Bosch engineers deserve kudos for the Gravity-Rise stand, and it’s a design some other manufacturers should emulate. Twist one lever, and the sturdy, steel frame folds up or down fluidly to convert from sawing to transport or storage. Eight-inch wheels and lugged rubber tires make this base easy to steer overland or pull up steps. Plus, the base’s stance is wide, giving it sure footing if you are pushing long planks or heavy sheet goods through. It will not tip. But, the stand when erected sets the saw’s tabletop quite high, at 38-1⁄2″. Shorter users may find this to be a bit too tall for comfort.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners. 

Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
Today's table saws also include riving knives, which ride up and down with the blade when its height is changed, rather than splitters that are fixed in place. The problem with the old splitters was that they had to be removed for certain types of cuts, and users might forget to put them back on before making rip cuts. This increased the risk of kickback injuries, which occur when the spinning blade kicks back a piece of wood toward the user with tremendous force, causing serious injury to any part of the body that's hit.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
This woodworking website has tons of information about how to use a table saw: choosing blades, cutting joints, safety features, and more. However, we found only five actual product reviews, none more recent than 2013. Although these individual reviews are hands-on, they don't put saws through any specific, detailed tests. There's also no direct comparison between saws and no formal rating system.
Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.
When it comes to power tools, table saws provide convenience when tackling DIY jobs or larger commercial tasks. With their table surface, you are able to get more accurate cuts with the materials you are working with. Utilizing the miter gauge, you will find these power tools to provide the same accuracy as your favorite circular saws without the hassles.

I just purchased this saw last week. It took several hours to assemble. everything was there and I had no problems putting it together. Not hard but time consuming. The first job was to rework some vertical drawers. It did a good job fence worked great as did the riving knife. Saw was quitter than I expected. overall I am very happy. The only problem was that I had to weight a couple of extra days for delivery due to all parts not arriving at the same time.

For ideal usage, the on/off switch needs to be mounted on the front of the saw and should be easy to turn off with your knee or a swat without having to look at it to locate it. Most table saw models have a safety feature that is a plastic key that has to be inserted before the table saw can be turned on. Some may even have a way to padlock the switch.
Portable saws are usually light and smaller than the other types. The three basic types of portable saws are compact, bench top, and jobsite saws. Because they are designed for portability, the materials of which they are made sometimes lack sturdiness and stability. However, that’s not a reason to be alarmed; a vast majority of these units are absolutely safe for work.

Hybrid models vary widely, so there aren’t any strict pros and cons that apply to all models. They’re generally quite powerful, and you can find them in both 110V and 220V configurations. They’re easy to install on wheeled bases, and work well in both stationary or mobile setups. However, these tend to be quite heavy, and they take up more space than other portable options. They’re a good compromise for ardent DIYers who dream of a cabinet model, but don’t quite have the money or the permanent shop space.
Portable saws are usually light and smaller than the other types. The three basic types of portable saws are compact, bench top, and jobsite saws. Because they are designed for portability, the materials of which they are made sometimes lack sturdiness and stability. However, that’s not a reason to be alarmed; a vast majority of these units are absolutely safe for work.
Ridgid’s fence is outstanding for its design. Its large front plate helps stabilize it and the whole thing just feels solid. There’s very little play compared to some of the others and we were consistently able to lock it down perfectly square. We like the pinion style bevel adjustment. It’s not quite a good as a separate adjustment wheel, but a great improvement over simple sliding. We also like the independent locks for both height and bevel. It’s not often that a height lock would be required, but there’s an element of confidence that comes from knowing it won’t be going anywhere.
For carpentry projects or as a starter saw, the DeWalt DW745 receives solid reviews. Though it doesn't have the capacity of the Bosch, owners say it's well made and easy to adjust. The rack-and-pinion fence earns kudos for accuracy. The saw weighs just 45 pounds and can even be hung on a workshop wall for storage; an optional is also available. The three-year warranty is another plus.
With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.
We’ve used $2,000 as our minimum spending threshold on these models, because that’s what we’ve found you have to pay for a cabinet model with all the features we consider essential: a precision-machined cast-iron worktop, a versatile fence on sliding tracks, a 3 HP motor with belt drive, an all-steel cabinet, a cast-iron trunnion support, and machined flywheels to adjust the blade settings.
A gauge will allow you to make very detailed cross and angled cuts. This is a bit of kit that you need to research in great depth as it can make or break the accuracy of your cuts and angles. With a good gauge, you can check blade height, blade angles, miter angles and much more. For further reading checkout Wikipedia’s table saw page and for in-depth air compressor reviews.
DIY-ers love this type due to its simplistic yet effective operation. However, it’s not unusual for professionals to invest in these in order to avoid investing in cabinet models and save some money. Speaking of money, you should prepare yourself for a hefty investment if you opt for this particular type. However, most models are well-worth the money. These things last for years and don’t require a lot of maintenance apart from occasional blade replacements and minor adjustments.  They are not as easy to use as portable models, but you’ll learn how to use them in a matter of hours or days, as long as you follow the rules written in the user manual.

The DeWalt DWE7499GD table saw earns a third place finish in the safety category thanks to their GuardDetect technology. This doesn’t prevent you from using the saw without the pawls and blade guard in place, but it does require you to physically indicate you are aware they’re not in place. Ideally, this gives your mind one last opportunity to consciously note the additional care that needs to take place before cutting.
For those of you who are looking to up your DIY game but don’t have enough capital to make the Dewalt DW745 happen for your home shop, this Craftsman is a decent budget choice. It’s powerful, lightweight, and extremely affordable. We don’t think you should expect too much from this one, though, since it has a very light table and a fence that won’t line up quite as precisely as you’d need for furniture-making or professional-grade projects. It’s cheaply-made, and doesn’t have as user-friendly a design as our other choices. For the home carpenter, though, this should do the trick for all your basic framing cuts.
You can store and transport the Bosch upright or on either of its sides. In between our tests, we found that the saw neatly stored away on its side on a workbench shelf. On the other hand, the DeWalt can only be stored or transported in its upright position. While it may possible to rest the saw briefly on one of its sides, there is the potential to damage the power cord, plug, or the ends of the telescoping fence rails.
The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
Once again our team has put some serious time and effort into our Head-to-Head evaluation to bring you the most comprehensive information available. For this evaluation, we broke things into several categories including: Precision & Accuracy, Performance (power), Price, and Ergonomics. For each of these categories we’ll rank the saws and at the end we’ll name the Best Portable Jobsite Table Saw based on all the results combined.
It also has the highest blade speed. This model has a similar 15-amp motor to our other recommendations, but it’s geared for maximum efficiency. The result is a blade speed that’s nearly 1000 RPM better than the Bosch or the smaller Dewalt. Reviewers marveled at how powerful this one was compared to the size of the motor, which seems underwhelming from the outside. It rips right through oak, cherry, and other planks with no lag or burnout. In fact, we’re hard-pressed to find something this would struggle to cut, provided you equip it with the proper blade.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
Unlike a lot of competing models, this one is updated regularly. Previous buyers appreciated the thoughtful tweaks, which made it clear that Dewalt listened to feedback from folks who used the first versions. Recent buyers noted the improved rack and pinion teeth, which help the fence lock into position with less play. They also appreciated the reinforced rails, which felt a lot less flimsy than the old version.
When you are woodworking, dust and debris can be a serious bugbear. There’s good news with the DeWalt, though. Connect the DWE7491RS to your favorite vacuum and keep your workspace blissfully free of fine particles. The 2 ½-inch dust port at the rear and 1 ½-inch port off the top of your blade makes for a powerful combination getting rid of dust from above and below.

I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
Often called benchtop, jobsite, or worksite saws, portable table saws are typically made of lightweight materials, such as an aluminum table top, so that they’re easy to move from place to place. Sometimes they’ll have wheels attached to make shifting them around even easier. The motors on portable saws are also much smaller than on other types of table saws, and are typically less powerful.
And finally, they all include a blade guard that can be removed and reinstalled without tools. Because a few sawing operations, such as non-through cuts, require you to remove the blade guard, we like saws that make this task easy. The Bosch, DeWalt and Ridgid saws have well-designed blade guards that are easy to remove and reinstall. The blade guards on all but the Porter-Cable and Craftsman also have a feature that holds the blade guard in the raised position to allow better blade visibility for setting up cuts.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.

On the downside, Delta have changed things up over the past few years, and the news isn’t all good. The motor is still made in the USA, but the frame and structure of the saw is all imported. Recent buyers have reported shoddy quality control and very poor customer service since the company was taken over. Even though the Unisaw still gets great professional reviews, buyers’ experiences are so mixed that we’re not comfortable recommending this one as one of our top picks.
Before you decide to invest in a unit, you must first know what to look for in order to find the best table saw. Many people think buying a table saw is a piece of cake, but the reality is completely different. There are a few things you should think about before buying one, especially if you don’t have any previous experience. Take a moment and read this article, it will help you a lot.
The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.
Table saw flesh sensors are a brilliant and clever piece of engineering. Sawstop revolutionised the industry when they came up with this technology. Human skin is a good conductor of electricity where is wood isn’t. So, the system works by passing an electric current through the table saw blade its self and when it’s cutting wood it’s fine as there is no conductivity between the wood and the blade but as soon as it hits human skin and becomes conductive it triggers an electric brake that stops in the blade in only 0.02 seconds. You may end up with a small cut but at least you won’t lose your finger or worse. There are quite a few different versions now on the market so we would advise you to read plenty of table saw reviews and do you research into the different systems to find the best one for you.

Last but not least, you need to pay attention to the dust collecting capabilities of a particular model. Portable units usually have a weak dust-collecting capacity, but they aren’t foreseen for large projects. However, all other types do feature some kind of dust collecting system. The first thing you should check is the diameter of the dust port. The larger it is, the less debris you’ll have flying around. Also, check out the vacuum requirements because some models work only with super-expensive vacuums. As you can assume, the thing that’s lacking with those models is cost efficiency. However, if you don’t have budget limitations, feel free to invest in a high-end vacuum, it makes a huge difference.

Strangely, DeWALT provides no power cord wrap. It’s a basic detail the other saws have and this one really needs. The steel “TV tray” type stand sets up fast, and rubber feet hold it firmly in place. When you are done sawing, you’ll have to lift this wheel-less saw to transport it, and there are contoured grips molded into the table edges to make that easier. At more than 50 lbs., though, the saw feels heavy. But the tradeoff for the convenience of wheels is that DeWALT can keep this setup even more compact — probably much appreciated by contractors. The whole works fits in a car trunk.
Even a newbie can go around the table saw section at the local home improvement store and feel that some saws have easier adjustments than others. Some are simply easier while others are downright innovative in various ways. Porter-Cable came out of the value group for the overall win with adjustments that are both smooth and intuitive. Dual adjustment wheels mean that you’ll be able to accurately adjust your blade height and your bevel angle—a feature no other saw in this group has.

We absolutely love the guard on this model. Like the Grizzly, the Jet is equipped with a riving knife or splitter, a blade guard, and kickback awls. The Jet’s our favorite of the two to use, because the whole system is modular: you can take it apart or put it back together without using any tools! The splitter (or riving knife) attaches to the same arbor component as the blade, so no matter how you bevel, and no matter what size blade you use, the splitter always lines up without needing any adjustments.


The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.
Service can be expensive on these models, so you should see if the company will be covering repairs, of if you’ll be expected to foot the bill. Add-on plans are a great way to minimize your liability if something goes wrong. By purchasing a third-party warranty, you can have a much better customer service experience. The warranty provider will deal with the company for you, so you don’t have to negotiate or deal with frustrating runarounds.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
Measuring in at 19.9" x 23.4" x 13.4", the SPT70WT-01 is compact enough to fit into any aspiring handyman’s garage, but powerful enough to tackle anything you throw at it on the job site, meaning it’s an ideal entry-level table saw for the amateur hoping to turn his hobby into a career. Sturdiness, durability, and anti-kickback technology make the world’s first worm drive table saw a revolutionary machine. Satisfied buyers can’t get enough of this balanced wood-devouring behemoth.
Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.
It’s just as powerful as our other recommendations. The SawStop has a 3HP belt-driven motor, and like the Jet, it uses a tweaked multi-belt drive system to transfer maximum power from the drive shaft to the blade. That makes for as powerful a cabinet saw as any on the market. This one slices smoothly through anything you can feed into it. It also has a slightly thicker max cutting depth than our other recommendations, so it’s the better choice for sturdy stock.
At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.
This blade shares many features that come standard on other Diablo blades. The carbide teeth are cut from Diablo’s TiCo High Density Carbide. Perma-Shield non-stick coating helps the blade move through material with less friction, reducing heat that can lead to warping in addition to corrosion. Diablo’s Tri-Metal Shock brazing process ensures the teeth stay in place much longer than other blades and can withstand impacts that leave other blades in need of a dentist.
More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.
The Bosch 4100-09 offers many advanced features, making it a very capable table saw for woodworking. The air-filled wheels and gravity rising stand makes this table saw functional and lightweight. Set up and tear down of the table saw is a breeze. This technology allows the table saw to be moved from place to place, even over the most rough and challenging areas of the work site. The 4100-09 weighs 39 pounds, making it the perfect portable table saw. Although it is lightweight, it is very durable and stable.
One of the lightest and most compact table saws was also the most stable: Skilsaw. There’s no wheel base to the stand and the outward angled legs provide a wider platform than it may appear against its colleagues. In second place was DeWalt, also offering a wide platform, but without the amount of rigidity that Skilsaw has in their stand. Coming up in third was Bosch with its gravity rise stand followed closely by Ridgid. It’s important to note that none of the professional class table saws had any stability issues inherent to their extension locking—it was all in the stand.
According to the many reviews posted online, the JET 708675PK is an excellent table saw that features a finely ground and large cast iron table that measures twenty nine by forty two inches and provides plenty of work surface for even the most demanding projects. Also, taking a closer look at the front of the blade, you’ll notice it includes ten inches of clear table which is certainly going to be appreciated by a lot of users. Looking under the table, you’ll notice a wide stance, heavy duty cast iron trunnion mechanism which provides the remarkable performance, almost vibration free operation and incredible stability the JET 708675PK is known for.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More

If you want to increase your safety, get a saw that has a flesh sensor. Doing so though will increase the price quite a bit, so only get it if you can afford it or care very much about your safety. A flesh sensor will stop the saw in as little as 0.01s after it comes in contact with your skin. While the blade will be damaged beyond repair, you’ll be safe.Now that you know a bit more about the factors to consider when getting a cabinet table saw, let’s take a better look below at some of the best models you can currently buy.

rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces


Jet has a strong reputation for providing customers with durable power tools that operate just like professional models but cost less, and that is definitely true of this 10-inch table saw that comes with a riving knife. You’ll like the basic design of this model, which has an intuitive design that allows you to set it up and start cutting faster. It features both a solid cabinet as well as an extension table that stretches out from one end.
One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
If you want to increase your safety, get a saw that has a flesh sensor. Doing so though will increase the price quite a bit, so only get it if you can afford it or care very much about your safety. A flesh sensor will stop the saw in as little as 0.01s after it comes in contact with your skin. While the blade will be damaged beyond repair, you’ll be safe.Now that you know a bit more about the factors to consider when getting a cabinet table saw, let’s take a better look below at some of the best models you can currently buy.

While we rotated the plate, we recorded the maximum reading on the dial indicator. We validated each maximum reading by running the test for a second time and noting that the readings were consistent. TBB also noted that as we performed these tests on all eight saws, the maximum readings occurred at different parts of the plate along its rotation. Because the max readings were in different and discrete parts of the calibration plate, TBB had a very high level of confidence in the flatness of the calibration plate, itself.
rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces
In layman’s terms, a miter gauge is a device that allows users to set up the angle of the material being cut with a table saw. And while most table saws come with built-in miter gauges, others, well, don’t — which is why the Kreg KMS7102 Table Saw Precision Miter Gauge System is invaluable. Whether you’re replacing an old, worn-out gauge or putting it to use in conjunction with a table saw that didn’t come with its own proprietary gauge, the KMS7102 is specially designed with precision in mind. After all, accuracy is vital to successful woodwork.

home,page-template,page-template-full_width,page-template-full_width-php,page,page-id-4,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on, vertical_menu_background_opacity,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
×