Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.
Portable saws are usually light and smaller than the other types. The three basic types of portable saws are compact, bench top, and jobsite saws. Because they are designed for portability, the materials of which they are made sometimes lack sturdiness and stability. However, that’s not a reason to be alarmed; a vast majority of these units are absolutely safe for work.
RIDGID’s 94-lb. R4510 might not be a saw you want to lift into a truck bed every day, but it’s bound to deliver solid cutting results once you reach your destination. For starters, this saw includes a downright great stand. Step on one lever, and the tubular frame lifts and glides smoothly up into place. The same lever collapses it. It’s sturdy, well-balanced and provides a wide stance to keep the saw from shifting or tipping. Large wheels and rubber tires roll the machine around easily during transport or just to reposition it when set up. The left-most tube is both a working-height handle and side support for balancing extra-long crosscuts. Smart.
In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
Choosing the best portable jobsite table saw wasn’t an easy task but we’re confident we’ve done a thorough evaluation. In a very close race for the best table saw Hitachi beat out the DEWALT which came in second place followed by Skilsaw in third and Makita in fourth. It’s very interesting that the Hitachi and DEWALT look extremely similar. Hitachi edged out the DEWALT in performance and price resulting in the final scores. Skilsaw beat out Makita for the 3rd place only slightly and that result is really a function of pricing.
Sometimes picking a “Best Bet” is a real tossup, but not this time. While Bosch’s 4100-09 doesn’t disappoint, and DeWALT has what seems to be a bulletproof portable, I think RIDGID’s R4510 table saw really shines. Its sturdy workaday features, powerful motor and well-designed stand show that portability doesn’t have to mean compromise. This is an excellent woodworking choice for 10″ portable table saws.
Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
Cabinet table saws are the best choice for full-time professional woodworkers with a dedicated workshop. If you have a spacious shop, these are some of the most efficient, versatile cutting tools you can buy, especially for larger stock. With 3+ HP motors, they’re by far the most powerful machines you can get your hands on. Plus, their heavy, machined build quality gives you a precision and smoothness in your work that really compliments the professional. They have the most effective dust collection systems of any table saw, and durability that can last more than a lifetime.
Unlike a lot of competing models, this one is updated regularly. Previous buyers appreciated the thoughtful tweaks, which made it clear that Dewalt listened to feedback from folks who used the first versions. Recent buyers noted the improved rack and pinion teeth, which help the fence lock into position with less play. They also appreciated the reinforced rails, which felt a lot less flimsy than the old version.

Cutting dadoes can be done with a dado stack blade. I use the Freud 208. Blade changes are easy, and there is a lever that locks the blade in place so I can get a good yank on the nut with the included (and stored onboard) wrench. There is an accessory throat insert for the dado blade stack, but the standard throat will easily handle a ¼ thick stack, which is what I usually use.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.

While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.

Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.
As far as the design goes, cabinet saws don’t look much different from the hybrid ones. However, when it comes to sheer power, this type is the most powerful one in every regard. Therefore, devoted professionals who work on massive heavy-duty projects usually prefer cabinet saws over anything else. Each element of a cabinet saw is constructed to withstand a lot of stress and pressure.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
It has the widest rip capacity of the three. This one can handle materials up to 32 1/2”, which makes it ideal for folks who work with sheet stock on the go–especially when you consider the extra 22” you’ll have to the left of the blade. That’s thanks to the same rack and pinion fence as the smaller Dewalt. It’s even better on a larger scale, where the differences between this design and the sliding rail style you find on Bosch become very apparent. Reviewers agreed that this one felt much sturdier, smoother, and locked more securely than other portable units.
By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
If you work with wood in any capacity, chances are you rely on a table saw to make clean, accurate cuts. But when your good old saw goes to the big toolshed in the sky, it’s time to opt for a replacement. Before you dish out your hard-earned money on the first model you come across, remember that a table saw is a big investment, so it’s in your best interest to look into the many technical specifications of each option before you settle on a final purchase.
I’m trying to replace some lost tools for a doctor inflicted, lawyer cowardice sustained injury. I’ve been a woodworker for more years than I might imagine I am comfortable with saying simply for it seems to have been bestowed upon me from birth. The only comment I have is a general comment. As I’ve noticed from about 20 years ago being introduced do officially being educated at a local community college, everyone there had prestige rights attached to it, a couple of cabinet makers I worked for did also that Porter Cable was the Cadilac of woodworking tools. Well, China… Read more »
Give yourself a reason to smile every time you enter in your workshop by investing in this powerful instrument. DEWALT as a company guarantee quality in all their products for the interests of customer satisfaction. This Jobsite table saw is not exceptional. Its designed to provide precision and last longer. The saw features pinion and rack system that makes adjusting the fence easy and convenient. In other words, you will not strain or shift your concentration while on work. The table saw is designed with a rolling stand that guarantees you professional performance in all your cuts. It also features telescoping fence rails that retract and extend for a small portable package of the saw. Additionally, the table saw is suitable for both wide and narrow rip cutting as the fence can adjust based on the type of material you are cutting. Using a 15amp motor, you are sure that the saw will get the job done within minutes and save you energy cost.
×