It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
Even a newbie can go around the table saw section at the local home improvement store and feel that some saws have easier adjustments than others. Some are simply easier while others are downright innovative in various ways. Porter-Cable came out of the value group for the overall win with adjustments that are both smooth and intuitive. Dual adjustment wheels mean that you’ll be able to accurately adjust your blade height and your bevel angle—a feature no other saw in this group has.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
The Shop Fox W1819 also comes with a miter fence with flip stop which provides excellent workpiece support and is great for longer workpieces. As for the flip stop, it’s going to be very useful especially when wanting to make several cuts of the same width. If you want to cut longer workpieces, you can also flip it out of the way and then pivot it back down in order to make more cuts at the cutting width of your choice.
This blade shares many features that come standard on other Diablo blades. The carbide teeth are cut from Diablo’s TiCo High Density Carbide. Perma-Shield non-stick coating helps the blade move through material with less friction, reducing heat that can lead to warping in addition to corrosion. Diablo’s Tri-Metal Shock brazing process ensures the teeth stay in place much longer than other blades and can withstand impacts that leave other blades in need of a dentist.
The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.
Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
Due to the position of the motor, dust collection is often an issue with these units, especially in comparison to the cabinet type. However, an industrial vacuum is usually a small and worthy investment which should solve the issue effectively. The main advantage of this type is the fact that it’s much cheaper than its nearest equivalent – the cabinet type.
Let’s face it: guys get in each other's’ way at a job site. It’s not always easy to find room to work, so portability is a serious advantage when it comes to making the most out of your space. Luckily for the professionals out there — not to mention hobbyists who prefer to move around rather than work in the same spot everyday — RIDGID’s 15-amp table saw comes with a convenient mobile cart for stress-free transportation.
Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ...  More + Product Details Close
In terms of cutting results, Craftsman’s 28463 Jobsite Table Saw made a decent showing. It delivered accurate rip cuts, kept its bevel setting for angled ripping and could handle a stacked dado blade without laboring. Dust collection through an enclosed shroud was on par with more expensive machines. I also appreciated the saw’s clear, split guard and a riving knife system that is easy to install and adjust up or down. These are the plusses of what, in this test, is the budget-priced tool.
How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.
These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.
Measuring in at 19.9" x 23.4" x 13.4", the SPT70WT-01 is compact enough to fit into any aspiring handyman’s garage, but powerful enough to tackle anything you throw at it on the job site, meaning it’s an ideal entry-level table saw for the amateur hoping to turn his hobby into a career. Sturdiness, durability, and anti-kickback technology make the world’s first worm drive table saw a revolutionary machine. Satisfied buyers can’t get enough of this balanced wood-devouring behemoth.
DeWalt DWE7490X table saw is a pretty cool portable table saw. It’s a great blend of accuracy, portability, and power. Weighing only 58 lbs, this table saw might be pint size, but it’s not lacking power. It has an impressive 15 A motor, 28.5 in. rip capacity, 47 degree bevel capacity, and a cut depth of 3-1/8 in (at 90 degrees). Not bad for a portable table saw. Other features we appreciate are its tool free fence adjustments for convenience and its metal roll cage for extra durability. This package also includes a scissor style stand, which allows you to easily pack up this table saw and bring it with you anywhere the job takes you!
DeWalt DWE7490X table saw is a pretty cool portable table saw. It’s a great blend of accuracy, portability, and power. Weighing only 58 lbs, this table saw might be pint size, but it’s not lacking power. It has an impressive 15 A motor, 28.5 in. rip capacity, 47 degree bevel capacity, and a cut depth of 3-1/8 in (at 90 degrees). Not bad for a portable table saw. Other features we appreciate are its tool free fence adjustments for convenience and its metal roll cage for extra durability. This package also includes a scissor style stand, which allows you to easily pack up this table saw and bring it with you anywhere the job takes you!
For homeowners without the luxury of a huge garage to fit their enormous table saw, DEWALT’s DWE7480 is a compact alternative to bulkier machines with the same wood slicing power. Measuring 25.8" x 26.5" x 13.9", the DWE7480 hosts a 15-amp motor that cuts at an unbelievable 4800 rpm with a ten-inch blade, meaning this small package packs big performance — and with adjustable rear feet that are designed to allow users to level their table saw on uneven surfaces, you’ll be sure to get a clean, precise cut every time, no matter how rugged the terrain. An additional dust port makes collecting your sawdust a breeze — especially if you attach an optional shop vac extension.

How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.
The miter gauges on these saws range from downright flimsy to cabinet-saw quality. All the saws except the Craftsman and the DeWalt also have T-tracks—a nice feature that captures the miter gauge bar, making it easier to start wider crosscuts. Because the Ryobi and DeWalt saws don’t have a standard miter gauge slot, you can’t use accessories that require a 3/4-in. slot.
The continuous-read, tape measure–type scale is ingenious and easy to read, and Ridgid’s lifetime warranty covers it against breakage. The Ridgid saw has the most versatile miter gauge with holes and slots for mounting extensions and accessories. The designers have cleverly fashioned the stand to also serve as a left-side outfeed support for ripping plywood.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.
Being concentrated is extremely important. A big percentage of injuries happen due to the lack of focus at any given moment. Remember, if anything happens, it will happen in under a second. Naturally, you won’t have any time to react properly. Music is something that can be dangerous and relaxing at the same time. Some people love working while listening to their favorite tracks, but it significantly lowers your concentration level. Therefore, you should avoid listening to music while operating a heavy-duty piece of equipment.
Contractor units are the next step up from portable (or jobsite) table saws. A contractor table saw has a worktop and motor assembly that looks a lot like a cabinet model, only it’s missing the cabinet! Contractor units aren’t quite as portable as a job site saw, but they’re about half the weight of a cabinet saw. They pack a lot more power than a portable unit, and their cutaway stands make them fairly manageable for folks who have helpers to assist in getting the saw off the truck and set up at the site.

Dust collection can seem like an afterthought for jobsite table saws. The fact that you’re outside, often on an unoccupied site, negates the need to collect your dust. But breathing that stuff doesn’t do your lungs any favors. That’s why dust collection is so important. Of course, if you’re working inside or in an occupied structure, collecting all that dust will make the cleanup part of your day easier to deal with. Since we’re not talking about concrete dust regulations, even a standard shop vac will be a good bet to help contain the mess.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.

When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.

Cabinet table saws are the best choice for full-time professional woodworkers with a dedicated workshop. If you have a spacious shop, these are some of the most efficient, versatile cutting tools you can buy, especially for larger stock. With 3+ HP motors, they’re by far the most powerful machines you can get your hands on. Plus, their heavy, machined build quality gives you a precision and smoothness in your work that really compliments the professional. They have the most effective dust collection systems of any table saw, and durability that can last more than a lifetime.
We recommend something with this technology for new woodworkers, instructors, or folks who work in a busy shop with lots of movement around them. They’re also a safe bet for buyers who simply like to take as many precautions as possible. The only downside to these systems is the price. You’ll find them on machines closer to the $3,000 mark, as a rule.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
One of the biggest issues and potential hazards when working with table saws is kickback. Table saw kickback occurs when wood is ejected from the saw at extremely high speed. You can imagine the sort of injuries this can cause. Table splitters are effectively small vertical bits of metal or sometimes plastic that are designed to stop the wood flying back if there is a kickback.  Attached to the splitter are anti kickback pawls either side, they look like table saw blades themselves but they are in fact there to grip the wood at stick into it in case of kickback.

We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.

Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.

Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.
Buying a table saw is one of the biggest and most important purchases you will ever make when it comes to power tools. It is an integral part of most job site equipment, as well as an essential item for most do it yourself projects. Choosing a table saw that fits your particular needs and budget can mean the difference in both profitability and frustration level.
It can seem like plastic is a weight-saver on the part of the manufacturer, but it’s really a cost-saver. You shouldn’t accept shoddy build quality in the name of getting a lighter machine. While no portable unit will include heavy cast iron components like a cabinet table saw, you can find metal alternatives that offer rugged, long-lasting build quality. Instead of plastic, look for aluminum.
The miter gauge gets an “its fine” grade. Ok to support a narrow piece for a crosscut, but not long enough to do much more than that. I upgraded to an Incra miter 1000SE and never looked back. Although a crosscut sled is pretty easy to make (and I highly recommend getting one) I picked up an Incra Miter Express sled for real cheap at a garage sale, so I am happy to use that.
You’ll also want to consider which features are most important for you. If you need extra space to work, and cut lots of larger stock, you should invest more in a saw that gives you more room. If you’re working with people who haven’t spent their lives working with professional-grade tools, or if you’re trying to meet tough workplace safety standards, you should probably spend a bit more for a unit with a skin-detection system to protect fingers or limbs.
Jet also gives you different choices when it comes to the extension wings. Some customers prefer the cast iron wings because they add more weight and keep the table from shifting, but others prefer the stainless steel wings that are durable and easier to use. No matter which wings you choose, you’ll find that you can quickly and easily attach them to the table’s surface to extend the total amount of workspace you have.
If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.
×