving at thousands of RPM can understandably be very hard on the blade itself. Often, the blade may need to be replaced after it has been stopped in this way. Still better than losing a thumb.
Ridgid’s fence is outstanding for its design. Its large front plate helps stabilize it and the whole thing just feels solid. There’s very little play compared to some of the others and we were consistently able to lock it down perfectly square. We like the pinion style bevel adjustment. It’s not quite a good as a separate adjustment wheel, but a great improvement over simple sliding. We also like the independent locks for both height and bevel. It’s not often that a height lock would be required, but there’s an element of confidence that comes from knowing it won’t be going anywhere.
Apart from some short reviews, we’ve also covered some other aspects such as safety and proper use of these tools. Make sure you thoroughly read our articles because they could save your life. The tips we offered are well-known among the professionals, but beginners are always susceptible to various risks, especially if they don’t know how to handle these tools properly.
More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.

Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.

This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.
The first step to take when using a table saw is to don all the appropriate safety gear that a responsible operator should use. This includes, at the bare minimum, eye protection and thick work gloves. It's also a good idea to protect your ears with ear muffs or earplugs and to consider a mask that will cover your mouth and nose to prevent the inhalation of fine saw dust particles.
One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.
As power tool nerds, we’re always on the lookout for the latest and greatest developments in the market. One of the most exciting new products to come out in the past decade or so is the hybrid table saw. We think they’re an excellent space and money-saving alternative for home woodworkers who can’t make a cabinet saw work for their circumstances. They’re also a great portable option for folks with bigger job site requirements who have the ability to transport larger tools to off-site applications. One of our current favorites is this Shop Fox:
As for various accessories and attachments such as rip, miter and blade guard, these can be stored in their own specially designed hangars. If you plan on using other blades (and you probably will) there is also a well where you can store all the blades you have. In order to keep the surface of the table dust-free there is a dust collection port featuring a shrouded design which can be attached to the vacuum.
I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
×