Next, the rip fence is pretty hard to adjust also, and mine had a few thousandths of a bow, but that bow is way within industry standard for a portable saw. Here's what you do: First, check it for parallel, you might get lucky. (On a side note, there is a fine line between how tight to set the locking arm adjustment screw with this rip fence. Too tight, and when you lock it, you'll loose the self-adjustment feature, too loose isn't good either. Adjust the screw (on the rear of the fence), to where the fence self aligns while still getting tight) If you are like me, mine was 15 thousandths out, then unlock the locking handle and loosen the two screws on top closest to you in THIS ORDER! Loosen the screw closest to the lock handle first, and for a few turns. Next, loosen the screw that is about 6 inches away toward the middle just enough to where the fence will rotate on this screw, but not so much as to be sloppy. Begin experimenting. Pivot the fence back and forth, running your measuring device up and down the fence until you get pretty close. Lock handle and checking for parallel. Again and again. When you finally get pretty close to parallel, then lock the lever and experiment with locking both screws. If it doesn't move and you are within a few thousandths, then voila, you are done with adjusting the blade and rip fence for parallel. The other adjustments are straight forward, and once set up, THIS IS A GREAT SAW!!!!!!!!!!!!!! Good luck, hope this review helps
Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.

You can store and transport the Bosch upright or on either of its sides. In between our tests, we found that the saw neatly stored away on its side on a workbench shelf. On the other hand, the DeWalt can only be stored or transported in its upright position. While it may possible to rest the saw briefly on one of its sides, there is the potential to damage the power cord, plug, or the ends of the telescoping fence rails.

Like most other product review sites, ConsumerSearch is supported by a combination of commissions on the sale of the products we recommend and ads that are placed on our site by Google. If you find something you like, you can help support us by clicking through and buying the products we pick. Our editorial process is independent and unbiased; we don’t accept product samples, requests for reviews or product mentions, or direct advertising.

Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.
Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.

We absolutely love the guard on this model. Like the Grizzly, the Jet is equipped with a riving knife or splitter, a blade guard, and kickback awls. The Jet’s our favorite of the two to use, because the whole system is modular: you can take it apart or put it back together without using any tools! The splitter (or riving knife) attaches to the same arbor component as the blade, so no matter how you bevel, and no matter what size blade you use, the splitter always lines up without needing any adjustments.
Strangely, DeWALT provides no power cord wrap. It’s a basic detail the other saws have and this one really needs. The steel “TV tray” type stand sets up fast, and rubber feet hold it firmly in place. When you are done sawing, you’ll have to lift this wheel-less saw to transport it, and there are contoured grips molded into the table edges to make that easier. At more than 50 lbs., though, the saw feels heavy. But the tradeoff for the convenience of wheels is that DeWALT can keep this setup even more compact — probably much appreciated by contractors. The whole works fits in a car trunk.

While we rotated the plate, we recorded the maximum reading on the dial indicator. We validated each maximum reading by running the test for a second time and noting that the readings were consistent. TBB also noted that as we performed these tests on all eight saws, the maximum readings occurred at different parts of the plate along its rotation. Because the max readings were in different and discrete parts of the calibration plate, TBB had a very high level of confidence in the flatness of the calibration plate, itself.
Our table saw review quickly showed that today’s portable table saws are light-years ahead of the small-saw offerings from a decade ago. They feature big-capacity cutting, greatly improved safety features and attached stands for easy setup. And saws in the upper price range rival stationary saws in accuracy and quality of cut. We limited our review to saws that included a stand with wheels and ones that could rip at least 24 in. wide, only the best table saw for our readers!

The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.


The stand is collapsible and wheeled like others, but it’s not the gravity-rise style. You’ll have to use a foot to stabilize it while you pivot it up or lower it down. The lower locks are released with your feet and there’s some question about the long term durability of the releases. An open housing design has two major results – motor cooling should be more efficient but it trades off storage for an extra blade. There’s really way too much to talk about here, so check out our full review of this model.

Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.
The dual extension tables (rear and side) offer 50% more table space than most rectangular units. We also appreciate that Grizzly have put all the space under the worktop to use, with steel-frame shelving built in as standard. You can use it for scrap wood, tools, and accessories: you can even fit a full tool chest under there! It’s a good space-saving touch for busy shops.
If you’re a professional woodworker, you should expect a standard hookup on any saw. However, you’ll find that no portable table saw does a perfect job collecting sawdust. Since these aren’t enclosed tools like a cabinet saw, there are lots of ways for dust to find its way to your floor and spray around your shop. You’ll want to look for the most enclosed, effective design possible, and pair it with a vacuum system that’s got some heft.
Next, the rip fence is pretty hard to adjust also, and mine had a few thousandths of a bow, but that bow is way within industry standard for a portable saw. Here's what you do: First, check it for parallel, you might get lucky. (On a side note, there is a fine line between how tight to set the locking arm adjustment screw with this rip fence. Too tight, and when you lock it, you'll loose the self-adjustment feature, too loose isn't good either. Adjust the screw (on the rear of the fence), to where the fence self aligns while still getting tight) If you are like me, mine was 15 thousandths out, then unlock the locking handle and loosen the two screws on top closest to you in THIS ORDER! Loosen the screw closest to the lock handle first, and for a few turns. Next, loosen the screw that is about 6 inches away toward the middle just enough to where the fence will rotate on this screw, but not so much as to be sloppy. Begin experimenting. Pivot the fence back and forth, running your measuring device up and down the fence until you get pretty close. Lock handle and checking for parallel. Again and again. When you finally get pretty close to parallel, then lock the lever and experiment with locking both screws. If it doesn't move and you are within a few thousandths, then voila, you are done with adjusting the blade and rip fence for parallel. The other adjustments are straight forward, and once set up, THIS IS A GREAT SAW!!!!!!!!!!!!!! Good luck, hope this review helps

For homeowners without the luxury of a huge garage to fit their enormous table saw, DEWALT’s DWE7480 is a compact alternative to bulkier machines with the same wood slicing power. Measuring 25.8" x 26.5" x 13.9", the DWE7480 hosts a 15-amp motor that cuts at an unbelievable 4800 rpm with a ten-inch blade, meaning this small package packs big performance — and with adjustable rear feet that are designed to allow users to level their table saw on uneven surfaces, you’ll be sure to get a clean, precise cut every time, no matter how rugged the terrain. An additional dust port makes collecting your sawdust a breeze — especially if you attach an optional shop vac extension.

Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.
Finally, hybrid saws combine the lighter weight of the contractor saw with the more powerful motor and sturdier construction of the cabinet saw, at a price that’s easier for the occasional woodworker to stomach. They can run about $1,200 or so, and weigh in at under 300 pounds. Their motors are generally in the 1.5 to 1.75 HP range, and can be used with standard 110V outlets.
It’s heavy-duty. Like all great cabinet saws, the Grizzly is built from parts that can last a lifetime or more. It has a cast-iron table, that’s precision-ground to be exactly level, with no warps or imperfections. The trunnion supports holding up the motor are also solid cast iron, which means that they don’t translate much vibration to the work surface at all. The paint on the cabinet and extension frames is powder-coated, and the miter gauge and riving knife are solid steel. Both extension table surfaces are made with a coated, engineered composite, which stands up well against dings or scuffs.

rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces

Some previous buyers had motor trouble. Their units conked out early, or worked inconsistently. Apparently, that was down to cheap internal bearings used in the first few iterations of the Bosch. However, according to company replies to some reviewers who cited the issue, the problem has been addressed in the last few versions of this model. We’ve also found that reviews from the past few years are much more consistently positive.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.

We really should point out a big deal here and that’s the SawStop. It’s hard to put a price on safety and while the SawStop costs more than 3 times what the Hitachi costs it does offer safety that no other saw in test can offer. For those that can afford the additional cost that feature alone may tip the scales for you. Regardless of price SawStop came in 5th place for the categories we evaluated.

The DCS7485T1 60-Volt MAX 8-1/4 in. table saw The DCS7485T1 60-Volt MAX 8-1/4 in. table saw is maximized for accuracy capacity and runtime. The brushless motor delivers the power to cut all common materials the rack and pinion fence allows for fast easy adjustments and provides the capacity to rip 4x8 sheet goods. The DCS7485T1 comes with 1 ...  More + Product Details Close
It’s often overwhelming when looking for new power tools and products online. So many features, specs and brands etc to research and review. So, what should you look for when buying a new table saw? One thing we always mention is to make sure you read as many table saw reviews as you can before purchasing one, this will insure you have the best table saw for your requirements.
The accuracy and safety of any given saw is dependent upon the blade being parallel to the rip fence. Since we tested the amount of difference in parallelism between the saw blade and the miter slot in the previous test, we need only to see if the miter slot is parallel to the rip fence to see if the saw has a parallel relationship between the blade and the rip fence.
Contractor units are the next step up from portable (or jobsite) table saws. A contractor table saw has a worktop and motor assembly that looks a lot like a cabinet model, only it’s missing the cabinet! Contractor units aren’t quite as portable as a job site saw, but they’re about half the weight of a cabinet saw. They pack a lot more power than a portable unit, and their cutaway stands make them fairly manageable for folks who have helpers to assist in getting the saw off the truck and set up at the site.

The Delta 36-L552 is the right cabinet table saw for boat building cabinet making and also woodworking. It features a fifty two inch Biesemeyere fence, speedometer style scales and also dual crank (up-front) controls with locking cams. Taking a closer look at the inside of the Delta 36-L552, we find a powerful 5 HP motor rated at 220V which is perfect for cutting engineered products such as melamine, MDF, but also hardwoods.
But if you have the space for the DeWalt to sit upright at a work station or deep storage shelf, then it may be the better choice, thanks to its more comfortable adjustment controls. You won't be able to use a dado blade with the DeWalt (at least not safely), and the rip capacity is slightly smaller, but there's a reason why it's been popular for a while now. It's a great saw that delivers reliable performance.
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.
Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.

Portable or “jobsite” table saws are the absolute opposite of cabinet models. These are the lightest, most travel-friendly table saws on the market. These are easy to pack up and store in the back of a pickup truck or work van, and they can be set up pretty much anywhere. You can fit them to folding stands, use them on countertops, or sawhorses. We love them for quick contractor jobs, and they’re the ideal tool for general handymen who do a lot of shorter jobs rather than extended carpentry fittings. These are also a great entry-level choice for DIYers who don’t need a massive table saw, but need something that they can pack away at the end of the day. And, of course, they’re the least expensive table saws you can buy!


Home Depot sells around 60 models of table saws on its website, and the top models get hundreds of reviews from users. We found four portable saws with ratings of 4.5 stars or better from 250 users or more, and one contractor saw gets ratings just shy of 4.5 stars overall from more than 650 owners. Individual reviews are fairly short and include ratings for quality and value.
If you want to increase your safety, get a saw that has a flesh sensor. Doing so though will increase the price quite a bit, so only get it if you can afford it or care very much about your safety. A flesh sensor will stop the saw in as little as 0.01s after it comes in contact with your skin. While the blade will be damaged beyond repair, you’ll be safe.Now that you know a bit more about the factors to consider when getting a cabinet table saw, let’s take a better look below at some of the best models you can currently buy.
Dust capture from this saw is pretty bad. I was shocked that a European brand would ignore the dust collection to this extent – at least I was until I discovered that their version of the 4100 does have quite a few more pieces that help pull most of the dust from the airstream. There is a plate that encloses the rear around the vacuum port and a bottom grid that allow airflow to the motor while still shaping the airstream to drive the dust to the vac. I added the plate, but decided against the grid. Instead, I added a sheet of ¼” plywood and put a 4” vacuum port in it that I hook up to my dust collector. I also replaced the blade guard with the European version that has a dust port built in. Minor upgrades, but dust capture has gone from terrible/non-existent to pretty acceptable. Bosch also sell a bag that will capture whatever dust would get tossed out the back of the saw, but that isn’t much, so I consider it a waste. I did buy it, and it works well on other tools, but it is not IMO a must-have for the 4100
To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
The Steel City 35955 also comes with a new table insert system, a seamless table top that offers users a flat surface on which they can work on, but also the Push Stick safety system which prevents injuries to the fingers while using the table saw. Warranty wise, you get 2 years limited warranty, which is enough to give users peace of mind that they’re covered for a long time.

Some of the key factors that every woodworks person will ensure are accurate and will not compromise our performance and quality of the saw. With grizzly G0690 cabinet table saw, you will get all these in one packaging. The table saw has a riving knife that will automatically switch to action following the same blade tilts for better performance. Its made of high quality and heavy duty material to guarantee that it will last a lifetime.
×