For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.
One drawback is because of the way the blade is stopped, you will want to have an extra blade brake on hand because once it’s used, it cannot be reused. So, if you don’t have another handy, you will have some downtime. Also, the stopping of a blade moving at thousands of RPM can understandably be very hard on the blade itself. Often, the blade may need to be replaced after it has been stopped in this way. Still better than losing a thumb.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.
The DEWALT Table Saw is designed with a The DEWALT Table Saw is designed with a 15 Amp 4800 RPM motor that quickly rips through hardwoods with ease. With 24-1/2 in. of rip capacity this saw easily cuts a variety of larger shelving and trim materials. Rack and pinion telescoping fence rails make fence adjustments fast smooth and ... More + Product Details Close
A table saw is the centerpiece of any home workshop, and it’s often the very first power tool to be cranked up at the start of any woodworking task. They’re essential for the necessary task of sizing wood for each project – whether narrowing the width of boards, cutting plywood sheets, or tackling specialized cuts like grooves, slots, and tenons. Because of their important role in DIY and professional construction, choosing the right table saw is critically important. At BestReviews, we’ve researched table saws in depth. We’re here to help you decide which type of table saw will best meet your needs.
Look for a blade guard and splitter assembly. The guard will keep your fingers and sleeves away from the blade, while the splitter will keep your wood from re-binding together and jamming the blade, or causing kickback. Kickback is one of the biggest hazards of using a table saw, aside from coming in contact with the blade. Make sure you have either a splitter assembly or a riving knife on any cabinet saw you use.
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
DeWALT DWE7480 is an excellent table saw, especially if you consider its price. It’s a step up from the highly popular DW745 and slightly more expensive, but I think the larger rip capacity and higher RPM are well worth the extra money. The DWE7480 is still in the lower price region though, and unlike the DW745 you can also get this one with a stand: the DWE7480XA!
Home Depot sells around 60 models of table saws on its website, and the top models get hundreds of reviews from users. We found four portable saws with ratings of 4.5 stars or better from 250 users or more, and one contractor saw gets ratings just shy of 4.5 stars overall from more than 650 owners. Individual reviews are fairly short and include ratings for quality and value.