We cannot emphasize enough how important it is to think about safety at all times while using these tools. Even the slightest mistake can make a difference between life and death. The worst part is the fact that it usually happens in an instant, leaving you no time to react at all. Therefore, whatever you do, don’t forget that there’s a thin line between you having ten fingers at one moment and 8 in the next second.
We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
For this portion of the testing and evaluation we used three different materials (3/4″ AC Plywood, 5/4 Mahogany Decking, and 5/4 Pressure Treated Southern Yellow Pine Decking) while measuring the saw blade RPM, and the saw motor AMP draw. To compare the saws we’re looking for how much blade speed each saw has under load, and also how much the amp draw increases under load. Think about it like driving a car, a more powerful car will not drop as much speed going up a hill and the engine won’t work as hard.
As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.

The maximum depth of cut on a saw tells you how thick of a material you can cut through cleanly. Be careful when you’re looking at depth of cut ratings, since you’ll usually find two separate specs listed. One is for cutting at 90 degrees, the blade’s normal setting, and one is for cutting at a 45 degree bevel, which is generally the furthest a table saw blade will pivot. Most of us will only need to be concerned about the 90-degree rating, but if you cut lots of angles, you should check the 45 degree rating as well.
Hybrid table saws are the latest thing on the market these days. They’re in between contractor and cabinet table saws in terms of price, power, and precision. These have either half-cabinets or cutaway stands like a contractor saw, but with the super-powerful motor and improved stability of a cabinet unit. They’re heavy, so you should be prepared to use them on a wheeled lift, but they can be transported fairly easily if you have helpers.
Some table saws go one better than a splitter. Splitters are fixed. They do not move along with the blade. It also needs to be removed if you’re making cross-cuts or dado cuts. A riving knife, on the other hand, is fixed to the same part as the blade. This means it can move along with the blade. Riving knives don’t get in the way either so this is the best option.
Another excellent choice for the hobbyist or at-home handyman, the SKIL 3410-02 10-Inch Table Saw is a great value, giving you a durable build and quality performance at a wallet-friendly price. It doesn’t have the same brand recognition as some of the more expensive options on this list, but reviewers love this machine and say that it’s perfect for woodworking and DIY projects.
You will agree that your ability to hold, controlling and manipulating the saw largely depends on your strength. Since small table saws are lightweight, you should go for a powerful table saw so as to avoid fatigue during small jobs. This also means that if you are working in a forest for a whole day the light weight is of great importance it also helps reduce fatigue. When shopping for chainsaws ensure the saw balances well in your hand. You should also ensure that you can easily shift the saws grip from hand to hand without losing its balance.
The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.
For those of you who are looking to up your DIY game but don’t have enough capital to make the Dewalt DW745 happen for your home shop, this Craftsman is a decent budget choice. It’s powerful, lightweight, and extremely affordable. We don’t think you should expect too much from this one, though, since it has a very light table and a fence that won’t line up quite as precisely as you’d need for furniture-making or professional-grade projects. It’s cheaply-made, and doesn’t have as user-friendly a design as our other choices. For the home carpenter, though, this should do the trick for all your basic framing cuts.

Measuring in at 19.9" x 23.4" x 13.4", the SPT70WT-01 is compact enough to fit into any aspiring handyman’s garage, but powerful enough to tackle anything you throw at it on the job site, meaning it’s an ideal entry-level table saw for the amateur hoping to turn his hobby into a career. Sturdiness, durability, and anti-kickback technology make the world’s first worm drive table saw a revolutionary machine. Satisfied buyers can’t get enough of this balanced wood-devouring behemoth.
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
DeWalt DWE7490X table saw is a pretty cool portable table saw. It’s a great blend of accuracy, portability, and power. Weighing only 58 lbs, this table saw might be pint size, but it’s not lacking power. It has an impressive 15 A motor, 28.5 in. rip capacity, 47 degree bevel capacity, and a cut depth of 3-1/8 in (at 90 degrees). Not bad for a portable table saw. Other features we appreciate are its tool free fence adjustments for convenience and its metal roll cage for extra durability. This package also includes a scissor style stand, which allows you to easily pack up this table saw and bring it with you anywhere the job takes you!
If height adjustments were standardized, we could expect each saw to make them nearly identically. Taking a look under the hood, we discovered several different methods—each with their own effect. Most of the saws employ a bevel gear system that provides smooth and reliable performance. We noticed that many used solid metal gearing, but Bosch used plastic for both the 4100 and the REAXX.
More power is also associated with more control. More control also gives you the ability to cut tougher materials. Furthermore, more control allows you to use bigger blades with ease. For instance, a 1500W of the motor will result in swift movement of the blade as it spins. High RPM of the blade gives the user a greater chance of achieving accurate and precise cut. So, when shopping for a table saw, look out for a skill saw with the higher motor rating.
This type requires a heavy-duty circuit because it’s driven by a powerful 3 to 5HP motor. The blade is driven by three parallel V-belts which ensure a smooth operation and an efficient transfer of energy. Needless to say, if you have big plans, you might want to consider investing in a high-quality cabinet saw. Prompted, it’s going to cost you a significant amount of money, but it pays out relatively quickly.

We were impressed with the Bosch Glide Miter Saw which was revealed in 2010 and revolutionized the depth required by a saw in close quarters. Building on their solution-based approach to products, the company has finally addressed the need for a truly portable full-power jobsite table saw. The Bosch GTS1031 table saw can be carried by its single handle, which is balanced in the middle, and all accessories are safely and securely stored on-board. This was demonstrated wonderfully by none other than Jason Feldner at the 2011 Bosch Media Event, who came running into the room with the Bosch GTS1031 table saw in one hand and a GTA500 stand in the other. Weighing in at a manageable 52 pounds, and this is one 15-amp jobsite table saw that does a great job of balancing portability and raw cutting power.

The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.

Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.
post-template-default,single,single-post,postid-5859,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
The miter gauge gets an “its fine” grade. Ok to support a narrow piece for a crosscut, but not long enough to do much more than that. I upgraded to an Incra miter 1000SE and never looked back. Although a crosscut sled is pretty easy to make (and I highly recommend getting one) I picked up an Incra Miter Express sled for real cheap at a garage sale, so I am happy to use that.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
Apart from some short reviews, we’ve also covered some other aspects such as safety and proper use of these tools. Make sure you thoroughly read our articles because they could save your life. The tips we offered are well-known among the professionals, but beginners are always susceptible to various risks, especially if they don’t know how to handle these tools properly.
Buying a table saw is one of the biggest and most important purchases you will ever make when it comes to power tools. It is an integral part of most job site equipment, as well as an essential item for most do it yourself projects. Choosing a table saw that fits your particular needs and budget can mean the difference in both profitability and frustration level.

While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.
Dust collection can seem like an afterthought for jobsite table saws. The fact that you’re outside, often on an unoccupied site, negates the need to collect your dust. But breathing that stuff doesn’t do your lungs any favors. That’s why dust collection is so important. Of course, if you’re working inside or in an occupied structure, collecting all that dust will make the cleanup part of your day easier to deal with. Since we’re not talking about concrete dust regulations, even a standard shop vac will be a good bet to help contain the mess.
If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  

Different types of table saw rely on different motors. With the smaller and more portable saws, 120V direct drive motors can deliver up to 2HP. This is more than enough power if you’re working with less substantial sheets of material. The larger saws have belt drive motors running on 240V. These produce 3-5HP. Think carefully about the materials you’ll be working with. Get the right sized motor for your cutting needs.
Buying a table saw can cover a lot of bases. You have everything from DIY models to professional production level cabinet table saws. In this article, we’re looking what is arguably the most popular – jobsite table saws. They’re on the less expensive side and are highly portable compared to their shop counterparts. That makes them go-to tools for framers, jobsite carpenters, and Prosumers.
With a cutting speed of at least 4,500 RPM, nothing will hold you back from getting the job done in minutes. Hitachi job site table saw is designed to give you freedom in your work and the ability to manage your time. Keep every minute accountable by investing in the right tools for your workshop. However, during different occasions, you will have different materials both in size and texture. During such moments, you will require adjusting the fence to accommodate your material and cutting style. This job site table saw is designed with an adjustable feature to ensure your precision and accuracy is not compromised. The low power consumption makes it easy for you to maintain the saw and enjoy smooth and accurate results at no extra cost. When it’s not in use, the table saw has fold and roll stand that guarantees you space saving and convenient storage. The foldable design also makes it easy to transport from one place to the other comfortably.
×