Both saws provide great cutting performance, and should handle most homeowner and DIY wood-cutting needs with ease. The saws are marketed as job-site saws, meaning they're designed for construction and home-improvement applications where extreme precision and accuracy is not typically required. This does not mean they're poorly suited for fine woodworking, though. You might not achieve the same precision as with a full-size stationary table saw, but out test cuts were by no means sloppy. And upgrading from the simple miter gauges included with both saws to an after-market miter gauge (such as an Incra model) or a cross-cut sled should improve the accuracy of straight and angled cross-cuts.

It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.
Every woodworker knows the plague of working in a dusty environment. The SawStop has a fantastic dust collection system so you can enjoy your cutting without your eyes being strained. Almost all of the dust is wicked away both above and below the table. Up above, the blade does all the legwork and there’s a neatly designed shroud which pulls all this dust away from the blade. The 4-inch port means you can slip your shop vac on with no issues.        
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
Our biggest surprise while running the best table saw review tests was in the cutting power and the quality of cut: There wasn’t much difference among them. All these saws ripped through 3-in.-thick oak without hesitating. We tried this test with the stock blades that came on the saws. Then we repeated the test using a top-quality blade in each saw.
You will not always get your job within the workshop, there are moments where you will have to get out and work from a distant place. Therefore, you will require having a table saw that is portable and reliable for such duties. Rockwell table saw with a laser has large legs with wheels. You can easily pull it to any place comfortable as the wheels keep rolling. In other words, you will not have to struggle with the entire unit trying to lift it when you want to switch working positions. Additionally, this table saw has a foldable fence for convenient storage and also ensures there is enough room for all size material. The inclusive laser guide is to ensure you get consistency in accuracy. Once the blade is not in the position, the laser guide adjusts automatically for the benefit of the user.

​The saw does not easily detach from the stand. Sometimes it’s beneficial to set the saw up as a bench-top saw, but the DeWALT 7491RS doesn’t come with quick release levers to accomplish this easily. In this case, you would have to use a drill to remove four screws to detach it from the stand. I wouldn’t recommend doing this unless you have to because over time the screw holes will strip.
And finally, there are a couple of jobsite table saws running around with flesh detection to drop the blade out of the way if it detects a strike. There’s a significant premium in cost for these saws and there has also been plenty of litigation regarding whether it should be required on every table saw and whether more than one company has the right to manufacturer the mechanism. But they’ll save you a much worse injury in the event of an accident.
Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
A dedicated writer and communications professional spending his days lost in the intricacies of both proposal and freelance writing. When not sharing the knowledge of both fully and self-insured medical benefits to employer groups of all industries within California, Jeff Newburgh can be found at home spending time with his family and 3 dogs, pondering the next chew toy to be thrown, while kicking back and relaxing with a nice glass of red wine.

One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
×