The biggest advantage of hybrid saws is the fact that they can be plugged in a regular 110V/220V outlet. Therefore, you don’t need any additional power sources in order to use these units. It quite a relief because you’ll avoid any further investments. These saws are quite easy to use if you know what you are doing. However, if you don’t, remember to read the manual before turning your saw on. It will save you a lot of hassle and also keep you safe.
To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.

Apart from some short reviews, we’ve also covered some other aspects such as safety and proper use of these tools. Make sure you thoroughly read our articles because they could save your life. The tips we offered are well-known among the professionals, but beginners are always susceptible to various risks, especially if they don’t know how to handle these tools properly.

Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.
The Bosch will deliver a whopping big 25” rip, where the DEWALT maxes out at a 16” rip. Again, if you like the other features of the DEWALT better than the Bosch, this larger rip capacity might not sway your buying decision one way or the other. Personally, i would lean towards bosch, but that’s just me.It truly is the best portable table saw on the market today.
Table saws in this best table saw review run the gamut in price and quality. You can buy a table saw for as little as $150, and if you use it just to occasionally rip a board, that may be all the saw you need. If you want a saw that’s easy to carry and you don’t need to rip sheets of plywood in half, look for a “compact” saw like the DeWalt DW745 (shown) or the Bosch GTS1031. If you have room for a little larger saw that’s slightly less portable but capable of wide rips, consider one of the best table saws we review here. And finally, if you want to build cabinets or furniture and have a big enough work area, you can step up to a stationary contractor’s saw like the Ridgid R4512 (shown), for about $650.
You will not always get your job within the workshop, there are moments where you will have to get out and work from a distant place. Therefore, you will require having a table saw that is portable and reliable for such duties. Rockwell table saw with a laser has large legs with wheels. You can easily pull it to any place comfortable as the wheels keep rolling. In other words, you will not have to struggle with the entire unit trying to lift it when you want to switch working positions. Additionally, this table saw has a foldable fence for convenient storage and also ensures there is enough room for all size material. The inclusive laser guide is to ensure you get consistency in accuracy. Once the blade is not in the position, the laser guide adjusts automatically for the benefit of the user.
Strangely, DeWALT provides no power cord wrap. It’s a basic detail the other saws have and this one really needs. The steel “TV tray” type stand sets up fast, and rubber feet hold it firmly in place. When you are done sawing, you’ll have to lift this wheel-less saw to transport it, and there are contoured grips molded into the table edges to make that easier. At more than 50 lbs., though, the saw feels heavy. But the tradeoff for the convenience of wheels is that DeWALT can keep this setup even more compact — probably much appreciated by contractors. The whole works fits in a car trunk.
Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.

Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.
One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.
Reviewers recommend these models for easy transport to jobsites and for easy storage in a small workshop. Portable table saws come in two types. Benchtop saws sit on top of a workbench and are light enough to pick up and carry; jobsite saws are mounted on folding stands, usually with wheels for easier transport. The main drawbacks of a portable saw are its lower power and smaller table, which makes it tricky to cut larger lumber and sheet material such as plywood. Prices for portable saws start at less than $200, but the best-rated models typically cost $300 or more.
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.
It’s often overwhelming when looking for new power tools and products online. So many features, specs and brands etc to research and review. So, what should you look for when buying a new table saw? One thing we always mention is to make sure you read as many table saw reviews as you can before purchasing one, this will insure you have the best table saw for your requirements.

Make sure you know what’s covered and what’s not, especially if you’ll be using your machine commercially (many warranties are strictly for individual, not commercial use). It’s also a good choice in this case to purchase add-on warranty coverage from a third party at the checkout. We recommend these policies for most portable table saws, since most manufacturers have either very short warranty coverage, or longer warranties which require you to foot the bill for service calls or for returning the machine to the maker.


What 🤔?? I find it pretty rare to have to re-align the rack and pinion fence on the dewalt, but short of the first time figuring it out, it shouldn’t take more than 5-10 minutes to do. The time savings comes in not having to stick a tape to the fence every time you move it to ensure it’s parallel. I am excited to see other tool manufacturers are using rack and pinion fences now so that there are other options besides the dewalt, namely skil’s latest worm drive ts and the latest hitachi, I’m just not interested in any other fence system on a job site table saw.
The Bosch is, in fact, almost twice as heavy its competitor. Despite its aluminum try! But…..there may be other things to consider when you think about the portability of a worksite table saw. One consideration is the ease of setting up and moving the saw table. The Bosch, with its unique Gravity-Rise Stand and solid rubber wheels, may be heavier but easier to move and set up for use. The DEWALT wouldn’t require as much muscle to move, but the table is relatively small and it has no wheels. It bears mentioning that its table is sold separately, and is assembled separately, whereas the Bosch unit’s Gravity-Rise Stand is a part of the overall unit. The stand allows the saw to be raised into working position in a single, fluid movement, and easily cuts set up time in half.
As mentioned, the look is similar to a hybrid with a full enclosure. Looks can be deceptive, though… The core design purpose is for this saw to stand up to constant heavy use in a commercial setting. This is not a tool you buy for casual woodworking at home.These bulky, heavy units are built to last the distance. They can weigh up to 500 pounds. You’ll get an accuracy and rigidity not available in lesser types of table saw.Other table saws call for regular adjustments. With a cabinet saw, you won’t need to do this as often once it’s set up properly. 240V motors developing 3-5HP mean there’s very little the best cabinet table saw won’t rip through with ease. Large sheets of hardwood are no problem at all.

Portable or “jobsite” table saws are the absolute opposite of cabinet models. These are the lightest, most travel-friendly table saws on the market. These are easy to pack up and store in the back of a pickup truck or work van, and they can be set up pretty much anywhere. You can fit them to folding stands, use them on countertops, or sawhorses. We love them for quick contractor jobs, and they’re the ideal tool for general handymen who do a lot of shorter jobs rather than extended carpentry fittings. These are also a great entry-level choice for DIYers who don’t need a massive table saw, but need something that they can pack away at the end of the day. And, of course, they’re the least expensive table saws you can buy!


If you’re a professional looking for a great table saw for the worksite, you’ll love the features and performance of the DEWALT DWE7480. Equipped with the Site-Pro Modular Guarding System has a rack and pinion telescoping fence rail that will allow you to make fast, smooth and accurate adjustments. This is the perfect table saw for cutting larger shelving and trim easily. With a 15 AMP 4800 rpm motor, you will go through all types of wood, even hardwood, with ease.
While it’s bargain-priced, it has very impressive cast iron and steel construction, with all the same essential features as our other top table saw recommendations. On the downside, it’s the slowest of the three in terms of blade speed, and it has the shortest warranty coverage. This one also lacks some of the sophisticated safety features and creature comforts of our more expensive recommendations.
The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).
The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.
×