Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.
One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.
Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
The Grizzly, like the other cabinet models you’ll see here, requires a 220V power supply. If you’re a professional woodworker, you probably already have a 220V hookup. If you’re a home woodworker or DIYer, you’ll need to have one installed, if you haven’t already. It can be an expensive installation, so factor in the cost when you consider how much you’ll spend on your new saw.

The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.
We spent 42 hours on research, videography, and editing, to review the top options for this wiki. Regardless of whether you're a construction professional, a precision woodworker, or a DIY hobbyist tackling your next home-based shelving project, one of these handy table saws will help you get the job done fast. Our selections include models with durable cabinets, powerful motors, integrated fence rails, and even patented safety systems to protect you from on-the-job injuries. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best table saw on Amazon.
Table saws will continue to be popular and much sought after tools in any workshop or construction site. There are many terrific styles on the market which is why it is important to do some research and look at the reviews provided here as well as the tips contained in this guide to help you choose the right table saw for your needs, whether you are a professional or a DIYer who loves to work in the workshop making things for enjoyment.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.

In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
The DeWalt DWE7480 is a 10 in. compact job site table saw powered by a powerful 15 A motor that has top speeds of up to 4,800 RPM. When this power is paired with its 24 in. rip capacity and 47 degree bevel, this table saw is able to power through even the hardest woods with great accuracy, so you can use it for projects ranging from shelving to trim to hardwood flooring. And despite all its power, this table saw is a lightweight at only 48 lbs. No matter what woodworking project you have in front of you, this DeWalt table saw is able to power through it!

The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
Due to the position of the motor, dust collection is often an issue with these units, especially in comparison to the cabinet type. However, an industrial vacuum is usually a small and worthy investment which should solve the issue effectively. The main advantage of this type is the fact that it’s much cheaper than its nearest equivalent – the cabinet type.

TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.

While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.


Three professional carpenters test ten portable table saws, including two now discontinued. They outfit them all with Diablo 40-tooth general-purpose blades and test them on both 3/4-inch plywood and pressure-treated 2x pine. Each saw earns points for safety features, fence quality, stability, weight, stand design, ease of adjustment, cutting power, and dust collection. Totaling up these scores determines the saws' overall ranking, as well as their "class ranking" against comparably priced brands. Some additional single product reviews of table saws can be found elsewhere on the site as well.
The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.
The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a tool-less assembly of the riving knife and anti-kickback pawls. There is a large easy to ...  More + Product Details Close
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
If you want to take the saw with you and use it in a different location, you can purchase the optional MB-PCS-000 integrated mobile base which features 2 stationary casters and 2 pivoting casters. Furthermore, it’s also possible to upgrade the mobile base assembly to a one thousand pound lift capacity, add a hydraulic piston lift and 4 independent pivoting casters.

If you want to increase your safety, get a saw that has a flesh sensor. Doing so though will increase the price quite a bit, so only get it if you can afford it or care very much about your safety. A flesh sensor will stop the saw in as little as 0.01s after it comes in contact with your skin. While the blade will be damaged beyond repair, you’ll be safe.Now that you know a bit more about the factors to consider when getting a cabinet table saw, let’s take a better look below at some of the best models you can currently buy.


After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
×