We really should point out a big deal here and that’s the SawStop. It’s hard to put a price on safety and while the SawStop costs more than 3 times what the Hitachi costs it does offer safety that no other saw in test can offer. For those that can afford the additional cost that feature alone may tip the scales for you. Regardless of price SawStop came in 5th place for the categories we evaluated.

In layman’s terms, a miter gauge is a device that allows users to set up the angle of the material being cut with a table saw. And while most table saws come with built-in miter gauges, others, well, don’t — which is why the Kreg KMS7102 Table Saw Precision Miter Gauge System is invaluable. Whether you’re replacing an old, worn-out gauge or putting it to use in conjunction with a table saw that didn’t come with its own proprietary gauge, the KMS7102 is specially designed with precision in mind. After all, accuracy is vital to successful woodwork.
The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
As for extensions, I have added the TS1002 and TS1003 outfeeds (rear and left side respectively) – They do a great job supporting the workpieces without making the saw the least bit tippy. For my use, I don’t get much use from the left side support, but the rear outfeed is great. Much nicer than setting up an outfeed stand and trying to dial it in.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.
To avoid such scenario, you can take a moment and check our full reviews out. We offer more than enough insight into the capabilities of particular models we consider are worth checking out. Therefore, if you’re in a dilemma about which table saw to buy; don’t hesitate to refer to this article. The more you know about a certain unit, the fewer problems you’ll have when the moment of purchase comes.

We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.

As for various accessories and attachments such as rip, miter and blade guard, these can be stored in their own specially designed hangars. If you plan on using other blades (and you probably will) there is also a well where you can store all the blades you have. In order to keep the surface of the table dust-free there is a dust collection port featuring a shrouded design which can be attached to the vacuum.


Delta 36-L352 10 in. contractor table saw is a heavy duty table saw. This big guy is no joke! Its 15 A, 3 HP motor is not only powerful but smooth. This Delta table saw also has a HUGE rip capacity of 50-52 in. and a 82 in. table, so there won’t be much this table saw can’t handle. Its integrated BIESEMEYER fence system, precision bevel gauge, and bevel dial work together to help you get highly accurate cuts down to the nearest 1/4 degree and 1/64 in. Now that’s accurate! Other notable features are its bi-level dust extraction system which helps you keep your work space clean, large blade opening, and SURE-LOCK dual front cranks for easy access. This table saw is ideal for the pros.
A 50 rpm deviation at those speeds is approximately 1% variance which is well within the tolerance we should expect from taking the readings at a precise instant of time. The meters were in constant motion and we took the reading off of a single video frame that represented our determination of no-load speeds. We report them as our instruments showed them. 1% is acceptable.

The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
Compared to some of the other miter saws we’ve used – predating the new riving knife requirement, the Bosch GTS1031 guard system is much easier to install and remove when necessary (and to put the saw back into portable mode). We timed ourselves and assembled and tore down the saw in just over 2 minutes – and we were confident that our time would get better with more practice. The table is made of machined cast aluminum and is texture-coated to make it fairly slick – something that really helped when cutting larger pieces of 3/4″ plywood for a workbench surface. As for extending the table – that was super-easy. You just lift the table extension handle upwards and slide the table to the right. This gives you a full 18″ of rip width to the rip fence with your material to the right of the blade. Collapsed, you get up to 10″. Motion of the rip fence and the table extension were smooth. While the fence had some wobble in it at the far end – this completely disappeared when you locked it down – and the shape of the rear of the fence locked it straight every time. It’s a good system and more than adequate for a low-cost portable saw like this. We’ve seen more robust fence systems. But typically the trade-off has been in weight as well as cost.
The Grizzly G0690 is a very unique and powerful table saw and each part of it says performance and quality. With a 3 HP, 220V, 3-phase Leeson motor, heavy cast iron trunnions, wings and table to its triple belt drive system, this model should definitely last you for a lifetime. It’s not only its impressive build quality that’s going to strike you about it, but also its other features that include a four inch dust collection port, a T-slot miter gauge, a magnetic switch, but also heavy cat hand-wheels, riving knife and camlock T-fence. If you’re a professional who’s been using cabinet tablet saws for a quite a while, you’ll immediately appreciate the quality of the Grizzly G0690.
A little unusual for Bosch’s larger tools, it comes in reasonably light weight at 60 pounds – only Skilsaw and Ryobi posted lighter weights. Like Milwaukee in our 18V impact driver shootout, the Bosch 4100 didn’t really stand out from the crowd in features and performance. It’s solid consistency in every area we tested earned it the top spot in the class.

Table saws will continue to be popular and much sought after tools in any workshop or construction site. There are many terrific styles on the market which is why it is important to do some research and look at the reviews provided here as well as the tips contained in this guide to help you choose the right table saw for your needs, whether you are a professional or a DIYer who loves to work in the workshop making things for enjoyment.
I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.
You will need specialty blades for cutting materials such as plywood, masonry, hardwood and metals. Other specialty blades are used for dado cuts. Most dado sets have multiple rows of teeth and chippers and they are typically much wider than traditional blades. Be sure that the model of table saw you have can accommodate the type of specialty blades you want to get so you don’t waste your money on a blade that won’t fit.

From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.
I also added in a bicycle saddle bag, that attaches easily to the tube frame of the saw. In it, I keep my PPE, and my Grr-ripper push blocks (great upgrade over regular push blocks). I also have a push stick made of wood that was modeled after the plastic one mounted on the back of the saw. The wood one is there now. I read too many stories of injuries after the blade touched the plastic stick, which to me is the whole point of using a stick – to avoid injuries. These things turning to shrapnel seems like a bad idea.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
Like the Bosch, this Dewalt comes with a rolling stand. It’s convenient to set up and take down, since you can do it without helpers or tools. It rolls like a dolly, and opens into a nice, sturdy table. We especially like the splayed legs, since they lend the whole thing a bit more stability than the Bosch version. Unlike the Bosch’s stand, the Dewalt’s has semi-pneumatic tires which won’t ever go flat.
One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.

Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.

I definitely give this one 5 stars, but this is specific of the application – it being portable. If I was comparing it with other Hybrid saws, than this one doesn’t really compare when it comes to power. That being said. I was shopping for a table saw, after many years of working with a circular saw, and a straight edge – for me – it was time to get a setup for repetitive cuts that would be easier, and less time consuming (not to mention more precise, as the machine...
Hybrid table saws were produced by many manufacturers as they found there was a gap in the market for a table saw between the contractor saw and the cabinet saw. Contractors wanted something with the power and functionality of a cabinet saw but not necessarily the heavy weight of a cabinet saw. One good other point for the hybrid saws is price, cabinet saws are often very expensive because of the cast iron table tops etc. so a hybrid is a great saw if you’re looking for something slightly cheaper.
Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!

We cannot emphasize enough how important it is to think about safety at all times while using these tools. Even the slightest mistake can make a difference between life and death. The worst part is the fact that it usually happens in an instant, leaving you no time to react at all. Therefore, whatever you do, don’t forget that there’s a thin line between you having ten fingers at one moment and 8 in the next second.

Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.


The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. There is tool-less assembly of the riving knife and anti-kickback pawls. It has a large easy to access ...  More + Product Details Close

The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.
For ideal usage, the on/off switch needs to be mounted on the front of the saw and should be easy to turn off with your knee or a swat without having to look at it to locate it. Most table saw models have a safety feature that is a plastic key that has to be inserted before the table saw can be turned on. Some may even have a way to padlock the switch.
The obvious starting point for an analysis of which saw is best suited to the needs of a given person (or company, school workshop, and so forth) is the budget at hand. Even the most affordable table saws of a quality meriting serious consideration cost more than 200 dollars; such units are small but still capable of many tasks. The top of the line table saws come with price tags topping out at well over 3,000 dollars and can handle almost any lumber you would ever need cut and then some; more often than not these mighty saws are more tool than needed, so to speak.
Safety is a prime concern for Bosch. From the SquareLock Rip Fence through to the patented SmartGuard System to lessen any chance of kickback, your security and comfort is taken care of. The blade guard and riving knife are quick-release. This takes away any excuse for not putting the guard back in place because it would be too much trouble, something that’s an accident waiting to happen.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
It's not really a great choice for professional woodworkers, but for home do-it-yourself users looking for a more than competent contractor saw for their workshop, the Ridgid R4512 is a terrific value. It lacks the SawStop's safety features, but comes in at less than a third of its price. Build quality is first rate, most users say, with a cast iron table that does good job of damping down vibration. Users add that it cuts smoothly and accurately.
Below we’ve included the current pricing (at the time of publishing this article). Pricing includes the cost of the stand and ranges from a low of $349 for the Hitachi to a high of $1,299 for the SawStop. The lowest price isn’t always the best in our opinion, we’re looking for the best value.  The Hitachi is an incredible deal at $349 and our top pick for price and value for a saw that has lots of power, a rack & pinion fence, and a solid stand.

First, consider the types of cuts you’ll need to make, and which types of stock you work with on a regular basis. Think about the largest rip cuts you need to make, and get a cabinet saw with a suitable max capacity for rips. Find the thickest stock you need to cut, and make sure your new machine has a high enough depth capacity to make the cut cleanly. The larger your average stock, the larger a workspace you’ll need on your new cabinet unit. It’s also a good idea to think about bevel and miter cuts which you’ll be making on your table saw. All of our recommendations have the capacity for both, but some come with miter gauges and others don’t.
For those of you who are looking to up your DIY game but don’t have enough capital to make the Dewalt DW745 happen for your home shop, this Craftsman is a decent budget choice. It’s powerful, lightweight, and extremely affordable. We don’t think you should expect too much from this one, though, since it has a very light table and a fence that won’t line up quite as precisely as you’d need for furniture-making or professional-grade projects. It’s cheaply-made, and doesn’t have as user-friendly a design as our other choices. For the home carpenter, though, this should do the trick for all your basic framing cuts.
The Powermatic used to be another all-American classic, much like the Delta. This latest version has the same recognizable yellow finish, on a steel cabinet and cast iron worktop. Unlike most other cabinet units, this one has cast-iron extension wings, which makes them just as sturdy and level as the central worktop. It’s loaded with a 3 HP motor, a 50-inch fence, and all the other basic features that our top three picks have.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
This blade shares many features that come standard on other Diablo blades. The carbide teeth are cut from Diablo’s TiCo High Density Carbide. Perma-Shield non-stick coating helps the blade move through material with less friction, reducing heat that can lead to warping in addition to corrosion. Diablo’s Tri-Metal Shock brazing process ensures the teeth stay in place much longer than other blades and can withstand impacts that leave other blades in need of a dentist.
A table saw can be classified in many ways, and I’ve come across terms like contractor, folding, featherboard, hobby, induction, sliding and zero clearance. However, I will conform to the most basic and clear classification and range the tables accordingly. That means I’ll order them by benchtop table saws, jobsite table saws, cabinet saws and hybrid table saws.
×