We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.
No matter the model or price, a table saw should cut a range of material thicknesses and hold its settings accurately. So, after installing a new Freud hi-ATB thin-kerf blade in each saw, I made repeated rip cuts on MDF, resetting the fence each time to check for consistently thick offcuts. After that, I raised the blade for more rip cuts on heavy, long planks of 2 x 12 Southern yellow pine, before tipping the blade to bevel-rip 2″-thick poplar. Then I switched to a 6″ CMT dado set and made a long dado cut in MDF, so I could check for consistent cutting depth — a sign that the undercarriage is stout enough to handle a heavy blade like this. Overall, my test criteria was stability of the stand, cutting accuracy, reasonable dust collection efficiency and all-around convenience of use. Results ranged from exceptional to mediocre, as you’ll see.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.
The biggest advantage of hybrid saws is the fact that they can be plugged in a regular 110V/220V outlet. Therefore, you don’t need any additional power sources in order to use these units. It quite a relief because you’ll avoid any further investments. These saws are quite easy to use if you know what you are doing. However, if you don’t, remember to read the manual before turning your saw on. It will save you a lot of hassle and also keep you safe.

For centuries, the job of the sawyer was, quite simply, to saw logs into lumber. Working in two-man teams, a pair of sawyers would use massive saws -- called whipsaws or pitsaws -- to cut felled trees into workable planks with their own muscles as the motive power. The job was exhausting and often dangerous, yet necessary to create the precious lumber used to build everything from homes to railroad bridges.

I bought this saw to add to my home shop and a radial arm saw I have had for years. I have owned it since 2009. I bought it after reading reviews in woodworking magazines on line. I did buy the left extension, which I use frequently. This saw has been used for multiple projects, including building furniture, cabinets, cabinet doors and a host of other projects for home, family and friends. It has never let me down, working flawlessly. It has never been out of square. And, yes, I do check squareness every time I use it. Cuts are accurate and the table large enough to manage most jobs without adding an extension. The metal construction is particularly appreciated. The blade is easy to replace, the controls and storage on the unit convenient. What I particularly have enjoyed is the portability and the ease of use of the gravity-rise stand. Being able to move tools around and re-arrange my limited workspace to match the job is important to me. I have read the caveats posted by a number of reviewers, but, in truth, those have simply not been my experience. At 71 with a lifetime of using and buying tools and enjoy woodworking, I count this tool as among one of my better purchases.

If you're currently looking for a cabinet table saw and it's the first time you actually need to buy one, then you should know that they come in a wide range of types, from the larger contractor saws to the portable table saws that most people seem to own. However, buying the right model for you depends on your needs and how you're going to use it.
One drawback is because of the way the blade is stopped, you will want to have an extra blade brake on hand because once it’s used, it cannot be reused. So, if you don’t have another handy, you will have some downtime. Also, the stopping of a blade moving at thousands of RPM can understandably be very hard on the blade itself. Often, the blade may need to be replaced after it has been stopped in this way. Still better than losing a thumb.
Home Depot sells around 60 models of table saws on its website, and the top models get hundreds of reviews from users. We found four portable saws with ratings of 4.5 stars or better from 250 users or more, and one contractor saw gets ratings just shy of 4.5 stars overall from more than 650 owners. Individual reviews are fairly short and include ratings for quality and value.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
I’m trying to replace some lost tools for a doctor inflicted, lawyer cowardice sustained injury. I’ve been a woodworker for more years than I might imagine I am comfortable with saying simply for it seems to have been bestowed upon me from birth. The only comment I have is a general comment. As I’ve noticed from about 20 years ago being introduced do officially being educated at a local community college, everyone there had prestige rights attached to it, a couple of cabinet makers I worked for did also that Porter Cable was the Cadilac of woodworking tools. Well, China… Read more »
The DEWALT DW745 and the Bosch 4100 both have 15 amp motors, so power shouldn’t be a problem with either of these job site table saws. The DEWALT has a high torque motor that is capable of delivering a no-load speed of up to 3,850 rpm. The Bosch 15 amps and a no-load speed of up to 3,650 rpm. The difference between the two is not something that would be noticeable without sophisticated equipment, and will not affect performance in any significant manner. The noticeable difference between the two is that the Bosch 4100 comes equipped with a soft start motor that is lacking on the DEWALT DW745. This will cause a noticeable load on your power source, and may affect other tools and lighting attached to the same source during startup.
While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.
In other words, a malfunction might mean an injury. This distinction could not be more pronounced in any other job site equipment than a table saw. I have personally witnessed devastating injuries on a number of occasions that could have easily been avoided by the use of safety equipment that comes standard on most brand name saws. Liability for a job site injury can be a serious setback for well established companies, but for small, independent contractors it could mean the difference between business and bankruptcy.
It’s also a great table saw in its own right. This one has a wide, cast-aluminum worktable, and an out-feed extension thrown in as well. It has a 4 HP motor which cranks out lots of power, and it’s balanced by a soft start and automatic speed control like on the Bosch in our Top Three. It has wide rip and bevel capacities, plenty of alignment adjustments, and a robust build. Plus, it comes with a gravity-assist wheeled stand thrown in as well.
That’s one major safety hazard which you can completely eliminate with one simple feature. In addition to the magnetic switch, be sure to look for thermal overload protection on the motor. You shouldn’t have any problems with burnout on motors this powerful, but it’s an important safety feature to have just in case, especially for folks who work with thicker hardwood stock. Thermal overload protection shuts the motor off automatically if it’s getting dangerously bogged down.

It’s heavy-duty. Like all great cabinet saws, the Grizzly is built from parts that can last a lifetime or more. It has a cast-iron table, that’s precision-ground to be exactly level, with no warps or imperfections. The trunnion supports holding up the motor are also solid cast iron, which means that they don’t translate much vibration to the work surface at all. The paint on the cabinet and extension frames is powder-coated, and the miter gauge and riving knife are solid steel. Both extension table surfaces are made with a coated, engineered composite, which stands up well against dings or scuffs.


Hello, Thank you for your comment. We apologize for any issues our Top Table Saws of 2018 blog post has caused. It was not written to be a comparative review of the different saws but a list of the top saws that we are currently selling. It would be unfair to compare performance of a portable jobsite table saw to a industrial cabinet saw and then also compare them on price. If you would like to read a very good comparative post we suggest you check out ProToolReviews.com. They are not tied to any manufacturers and have a very unbiased opinion.
When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.
The bench table saw is the least expensive of the four types of saws. Some models come with a folding stand that is on wheels which makes it very easy to move or reposition without having to lift it all the time. Even though it is relatively light, constant lifting can become tiresome. You can mount these on your workbench which will give it more stability and could possibly reduce the amount of vibration as well. These smaller table saws generally have a 1 hp motor or even smaller and can run on a normal household circuit with no issues.

Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.


Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.
home,page-template,page-template-full_width,page-template-full_width-php,page,page-id-4,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on, vertical_menu_background_opacity,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.

Obviously, given its size, the TruePower 01-0819 isn’t the kind of table saw you’d spring for to take on larger projects that require greater motor power — after all, it’s by no means revolutionary in the torque department. But for those who work with smaller materials or softer wood, the Gino Development TruePower 01-0819 Mini Electric Table Saw is a worthwhile, no-frills buy that’s easy on the wallet and can fit in virtually any space with plenty of room to spare.


When you’re setting up your table saw fence, slide it into position by pressing the front of the fence forward against the table with both hands. This will allow the entire fence to slide square to the table. Hold your final position with one hand while locking it down with the other. This should help you avoid many of the accuracy issues that come from an off-square fence.
These smaller table saws, which come in a compact benchtop setup rather than with legs like a traditional table saw, are designed as portable job site saws. But they work just as well in a home workshop, and are ideal for shops that are tight on space. The Bosch and the DeWalt have many of their specs in common: Both include a 15 Amp motor, 10-inch blade, 3 1/8-inch depth of cut when the blade is set at 90 degrees and 2.2-inch depth of cut at 45 degrees. And safety features on both saws include a riving knife, anti-kickback pawls, blade guard and an included push stick. Features The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).
With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.

We made a few test cuts with ¾-inch plywood just to get a feel of the motors we were working with. It became clear pretty quickly that not all 15 amp motors are equal. Once we knew what to expect, we moved to pressure treated 2x pine material in 7-1/2 foot lengths. Why 7-1/2? Our test material started at 15 feet and it seemed silly to have some at 8 feet and others at 6.
I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.
Buying a table saw can cover a lot of bases. You have everything from DIY models to professional production level cabinet table saws. In this article, we’re looking what is arguably the most popular – jobsite table saws. They’re on the less expensive side and are highly portable compared to their shop counterparts. That makes them go-to tools for framers, jobsite carpenters, and Prosumers.
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
×