The frame is also improved. Instead of the basic roll-cage on the Dewalt, this one neatens things up with an integrated sub-base. It’s a rugged rubber-like pad which serves as a bumper between the main frame and your truck bed or worksite table. Both the table and the sub base are joined to the main frame, and they provide strength at both ends of the design. As with the Dewalt, you can store your tools and accessories inside, an on hooks outside the Bosch.
We spent over 30 hours researching and testing 10 different brands of table saws and found that maximum speed, cord length, and cut depth were most important. The DEWALT DW7480 table saw scored high marks in every category and is our top pick. This 48 pound table saw is perfect for using at home or taking with you to the job site. It has a powerful 15 amp motor and 24” rip capacity that makes it a favorite with everyone. The 2 ½” dust collection port allowed us to connect the saw to a shop vac and reduce the amount of dust that was in the garage.
Setting up both saws was quick and easy, since their factory-adjusted blades and fences were square and parallel to the tables' miter gauge slots out of the box (this is one of the reasons to buy a $350 table saw over a $100 one). Both saws had similar setup procedures: Attach the fence, raise the riving knife, attach anti-kickback pawls and attach the blade guard. There is no on-board stowage space for the DW745's rip fence, but this does not really affect the setup time or effort by much.
Both the riving knife and the blade itself has a quick release design that lets you remove each one in minutes after accessing the arbor lock and without using any special tools either. The blade guard has a similar design that allows you to remove and replace it without any tools. This guard does a good job of keeping your hands and any other body parts safe as you use the saw.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.
It’s expensive. This one will cost you over $3000. That’s no casual purchase, and the high price tag makes this cost-prohibitive for some buyers. However, you really can’t put a price on the peace of mind that comes with having a unit with this sort of safety system onboard. Our advice? If you can muster the cash, and will get your money’s worth out of the machine, it’s well-worth the price.
Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
Among the features that set this table saw apart from other competitors is the SquareLock Rip Fence. It is fabricated out of machined aluminum, slides up and down the rail without a hitch, and fixing positions couldn’t be easier. It’s probably the best fence I’ve seen in portable table saws, it feels very solid and is incredibly accurate and precise.
Clint DeBoer When he's not remodeling part of his house or playing with the latest power tool, Clint enjoys life as a husband, father and avid reader. He has a degree in recording engineering and has been involved in multimedia and/or online publishing in one form or another for the past 21 years. In 2008, Clint was one of the founders of the Pro Tool Reviews online magazine. He hopes his efforts at PTR will provide builders and contractors with reliable and engaging tool reviews to help them make better tool purchasing decisions.
While ordering generic no-name products might be fine for something like breakfast cereal, power tools are different. When you use power tools, your safety is at stake. If you pick up some cheapo piece of mass produced junk just because the price is less than a name brand, you might end up paying a lot higher price for it than you counted on. Why? Because generic power tools are not usually held to the quality control and accuracy as big box brands such as DEWALT and Bosch.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately. 

Make sure you know what’s covered and what’s not, especially if you’ll be using your machine commercially (many warranties are strictly for individual, not commercial use). It’s also a good choice in this case to purchase add-on warranty coverage from a third party at the checkout. We recommend these policies for most portable table saws, since most manufacturers have either very short warranty coverage, or longer warranties which require you to foot the bill for service calls or for returning the machine to the maker.


The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
There are two major points that affect post-calibration table saws: fence quality and overall stability. A fence works by grabbing hold of the table edge and clamping into it. The best fences, like Biesemeyer, have three points of contact. They’re just not where you’d expect. All three are on the front, leaving none on the back. With a wide cast metal front clamping system, the front is pulled flush and self-aligns. It requires a solid locking mechanism to ensure the fence doesn’t move during cuts, but it is very possible.
Due to the position of the motor, dust collection is often an issue with these units, especially in comparison to the cabinet type. However, an industrial vacuum is usually a small and worthy investment which should solve the issue effectively. The main advantage of this type is the fact that it’s much cheaper than its nearest equivalent – the cabinet type.
I’m no stranger to Bosch’s 4100-09 saw with Gravity-Rise™ stand. I’ve used one several times to build projects for this magazine, including the Serving Tray Cart that appeared in the June issue. So, I was not surprised when it tested impressively here. Rip cuts were on the mark, thanks to a rugged, beefy fence that stayed parallel to the blade each time I reset it. A flip of a red lever underneath unlocks the rails so they slide out and extend ripping capacity up to 25″.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
PLEASE EXCUSE THE PICTURE, LUMBER JOCKS REQUIRED ONE. I AM AWAY FROM HOME AND COULDN’t RUN OUT TO THE GARAGE TO SNAP A SHOT. I am writing a review of my Bosch saw after a few months of use. I bought this saw last November after my Ryobi saw up and died during a project. I looked at several saws in the $600-$800 range and narrowed it down to four options. The Bosch and DeWalt jobsite saws, and the Delta and Ridgid contractor saws. My requirements were in a realativly compact saw th...
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
When it comes to power tools, table saws provide convenience when tackling DIY jobs or larger commercial tasks. With their table surface, you are able to get more accurate cuts with the materials you are working with. Utilizing the miter gauge, you will find these power tools to provide the same accuracy as your favorite circular saws without the hassles.

When your skin contacts the blade even slightly, the charge transfers, and a switch flips on the motor, activating an instant brake. The aluminum brake swings into contact with the blade, stopping it instantly. The brake also propels the blade down through the arbor, so it retracts completely below your worktop. That means that other than the initial contact, you won’t touch the sharp edge at all.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More

The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.

You can opt to extend the warranty coverage to 3 years, all through an external provider. We actually prefer these third-party warranties for power tools because they allow you to deal with people who are on your side, as opposed to company representatives, who can be frustrating to say the least. We think add-on coverage is a great safeguard for any cabinet table saw, and it’s a very reasonable proposition on this model.
Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, over sized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
Bosch 10” table saw has it all in terms of precision and accuracy. It has a riving knife system for high material controls and visibility in cutting. The blade is designed with anti-kickback pawls to ensure once you start cutting, you will get accurate results to the end. The entire unit is designed with heavy-duty material for durability. The square lock rip fence has adjustable style to guarantee continued accuracy and precision in all your work. Additionally, the table saw has an easy to transport design with additional tabletops handles for portability. You can also regulate the cutting speed of the table saw to the place you are comfortable.
×