A table saw is a powerful tool that makes short work of even large pieces of lumber, allowing you to make rip cuts down the grain of boards, beams, and even entire sheets of plywood. No carpentry shop or professional construction site is complete without a table saw. Deciding which saw is best suited to a given home workshop, furniture production factory, or building site is an important decision and merits careful consideration.

This Portable Table saw includes an industry standard This Portable Table saw includes an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a Tool-less assembly for the riving knife and anti-kickback pawls. It's perfect for mobile contractors and the Do-It-Yourself ...  More + Product Details Close
It’s just as powerful as our other recommendations. The SawStop has a 3HP belt-driven motor, and like the Jet, it uses a tweaked multi-belt drive system to transfer maximum power from the drive shaft to the blade. That makes for as powerful a cabinet saw as any on the market. This one slices smoothly through anything you can feed into it. It also has a slightly thicker max cutting depth than our other recommendations, so it’s the better choice for sturdy stock.
The Grizzly, like the other cabinet models you’ll see here, requires a 220V power supply. If you’re a professional woodworker, you probably already have a 220V hookup. If you’re a home woodworker or DIYer, you’ll need to have one installed, if you haven’t already. It can be an expensive installation, so factor in the cost when you consider how much you’ll spend on your new saw.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
I’m trying to replace some lost tools for a doctor inflicted, lawyer cowardice sustained injury. I’ve been a woodworker for more years than I might imagine I am comfortable with saying simply for it seems to have been bestowed upon me from birth. The only comment I have is a general comment. As I’ve noticed from about 20 years ago being introduced do officially being educated at a local community college, everyone there had prestige rights attached to it, a couple of cabinet makers I worked for did also that Porter Cable was the Cadilac of woodworking tools. Well, China… Read more »
A dedicated writer and communications professional spending his days lost in the intricacies of both proposal and freelance writing. When not sharing the knowledge of both fully and self-insured medical benefits to employer groups of all industries within California, Jeff Newburgh can be found at home spending time with his family and 3 dogs, pondering the next chew toy to be thrown, while kicking back and relaxing with a nice glass of red wine.

Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.


You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.

I definitely give this one 5 stars, but this is specific of the application – it being portable. If I was comparing it with other Hybrid saws, than this one doesn’t really compare when it comes to power. That being said. I was shopping for a table saw, after many years of working with a circular saw, and a straight edge – for me – it was time to get a setup for repetitive cuts that would be easier, and less time consuming (not to mention more precise, as the machine...
One of the biggest perks of a cabinet table saw, aside from the rugged construction and wide worktop, is the sheer power of the tool. You should expect a cabinet table saw to cut absolutely any stock within its depth capacity smoothly and easily. Look for motors with at least 3 HP, and sophisticated belt drive systems which translate that grunt into 4000+ RPM blade speeds. Don’t accept lesser power ratings on a cabinet model: these are the gold standard of table saws for a reason!

As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.


Replacing the hugely popular outgoing W1824, the W1851 is a brand-new Shop Fox hybrid with the same enclosed cabinet as you’ll find on the W1819 alongside features more in line with a contractor’s saw. We chose to review the W1851 as it’s a more flexible option than the W1819 and appeals to a broader range of woodworkers. We rarely review brand new products but in this case we made an exception… With a brand like Shop Fox, it’s not a case of taking a chance but of betting on a winning team.
If you need to move your saw around, it comes with a table saw stand that you can put up and down with ease. Fashioned from aluminum pipes with wheels that can handle uneven terrain, move around site without breaking your back. As well as its user-friendly nature, the stand can be stored away vertically so it’s a real space-saver whether at home or on the jobsite.

But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.
The miter gauges on these saws range from downright flimsy to cabinet-saw quality. All the saws except the Craftsman and the DeWalt also have T-tracks—a nice feature that captures the miter gauge bar, making it easier to start wider crosscuts. Because the Ryobi and DeWalt saws don’t have a standard miter gauge slot, you can’t use accessories that require a 3/4-in. slot.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
×